Lars,
Thank you for your review! The changes which you have suggested also
made ModemManager to recognize the device (which it didn't do before).
Please check out the v2.
Cheers,
Leonid.
___
On 10/4/20 5:32 PM, Lars Melin wrote:
On 10/4/2020 21:16, Lars Melin wrote:
On 10/4/2020 20:29, Leonid Bloch wrote:
On 10/4/20 1:58 PM, Lars Melin wrote:
On 10/4/2020 16:57, Leonid Bloch wrote:
This commit adds the following Telit FT980-KS composition:
0x1054: rndis, diag, adb, nmea, modem, modem, aux
AT commands can be sent to /dev/ttyUSB5.
Please submit a verbose lsusb listing for the device, I can't imagine
that the adb interface should be handled by the option serial driver so
there will never be a ttyUSB5.
Please see below.
Thanks,
Leonid.
```
Bus 001 Device 005: ID 1bc7:1054 Telit Wireless Solutions
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.10
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1bc7 Telit Wireless Solutions
idProduct 0x1054
bcdDevice 4.14
iManufacturer 1 Telit Wireless Solutions
iProduct 2 FT980-KS
iSerial 3 cb42f61
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x013d
bNumInterfaces 8
bConfigurationValue 1
iConfiguration 4 RNDIS_DIAG_ADB_NMEA_DUN_DUN_SER
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 0
bInterfaceCount 2
bFunctionClass 239 Miscellaneous Device
bFunctionSubClass 4
bFunctionProtocol 1
iFunction 7 RNDIS
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 239 Miscellaneous Device
bInterfaceSubClass 4
bInterfaceProtocol 1
iInterface 5 RNDIS Communications Control
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 01
** UNRECOGNIZED: 04 24 02 00
** UNRECOGNIZED: 05 24 06 00 01
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 9
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 6 RNDIS Ethernet Data
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x8e EP 14 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0f EP 15 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 48
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 8 ADB Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
//snip
Interface #3 for ADB must be blacklisted in the option entry for the
device, by using .driver_info = RSVD(3)
When looking at the entries for other Telit deices in the option driver
I see that their diag interface always has
the NCTRL flag so it is likely that you need that for this device also.
See the entry for PID 1052
thanks
Lars
