Hi, +Cc Christoph Hellwig <hch@xxxxxx> Christoph, this is still an issue, so I've been looking around a bit and think this might have something to do with the dma-mapping-5.10 changes. Do you have any suggestions to debug this, or is it time to do a git bisect on this before 5.10 ships with regression? Regards, Hans On 11/10/20 12:36 PM, Hans de Goede wrote: > Hi All, > > Not sure if this is a XHCI driver problem at all, but I needed to start > somewhere with reporting this so I went with: > > scripts/get_maintainer.pl -f drivers/usb/host/xhci-pci.c > > And added a Cc: linux-pci@xxxxxxxxxxxxxxx as bonus. > > I'm seeing the following errors and very slow network performance with > the USB NIC in a Lenovo Thunderbolt gen 2 dock. > > Note that the USB NIC is connected to the XHCI controller which is > embedded inside the dock and is connected over thunderbolt! > > So the errors are: > > [ 1148.744205] swiotlb_tbl_map_single: 6 callbacks suppressed > [ 1148.744210] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1148.744218] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 16ea@1411c0000 dir 1 --- failed > [ 1148.744226] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1148.744368] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1148.744375] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 16ea@10aabc000 dir 1 --- failed > [ 1148.744381] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1148.745141] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1148.745148] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 118e@1411c0000 dir 1 --- failed > [ 1148.745155] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1148.951282] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1148.951388] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 118e@140988000 dir 1 --- failed > [ 1148.951420] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1151.013342] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1151.013357] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 1d2a@1411c0000 dir 1 --- failed > [ 1151.013373] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1151.018660] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 18 (slots) > [ 1151.018696] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 11da@1411c0000 dir 1 --- failed > [ 1151.018711] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1151.223022] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1151.223102] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 11da@10aabc000 dir 1 --- failed > [ 1151.223133] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1151.228810] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1151.228870] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 11da@10aabc000 dir 1 --- failed > [ 1151.228898] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > [ 1151.234792] xhci_hcd 0000:0a:00.0: swiotlb buffer is full (sz: 8192 bytes), total 32768 (slots), used 16 (slots) > [ 1151.234852] xhci_hcd 0000:0a:00.0: DMAR: Device bounce map: 11da@10aabc000 dir 1 --- failed > [ 1151.234882] r8152 4-2.1.2:1.0 ens1u2u1u2: failed tx_urb -11 > > etc. > > This happens as soon as I generate any serious amount of outgoing network traffic. E.g. rsyncing files > to another machine. > > Regards, > > Hans >
