This patch adds a driver for configuration of the Microchip USB49xx/xi USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus configuration interface and two to four USB 2.0 downstream ports. Furthermore add myself as a maintainer for this driver. The datasheet can be found at the manufacturers website, see [1]. All device-tree exposed configuration features have been tested on a i.MX6 platform with a USB4916 hub. [1] http://ww1.microchip.com/downloads/en/Appnotes/AN2651-Configuration-of-Microchip-USB47xx-USB49xx-Application-Note-00002651B.pdf Signed-off-by: Christian Eggers <ceggers@xxxxxxx> --- MAINTAINERS | 7 + drivers/usb/misc/Kconfig | 10 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/usb49xx.c | 825 +++++++++++++++++++++++++++++++++++++ 4 files changed, 843 insertions(+) create mode 100644 drivers/usb/misc/usb49xx.c diff --git a/MAINTAINERS b/MAINTAINERS index fe1108ba6ce7..068d6e94122b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -11363,6 +11363,13 @@ S: Maintained F: Documentation/devicetree/bindings/usb/usb253x.yaml F: drivers/usb/misc/usb253x.c +MICROCHIP USB49XX DRIVER +M: Christian Eggers <ceggers@xxxxxxx> +L: linux-usb@xxxxxxxxxxxxxxx +S: Maintained +F: Documentation/devicetree/bindings/usb/usb49xx.yaml +F: drivers/usb/misc/usb49xx.c + MICROCHIP USBA UDC DRIVER M: Cristian Birsan <cristian.birsan@xxxxxxxxxxxxx> L: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx (moderated for non-subscribers) diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 7a7b854e803a..14bea87c0f81 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -252,6 +252,16 @@ config USB_HUB_USB253X Configuration parameters may be set in devicetree or platform data. Say Y or M here if you need to configure such a device via I2C. +config USB_HUB_USB49XX + tristate "USB47XX/USB49XX Hub Controller Configuration Driver" + depends on I2C + select REGMAP + help + This option enables support for configuration via I2C bus of the + Microchip USB47xx/49xx USB 2.0 Hub Controller series. + Configuration parameters may be set in devicetree or platform data. + Say Y or M here if you need to configure such a device via I2C. + config USB_HSIC_USB3503 tristate "USB3503 HSIC to USB20 Driver" depends on I2C diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 6fd8c53841e4..3832858aba1e 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -26,6 +26,7 @@ obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o obj-$(CONFIG_USB_YUREX) += yurex.o obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o obj-$(CONFIG_USB_HUB_USB253X) += usb253x.o +obj-$(CONFIG_USB_HUB_USB49XX) += usb49xx.o obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o diff --git a/drivers/usb/misc/usb49xx.c b/drivers/usb/misc/usb49xx.c new file mode 100644 index 000000000000..b713ef4557c2 --- /dev/null +++ b/drivers/usb/misc/usb49xx.c @@ -0,0 +1,825 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for Microchip USB47xx and USB49xx USB 2.0 Hi-Speed Hub Controller + * Configuration via I2C. + * + * Copyright (c) 2020 ARRI Lighting + * + * This work is based on the USB251xb driver by Richard Leitner. + * + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/gpio/driver.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/nls.h> +#include <linux/of_device.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +/* Internal Register Set Addresses acc. to DS00002651B */ +#define USB49XX_ADDR_VENDOR_ID 0xBF803000 +#define USB49XX_ADDR_PRODUCT_ID 0xBF803002 +#define USB49XX_ADDR_DEVICE_ID 0xBF803004 +#define USB49XX_ADDR_HUB_CFG 0xBF803006 +#define USB49XX_HUB_CFG3_PRTMAP_EN BIT(3) +#define USB49XX_HUB_CFG3_STRING_EN BIT(0) +#define USB49XX_ADDR_NON_REMOVABLE_DEVICES 0xBF803009 +#define USB49XX_ADDR_PORT_DISABLE_SELF 0xBF80300A +#define USB49XX_ADDR_PORT_DISABLE_BUS 0xBF80300B +#define USB49XX_ADDR_POWER_ON_TIME 0xBF803010 +#define USB49XX_ADDR_OCS_MIN_WIDTH 0xBF8030EA +#define USB49XX_ADDR_LANGUAGE_ID 0xBF803202 +#define USB49XX_STRING_BUFSIZE 62 +#define USB49XX_ADDR_MANUFACTURER_STRING_DESC 0xBFD23204 +#define USB49XX_ADDR_PRODUCT_STRING_DESC 0xBFD23244 +#define USB49XX_ADDR_MANUFACTURER_STRING_LEN 0xBFD2346A +#define USB49XX_ADDR_PRODUCT_STRING_LEN 0xBFD23472 +#define