Hi On 28.9.2020 16.32, Andrzej Pietrasiewicz wrote: > Hi Ross, hi Mathias, > > W dniu 25.09.2020 o 23:05, Ross Zwisler pisze: >> On Fri, Sep 25, 2020 at 04:40:29PM +0300, Mathias Nyman wrote: >>> On 18.9.2020 17.20, Andrzej Pietrasiewicz wrote: >>>> Hi Mathias, >>>> >>>> W dniu 18.09.2020 o 12:50, Mathias Nyman pisze: >>>>> On 17.9.2020 18.30, Andrzej Pietrasiewicz wrote: >>>>>> Dear All, >>>>>> >>>>>> I have encountered a problem in xhci which leads to general protection fault. >>>>>> >>>>>> The problem is triggered by running this program: >>>>>> >>>>>> https://gitlab.collabora.com/andrzej.p/bulk-cancel.git >>>>>> >>>>>> $ sudo ./bulk-cancel -D /dev/bus/usb/002/006 -i 1 -b 1 >>>>>> >>>>>> where /dev/bus/usb/002/006 is a Gadget Zero: >>>>>> >>>>>> It takes less than a minute until the crash happens. >>>>>> The DMAR (iommu) errors don't happen always, i.e. there are crashes >>>>>> when they are not reported in the system log. In either case the >>>>>> >>>>>> "WARN Cannot submit Set TR Deq Ptr" >>>>>> "A Set TR Deq Ptr command is pending." >>>>>> "WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state." >>>>>> >>>>>> messages do appear. >>>>>> >>>>> >>>>> Nice testcase and report, thanks. >>>>> >>>>> I started looking at issues in this area some time ago, and wrote a couple patches but >>>>> it was left hanging. The two patches (now rebased on 5.9-rc3) can be found in my tree in the >>>>> fix_invalid_context_at_stop_endpoint branch >>>>> >>>>> git://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git fix_invalid_context_at_stop_endpoint >>>>> >>>>> https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=fix_invalid_context_at_stop_endpoint >>>>> >>>>> If you could give those a try and see if they help I'd be grateful. >>>> >>>> No, it doesn't help, albeit the errors are slightly different: >>>> >>>> xhci_hcd 0000:00:14.0: WARN Cannot submit Set TR Deq Ptr >>>> xhci_hcd 0000:00:14.0: A Set TR Deq Ptr command is pending. >>>> dmar_fault: 44 callbacks suppressed >>>> DRHD: handling fault status reg 3> DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr ffcda000 [fault reason 05] PTE Write access is not set >>>> DMAR: DRHD: handling fault status reg 3 >>> >>> Ok, thanks, the DMA problems make sense to me now. >>> >>> If a transfer ring stops on a transfer request (TRB) that should be canceled (manual cancel, >>> or error) it's not enough to just turn the TRB to a no-op. >>> HW has most likely cached the TRB, and we need to move the transfer ring dequeue pointer past this TRB. >>> Moving deq also clears controller cache. >>> >>> We do all this, but if we fail to queue the Set TR Deq command the TRB (with DMA pointers) will stay on the ring, >>> and controller will access the TRB DMA address once it continues running. At this point xhci driver has already >>> given back the canceled/erroneous TRB, and is probably unmapped already. >>> Hence the DMAR entries. >>> >>> Looks like this part of the code needs a more extensive rewrite, on top of this we are not handling >>> races between endpoints halted due errors, and endpoints stopped by driver to cancel URBs. >>> >>> -Mathias >> >> I'm chasing a similar problem which is also most easily reproduced using >> Andrzej's bulk-cancel program, though we have seen it in the field many times >> as well with normal usage. >> >> The symptom is that we get the following errors in dmesg: >> >> xhci_hcd 0000:00:14.0: Mismatch between completed Set TR Deq Ptr command & xHCI internal state. >> xhci_hcd 0000:00:14.0: ep deq seg = 000000001141d6a0, deq ptr = 00000000ebd28dcf >> xhci_hcd 0000:00:14.0: WARNING: Host System Error >> DMAR: DRHD: handling fault status reg 2 >> DMAR: [DMA Read] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 06] PTE Read access is not set >> xhci_hcd 0000:00:14.0: xHCI host not responding to stop endpoint command. >> xhci_hcd 0000:00:14.0: USBSTS: HCHalted HSE EINT >> xhci_hcd 0000:00:14.0: xHCI host controller not responding, assume dead >> xhci_hcd 0000:00:14.0: HC died; cleaning up >> >> The xhci USB stack loses all attached devices, and on my system at least has >> only been recoverable by rebooting. >> >> Full dmesg and trace after 'echo 1 > /sys/kernel/debug/tracing/events/xhci-hcd/enable' >> can be found here: >> >> https://gist.github.com/rzwisler/531b926e3d160609ead371c23fc15b55 >> https://gist.github.com/rzwisler/4621f805737993fec30b5ae23bfd8289 >> >> One interesting bit from the trace is that we observe the ep_ctx->deq pointer >> being 0 in xhci_handle_cmd_set_deq(): >> >> xhci_inc_enq: CMD 000000000b6352e0: enq 0x00000000ffffe0c0(0x00000000ffffe000) deq 0x00000000ffffe090(0x00000000ffffe000) segs 1 stream 0 free_trbs 251 