On Fri, Oct 02, 2020 at 10:10:52PM +0200, Hans de Goede wrote: > Hi, > > On 9/17/20 10:09 PM, Alan Stern wrote: > > On Thu, Sep 17, 2020 at 07:27:03PM +0200, Hans de Goede wrote: > > > Hi, > > > > > > On 9/10/20 5:41 PM, Alan Stern wrote: > > > > On Thu, Sep 10, 2020 at 03:58:49PM +0200, Hans de Goede wrote: > > > > > Hi, > > > > > > > > > > On 9/6/20 4:22 AM, Alan Stern wrote: > > > > > > On Sat, Sep 05, 2020 at 01:37:38PM +0200, Hans de Goede wrote: > > > > > > > Hi All, > > > > > > > > > > > > > > I have been debugging an issue with a 2-in-1 which > > > > > > > consists of a tablet + a kbd-dock, where the device > > > > > > > turns into a clamshell when docked into the kbd-dock. > > > > > > > > > > > > > > The kbd dock is connected via pogo-pins. This works > > > > > > > fine when docked at boot. But there is an enumeration > > > > > > > issue when hot-docked (and the keyboard looses power > > > > > > > when the lid is closedm so this also triggers after > > > > > > > a suspend/resume): > > > > > > > > > > > > > > [ 3498.924190] usb 1-3: new full-speed USB device number 5 using xhci_hcd > > > > > > > [ 3499.041725] usb 1-3: device descriptor read/64, error -71 > > > > > > > [ 3515.215890] usb 1-3: device descriptor read/64, error -110 > > > > > > > [ 3515.440369] usb 1-3: new full-speed USB device number 6 using xhci_hcd > > > > > > > [ 3515.603544] usb 1-3: New USB device found, idVendor=06cb, idProduct=73f5, bcdDevice= 0.02 > > > > > > > [ 3515.603574] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > > > > > > > [ 3515.603596] usb 1-3: Product: ITE Device(8910) > > > > > > > [ 3515.603614] usb 1-3: Manufacturer: ITE Tech. Inc. > > > > > > > > > > > > > > Note there is about 6 seconds before the keyboard becomes > > > > > > > usable, which is quite long when trying to unlock the > > > > > > > laptop after opening the lid. > > > > > > > > > > > > > > If I set the USB_PORT_QUIRK_OLD_SCHEME on the port used by the kbd-dock: > > > > > > > > > > > > > > echo 1 > /sys/devices/pci0000\:00/0000\:00\:14.0/usb1/1-0\:1.0/usb1-port3/quirks > > > > > > > > > > > > > > Then this changes to: > > > > > > > > > > > > > > [ 4467.875008] usb 1-3: new full-speed USB device number 7 using xhci_hcd > > > > > > > [ 4467.878483] usb 1-3: Device not responding to setup address. > > > > > > > [ 4468.082476] usb 1-3: Device not responding to setup address. > > > > > > > [ 4468.289990] usb 1-3: device not accepting address 7, error -71 > > > > > > > [ 4468.614928] usb 1-3: new full-speed USB device number 8 using xhci_hcd > > > > > > > [ 4468.662392] usb 1-3: New USB device found, idVendor=06cb, idProduct=73f5, bcdDevice= 0.02 > > > > > > > [ 4468.662423] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > > > > > > > [ 4468.662444] usb 1-3: Product: ITE Device(8910) > > > > > > > [ 4468.662461] usb 1-3: Manufacturer: ITE Tech. Inc. > > > > > > > > > > > > > > Which is a lot better wrt making the keyboard available for > > > > > > > use in a timely manner. > > > > > > > > > > > > > > So now I'm looking into a way to automatically do this. I would > > > > > > > prefer to keep the handling of this out of the kernel, so I looked into > > > > > > > udev, but it seems that the usb_port_device_type device-s registered by > > > > > > > usb_hub_create_port_device() are not visible to udev? > > > > > > > > > > > > > > At least I'm not seeing them, in the output of "udevadm info -e" > > > > > > > > > > > > My impression is that fixing this would be the simplest approach. > > > > > > > > > > I agree that first trying to fix it is a good idea. > > > > > > <snip> > > > > > > > > > Have you tried