There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@xxxxxx>
Reported-by: Aaro Koskinen <aaro.koskinen@xxxxxx>
Fixes: 15d157e87443 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v1->v2:
- Also free the GPIO in the boardfile bootstrap code so that
the driver can later on properly grab it.
---
arch/arm/mach-omap1/board-osk.c | 4 +++-
drivers/usb/host/ohci-omap.c | 4 ++--
2 files changed, 5 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 144b9caa935c..0a4c9b0b13b0 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -203,6 +203,8 @@ static int osk_tps_setup(struct i2c_client *client, void *context)
*/
gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
+ /* Free the GPIO again as the driver will request it */
+ gpio_free(OSK_TPS_GPIO_USB_PWR_EN);
/* Set GPIO 2 high so LED D3 is off by default */
tps65010_set_gpio_out_value(GPIO2, HIGH);
@@ -288,7 +290,7 @@ static struct gpiod_lookup_table osk_usb_gpio_table = {
.dev_id = "ohci",
.table = {
/* Power GPIO on the I2C-attached TPS65010 */
- GPIO_LOOKUP("i2c-tps65010", 1, "power", GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP("tps65010", 0, "power", GPIO_ACTIVE_HIGH),
GPIO_LOOKUP(OMAP_GPIO_LABEL, 9, "overcurrent",
GPIO_ACTIVE_HIGH),
},
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index 9ccdf2c216b5..6374501ba139 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -91,14 +91,14 @@ static int omap_ohci_transceiver_power(struct ohci_omap_priv *priv, int on)
| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
INNOVATOR_FPGA_CAM_USB_CONTROL);
else if (priv->power)
- gpiod_set_value(priv->power, 0);
+ gpiod_set_value_cansleep(priv->power, 0);
} else {
if (machine_is_omap_innovator() && cpu_is_omap1510())
__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
INNOVATOR_FPGA_CAM_USB_CONTROL);
else if (priv->power)
- gpiod_set_value(priv->power, 1);
+ gpiod_set_value_cansleep(priv->power, 1);
}
return 0;
--
2.26.2