bounce 0 cycle 0 >> xhci_ring_host_doorbell: Ring doorbell for Command Ring 0 >> xhci_urb_giveback: ep7in-bulk: urb 000000003c80b7a8 pipe 3221455744 slot 2 length 0/256 sgs 0/0 stream 0 flags 00010200 >> xhci_inc_deq: CMD 000000000b6352e0: enq 0x00000000ffffe0c0(0x00000000ffffe000) deq 0x00000000ffffe0a0(0x00000000ffffe000) segs 1 stream 0 free_trbs 252 bounce 0 cycle 0 >> xhci_inc_deq: EVENT 00000000b5c6e6a2: enq 0x00000000ffffc000(0x00000000ffffc000) deq 0x00000000ffffc1b0(0x00000000ffffc000) segs 1 stream 0 free_trbs 254 bounce 0 cycle 1 >> xhci_handle_event: EVENT: TRB 00000000ffffe0a0 status 'Success' len 0 slot 4 ep 0 type 'Command Completion Event' flags e:C >> xhci_handle_command: CMD: Set TR Dequeue Pointer Command: deq 00000000fff296a1 stream 0 slot 4 ep 3 flags c >> xhci_handle_cmd_set_deq: RS 00000 full-speed Ctx Entries 15 MEL 0 us Port# 13/0 [TT Slot 0 Port# 0 TTT 0 Intr 0] Addr 4 State configured >> xhci_handle_cmd_set_deq_ep: State stopped mult 1 max P. Streams 0 interval 125 us max ESIT payload 0 CErr 3 Type Bulk IN burst 0 maxp 64 deq 0000000000000000 avg trb len 0 >> ^^^^^^^^^^^^^^^^^^^^ >> xhci_dbg_cancel_urb: Successful Set TR Deq Ptr cmd, deq = @00000000 >> ^^^^^^^^^^^^^^^ >> >> In successful completions they are real values: >> >> xhci_ring_ep_doorbell: Ring doorbell for Slot 4 ep1in >> xhci_inc_deq: CMD 000000000b6352e0: enq 0x00000000ffffe0c0(0x00000000ffffe000) deq 0x00000000ffffe0b0(0x00000000ffffe000) segs 1 stream 0 free_trbs 253 bounce 0 cycle 0 >> xhci_inc_deq: EVENT 00000000b5c6e6a2: enq 0x00000000ffffc000(0x00000000ffffc000) deq 0x00000000ffffc1c0(0x00000000ffffc000) segs 1 stream 0 free_trbs 254 bounce 0 cycle 1 >> xhci_handle_event: EVENT: TRB 00000000ffffe0b0 status 'Success' len 0 slot 2 ep 0 type 'Command Completion Event' flags e:C >> xhci_handle_command: CMD: Set TR Dequeue Pointer Command: deq 00000000fff86551 stream 0 slot 2 ep 15 flags c >> xhci_handle_cmd_set_deq: RS 00000 full-speed Ctx Entries 15 MEL 0 us Port# 11/0 [TT Slot 0 Port# 0 TTT 0 Intr 0] Addr 2 State configured >> xhci_handle_cmd_set_deq_ep: State stopped mult 1 max P. Streams 0 interval 125 us max ESIT payload 0 CErr 3 Type Bulk IN burst 0 maxp 16 deq 00000000fff86551 avg trb len 0 >> ^^^^^^^^^^^^^^^^^^^^ >> xhci_dbg_cancel_urb: Successful Set TR Deq Ptr cmd, deq = @fff86550 >> ^^^^^^^^^^^^^^^ >> >> I've noticed that I have to have CONFIG_INTEL_IOMMU_DEFAULT_ON=y for this >> clean repro case, else the system still fails but I don't always (ever?) see >> the failure to read at address 0. >> >> Mathias, do you think that your above explanation also covers my failure case? >> Are we just failing to enqueue a Set TR Deq command, and the HC is processing >> a stale TRB? Or does the fact that ep_ctx->deq == 0 not fit with that >> explanation? >> > > From the logs from Ross it seems that the direct cause of the HC dying > is Stop Endpoint not completing and, consequently, timing out. Stop endpoint command does not complete due to the 'catastrophic' HSE (host system error) which stops the controller completely. I'd guess the HSE is related to the zeroed dequeue pointer. > > In the xHCI spec, section "4.6.9 Stop Endpoint" we can read: > > "Note that when an endpoint is stopped, the xHC maintains the state > necessary to restart the last active Transfer Ring where it left off, > however software may not want to do this. The options are discussed below: > > 1. Temporarily Stop Transfer Ring Activity - [...] > > 2. Aborting a Transfer - If, because of a timeout or other reason, software > issued the Stop Endpoint Command to abort the current TD. Then the > Set TR Dequeue Pointer Command may be used to force the xHC to > dump any internal state that it has for the ring and restart activity at the > new Transfer Ring location specified by the Set TR Dequeue Pointer Command." > > If bulk-cancel reproducer is used then the software's intention is definitely > to abort a transfer, so indeed a Set TR Dequeue Pointer is needed. > > On the other hand, in that same spec, in "4.6.10 Set TR Dequeue Pointer" > we read: > > "This command may be executed only if the target endpoint is in the Error > or Stopped state." > > My question is: why in the crash scenario Ross describes "Set TR Dequeue > Pointer" is being carried out while Stop Endpoint has not been completed > (and timed out instead)? Every time a URB is canceled the xhci driver will queue a "stop endpoint command" if there isn't one already pending. The Set TR Dequeue command you see is probably for the previous URB, while the stop is for the next URB. Andrzej, any change of getting traces from your case? They would tell more than just the dynamic debug. Thanks -Mathias