decreasing the initial_descriptor_timeout module > > > > > > parameter for usbcore? That would probably help, but it's kind of a > > > > > > sledgehammer. > > > > > > > > > > So I tried this: > > > > > > > > > > [root@localhost ~]# cat /sys/module/usbcore/parameters/initial_descriptor_timeout > > > > > 1000 > > > > > > > > > > But it does not really seem to help: > > > > > > > > > > [ 1171.435346] usb 1-3: USB disconnect, device number 2 > > > > > [ 1180.430958] usb 1-3: new full-speed USB device number 3 using xhci_hcd > > > > > [ 1180.551543] usb 1-3: device descriptor read/64, error -71 > > > > > [ 1184.045548] usb 1-3: device descriptor read/64, error -110 > > > > > [ 1184.270924] usb 1-3: new full-speed USB device number 4 using xhci_hcd > > > > > [ 1184.438336] usb 1-3: New USB device found, idVendor=06cb, idProduct=73f5, bcdDevice= 0.02 > > > > > [ 1184.438371] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > > > > > [ 1184.438399] usb 1-3: Product: ITE Device(8910) > > > > > [ 1184.438425] usb 1-3: Manufacturer: ITE Tech. Inc. > > > > > > > > That part of hub.c is a real mess. Coincidentally, I just posted a > > > > patch to try and fix it up a bit: > > > > > > > > https://marc.info/?l=linux-usb&m=159959185227447&w=2 > > > > > > Ok, I've applied the patch and tried again (with initial_descriptor_timeout still set to 1000), > > > so now the log from the reconnect looks look this: > > > > > > [ 1157.248439] usb 1-3: new full-speed USB device number 3 using xhci_hcd > > > [ 1157.254234] usb 1-3: device descriptor read/64, error -71 > > > [ 1157.371442] usb 1-3: new full-speed USB device number 4 using xhci_hcd > > > [ 1158.377895] usb 1-3: device descriptor read/64, error -110 > > > [ 1158.379646] usb usb1-port3: attempt power cycle > > > [ 1159.014480] usb 1-3: new full-speed USB device number 5 using xhci_hcd > > > [ 1159.176112] usb 1-3: New USB device found, idVendor=06cb, idProduct=73f5, bcdDevice= 0.02 > > > [ 1159.176138] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 > > > [ 1159.176156] usb 1-3: Product: ITE Device(8910) > > > [ 1159.176172] usb 1-3: Manufacturer: ITE Tech. Inc. > > > > > > Still a bit slower then the old probe method, but much better then the > > > new probe method with the default initial_descriptor_timeout. > > > > Yeah, okay, it's good to see that the patch helps. But I'm doubtful > > that the change it makes will become part of the standard (i.e., not > > for embedded systems) kernel. > > > > I still think the udev approach will be best. That will require adding > > various *_uevent_* calls in usb_hub_create_port_device, and adding a > > .uevent member to usb_port_device_type. > > So I tried this and it does not work, the problem is that > dev_uevent_filter() from drivers/base/core.c > filters out uevents for anything which is not either a device > on a bus or a class device: > > static int dev_uevent_filter(struct kset *kset, struct kobject *kobj) > { > struct kobj_type *ktype = get_ktype(kobj); > > if (ktype == &device_ktype) { > struct device *dev = kobj_to_dev(kobj); > if (dev->bus) > return 1; > if (dev->class) > return 1; > } > return 0; > } > > (as mentioned this is a low priority thing for me, so hence > the long time between replies) I'm kind of lost in this thread, but what part of the USB device tree in sysfs is getting "caught" by this filter and does not belong to a bus or class? We can always fix that up if needed. This is the second time this week I have seen this happen in different subsystems where people wanted to do things in userspace for devices that were caught by this. Odd coincidence :) thanks, greg k-h
