On 2020/11/19 14:09, Greg KH Wrote:
> On Thu, Nov 19, 2020 at 09:50:20AM +0800, liulongfang wrote:
>> On 2020/11/19 0:21, Mathias Nyman Wrote:
>>> On 18.11.2020 11.14, Greg KH wrote:
>>>> On Wed, Nov 18, 2020 at 05:04:36PM +0800, liulongfang wrote:
>>>>> On 2020/11/18 15:02, Greg KH Wrote:
>>>>>> On Wed, Nov 18, 2020 at 11:36:13AM +0800, Longfang Liu wrote:
>>>>>>> The HCE(Host Controller Error) event has been defined in
>>>>>>> the XHCI driver but has not been used. If we want to use
>>>>>>> the HCE event to reset the controller, can we implement
>>>>>>> it in the interrupt function as follows:
>>>>>>>
>>>>>>> xhci_irq()
>>>>>>> |----xhci_halt()
>>>>>>> |----xhci_shutdown()
>>>>>>> |----xhci_start()
>>>>>>> |----xhci_run()
>>>>>>>
>>>>>>> Signed-off-by: Longfang Liu <liulongfang@xxxxxxxxxx>
>>>>>>> ---
>>>>>>> drivers/usb/host/xhci-ring.c | 10 ++++++++++
>>>>>>> 1 file changed, 10 insertions(+)
>>>>>>
>>>>>> $ ./scripts/get_maintainer.pl --file drivers/usb/host/xhci-ring.c
>>>>>> Mathias Nyman <mathias.nyman@xxxxxxxxx> (supporter:USB XHCI DRIVER)
>>>>>> Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> (supporter:USB SUBSYSTEM)
>>>>>> linux-usb@xxxxxxxxxxxxxxx (open list:USB XHCI DRIVER)
>>>>>> linux-kernel@xxxxxxxxxxxxxxx (open list)
>>>>>>
>>>>>> Any reason to not include the maintainer of the xhci driver here?
>>>>> OK, I will include the maintainer in the next patch.
>>>>>>
>>>>>>> diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
>>>>>>> index 2c255d0..87b3a40 100644
>>>>>>> --- a/drivers/usb/host/xhci-ring.c
>>>>>>> +++ b/drivers/usb/host/xhci-ring.c
>>>>>>> @@ -2857,6 +2857,16 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
>>>>>>> goto out;
>>>>>>> }
>>>>>>>
>>>>>>> + if (status & STS_HCE) {
>>>>>>> + xhci_warn(xhci, "WARNING: Host Controller Error\n");
>>>>>>> + xhci_halt(xhci);
>>>>>>> + xhci_shutdown(hcd);
>>>>>>> + xhci_start(xhci);
>>>>>>> + xhci_run(hcd);
>>>>>>> + ret = IRQ_HANDLED;
>>>>>>> + goto out;
>>>>>>> + }
>>> This won't work at all. It doesn't reset the xHC which is the one thing needed to
>>> recover from a HCE. This would deadlock immediately.
>>> Many of the above functions shouldn't be called from interrupt context, and if
>>> HCE is set we probably even won't get any interrupts.
>>>
>>> A reset will set all registers to their initial values, and need to be
>>> re-initialized. Nothing is freed or re-allocated, registrs are not re-initialized
>>> here.
>>>
>>> Please revisit the xhci spec about HCE, and HCRST, and a more detail look
>>> at the xhci driver, and test the code before submitting.
>>>
>>>>>>> +
>>>>>>
>>>>>> Does this fix a real problem for you? Are you sure we will not suddenly
>>>>>> start resetting devices that were working properly and sending this
>>>>>> error incorrectly? How did you test this?
>>>>>>
>>>>>> thanks,
>>>>>>
>>>>>> greg k-h
>>>>>> .
>>>>>>
>>>>> Yes, we want to add a RAS feature to the USB,
>>>>
>>>> What is "RAS"?
>>>>
>>>>> Use the HCE event to trigger the reset operation of the USB controller.
>>>>
>>>> Is that allowed by the XHCI specification?
>>>>
>>>>> By searching for the current xhci driver, the driver did not handle HCE event.
>>>>> In fact, I am not sure if other operations will cause HCE, The HCE event is
>>>>> used to reset the USB controller according to the definition of the event.
>>>>
>>>> What generates that event? Do existing controllers do that today? What
>>>> causes it?
>>>>
>>>
>>> It's not an event, it's a controller internal error state.
>>> It's probably not very useful to check for it in the interrupt handler as
>>> the xHC hw ceases all activity when it sets the HCE bit, including sending
>>> interrupts.
>>>
>>>> >From the spec:
>>>
>>> 4.24.1 Internal Errors
>>> The Host Controller Error (HCE) flag is asserted when an internal xHC error is
>>> detected that exclusively affects the xHC. When the HCE flag is set to ‘1’ the xHC
>>> shall cease all activity. Software response to the assertion of HCE is to reset the
>>> xHC (HCRST = ‘1’) and reinitialize it
>>>
>>>>> I test this reset operation through the Sysfs file, but have not tested all usage scenarios.
>>>>
>>>> What sysfs file?
>>>
>>> I'm also interested in this, and to know more about RAS?
>>>
>>> Thanks
>>> -Mathias
>>> .
>>>
>> RAS: Reliablity, Availability and Serviceability.
>
> That's a marketing phrase, what specifically are you talking about when
> it comes to the xhci driver?
> It means that when the hardware detects HCE, the USB controller could recover.
>> sysfs: a virtual file system based on memory, it's similar as proc.
>
> I am very aware of what sysfs is, look at the MAINTAINERS entry for it :)
>
>> Use DEVICE_ATTR or DRIVER_ATTR to create files to the /sys directory
>
> Yes, but what file did you use for this? I don't see one in the kernel
> that can cause this, do you?
>
> thanks,
>
> greg k-h
> .
>
I found that there is debugfs in the USB xhci driver,
and the reset test can be realized by adding the debugfs file
thanks,
Longfang.
