Hi,
Wesley Cheng wrote:
> In the DWC3 databook, for a device initiated disconnect, the driver is
> required to send dependxfer commands for any pending transfers.
> In addition, before the controller can move to the halted state, the SW
> needs to acknowledge any pending events. If the controller is not halted
> properly, there is a chance the controller will continue accessing stale or
> freed TRBs and buffers.
>
> Signed-off-by: Wesley Cheng <wcheng@xxxxxxxxxxxxxx>
>
> ---
> Verified fix by adding a check for ETIMEDOUT during the run stop call.
> Shell script writing to the configfs UDC file to trigger disconnect and
> connect. Batch script to have PC execute data transfers over adb (ie adb
> push) After a few iterations, we'd run into a scenario where the
> controller wasn't halted. With the following change, no failed halts after
> many iterations.
> ---
> drivers/usb/dwc3/ep0.c | 2 +-
> drivers/usb/dwc3/gadget.c | 59 +++++++++++++++++++++++++++++++++++++--
> 2 files changed, 57 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
> index 59f2e8c31bd1..456aa87e8778 100644
> --- a/drivers/usb/dwc3/ep0.c
> +++ b/drivers/usb/dwc3/ep0.c
> @@ -197,7 +197,7 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
> int ret;
>
> spin_lock_irqsave(&dwc->lock, flags);
> - if (!dep->endpoint.desc) {
> + if (!dep->endpoint.desc || !dwc->pullups_connected) {
> dev_err(dwc->dev, "%s: can't queue to disabled endpoint\n",
> dep->name);
> ret = -ESHUTDOWN;
> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
> index 3ab6f118c508..1f981942d7f9 100644
> --- a/drivers/usb/dwc3/gadget.c
> +++ b/drivers/usb/dwc3/gadget.c
> @@ -1516,7 +1516,7 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
> {
> struct dwc3 *dwc = dep->dwc;
>
> - if (!dep->endpoint.desc) {
> + if (!dep->endpoint.desc || !dwc->pullups_connected) {
> dev_err(dwc->dev, "%s: can't queue to disabled endpoint\n",
> dep->name);
> return -ESHUTDOWN;
> @@ -1926,6 +1926,24 @@ static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,
> return 0;
> }
>
> +static void dwc3_stop_active_transfers(struct dwc3 *dwc)
> +{
> + u32 epnum;
> +
> + for (epnum = 2; epnum < DWC3_ENDPOINTS_NUM; epnum++) {
> + struct dwc3_ep *dep;
> +
> + dep = dwc->eps[epnum];
> + if (!dep)
> + continue;
> +
> + if (!(dep->flags & DWC3_EP_ENABLED))
> + continue;
> +
> + dwc3_remove_requests(dwc, dep);
> + }
> +}
> +
> static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
> {
> u32 reg;
> @@ -1950,16 +1968,37 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
>
> dwc->pullups_connected = true;
> } else {
> + dwc->pullups_connected = false;
> +
> + __dwc3_gadget_ep_disable(dwc->eps[0]);
> + __dwc3_gadget_ep_disable(dwc->eps[1]);
run_stop() function shouldn't be doing this. This is done in
dwc3_gadget_stop(). Also, if it's device-initiated disconnect, driver
needs to wait for control transfers to complete.
> +
> + /*
> + * The databook explicitly mentions for a device-initiated
> + * disconnect sequence, the SW needs to ensure that it ends any
> + * active transfers.
> + */
> + dwc3_stop_active_transfers(dwc);
It shouldn't be done here. Maybe move this to the dwc3_gadget_pullup()
function. The run_stop() function can be called for other context beside
this (e.g. hibernation).
> +
> reg &= ~DWC3_DCTL_RUN_STOP;
>
> if (dwc->has_hibernation && !suspend)
> reg &= ~DWC3_DCTL_KEEP_CONNECT;
> -
> - dwc->pullups_connected = false;
> }
>
> dwc3_gadget_dctl_write_safe(dwc, reg);
>
> + /* Controller is not halted until pending events are acknowledged */
> + if (!is_on) {
> + reg = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
> + reg &= DWC3_GEVNTCOUNT_MASK;
> + if (reg > 0) {
> + dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), reg);
> + dwc->ev_buf->lpos = (dwc->ev_buf->lpos + reg) %
> + dwc->ev_buf->length;
> + }
> + }
> +
Driver should handle the events before clearing the run_stop bit, not
just acknowledging and ignoring them.
> do {
> reg = dwc3_readl(dwc->regs, DWC3_DSTS);
> reg &= DWC3_DSTS_DEVCTRLHLT;
> @@ -1994,9 +2033,15 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
> }
> }
>
> + /*
> + * Synchronize and disable any further event handling while controller
> + * is being enabled/disabled.
> + */
> + disable_irq(dwc->irq_gadget);
> spin_lock_irqsave(&dwc->lock, flags);
> ret = dwc3_gadget_run_stop(dwc, is_on, false);
> spin_unlock_irqrestore(&dwc->lock, flags);
> + enable_irq(dwc->irq_gadget);
>
> return ret;
> }
> @@ -3535,6 +3580,14 @@ static irqreturn_t dwc3_check_event_buf(struct dwc3_event_buffer *evt)
> if (!count)
> return IRQ_NONE;
>
> + /* Controller is halted; ignore new/pending events */
> + if (!dwc->pullups_connected) {
> + dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
> + dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
> + dwc->ev_buf->length;
> + return IRQ_HANDLED;
> + }
> +
Why? Are you getting any event after the controller is halted? Also,
make sure to take account of hibernation. The controller can get PMU
event after halted to bring it out of hibernation.
> evt->count = count;
> evt->flags |= DWC3_EVENT_PENDING;
>
If you're making these fixes, can you also fix handling reset interrupt
? It also needs to end all the active transfers.
Thanks,
Thinh