USB49XX_ADDR_USB2_HUB_CTRL 0xBF803104 +#define USB49XX_USB2_HUB_CTRL_LPM_DISABLE BIT(1) + +#define DRIVER_NAME "usb49xx" + + +struct usb49xx { + struct device *dev; + struct i2c_client *i2c; + struct regulator *vdd; + struct regmap *regmap; + u8 skip_config; + struct gpio_desc *gpio_reset; +}; + +#ifdef CONFIG_GPIOLIB +static int usb49xx_check_dev_children(struct device *dev, void *child) +{ + if (dev->type == &i2c_adapter_type) { + return device_for_each_child(dev, child, + usb49xx_check_dev_children); + } + + return (dev == child); +} + +static int usb49xx_check_gpio_chip(struct usb49xx *hub) +{ + struct gpio_chip *gc = gpiod_to_chip(hub->gpio_reset); + struct i2c_adapter *adap = hub->i2c->adapter; + int ret; + + if (!hub->gpio_reset) + return 0; + + if (!gc) + return -EINVAL; + + ret = usb49xx_check_dev_children(&adap->dev, gc->parent); + if (ret) { + dev_err(hub->dev, "Reset GPIO chip is at the same i2c-bus\n"); + return -EINVAL; + } + + return 0; +} +#else +static int usb49xx_check_gpio_chip(struct usb49xx *hub) +{ + return 0; +} +#endif + +static void usb49xx_reset(struct usb49xx *hub, int state) +{ + if (state) { + /* During rising edge of reset, there must be no traffic on the i2c bus */ + i2c_lock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT); + gpiod_set_value_cansleep(hub->gpio_reset, 1); + /* Wait for i2c logic to come up (hub seems to require ~10 ms)*/ + msleep(20); + i2c_unlock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT); + } else { + gpiod_set_value_cansleep(hub->gpio_reset, 0); + /* minimum reset pulse width is 5 us */ + usleep_range(5, 10); + } +} + +struct usb49xx_string_desc { + u8 length; /* length of string in bytes + 2 */ + u8 type; /* always 0x03 */ + wchar_t string[USB49XX_STRING_BUFSIZE/sizeof(wchar_t)]; +}; + +static void usb49xx_get_ports_field(struct usb49xx *hub, + const char *prop_name, u8 port_cnt, + u8 *fld) +{ + struct device *dev = hub->dev; + struct property *prop; + const __be32 *p; + u32 port; + + of_property_for_each_u32(dev->of_node, prop_name, prop, p, port) { + if ((port >= 1) && (port <= port_cnt)) + *fld |= BIT(port); + else + dev_warn(dev, "port %u doesn't exist\n", port); + } +} + +static int usb49xx_connect(struct usb49xx *hub) +{ + struct device *dev = hub->dev; + struct device_node *np = dev->of_node; + int err; + char attach_buffer[3]; + + usb49xx_reset(hub, 1); + + if (hub->skip_config) { + dev_info(dev, "Skip hub configuration, only attach.\n"); + } else { + u16 vendor_id, product_id, device_id, lang_id; + u8 hub_cfg[3]; + u32 property_u32; + char const *manufacturer; + char const *product; + u8 non_rem_dev = 0; + u8 port_disable_sp = 0; + u8 port_disable_bp = 0; + + if (!of_property_read_u16_array(np, "vendor-id", &vendor_id, 1)) { + char buffer[] = { vendor_id >> 8, vendor_id }; + + err = regmap_bulk_write(hub->regmap, USB49XX_ADDR_VENDOR_ID, + buffer, ARRAY_SIZE(buffer)); + if (err) { + dev_err(dev, "Setting vendor id failed: %d\n", err); + return err; + } + } + + if (!of_property_read_u16_array(np, "product-id", &product_id, 1)) { + char buffer[] = { product_id >> 8, product_id }; + + err = regmap_bulk_write(hub->regmap, USB49XX_ADDR_PRODUCT_ID, + buffer, ARRAY_SIZE(buffer)); + if (err) { + dev_err(dev, "Setting product id failed: %d\n", err); + return err; + } + } + + if (!of_property_read_u16_array(np, "device-id", &device_id, 1)) { + char buffer[] = { device_id >> 8, device_id }; + + err = regmap_bulk_write(hub->regmap, USB49XX_ADDR_DEVICE_ID, + buffer, ARRAY_SIZE(buffer)); + if (err) { + dev_err(dev, "Setting device id failed: %d\n", err); + return err; + } + } + + err = regmap_bulk_read(hub->regmap, USB49XX_ADDR_HUB_CFG, + hub_cfg, ARRAY_SIZE(hub_cfg)); + if (err) { + dev_err(dev, "Reading hub cfg failed: %d\n", err); + return err; + } + + if (of_get_property(np, "self-powered", NULL)) { + hub_cfg[0] |= BIT(7); + + /* Configure Over-Current sens when self-powered */ + hub_cfg[0] &= ~BIT(2); + if (of_get_property(np, "ganged-sensing", NULL)) + hub_cfg[0] &= ~BIT(1); + else if (of_get_property(np, "individual-sensing", NULL)) + hub_cfg[0] |= BIT(1); + } else if (of_get_property(np, "bus-powered", NULL)) { + hub_cfg[0] &= ~BIT(7); + + /* Disable Over-Current sense when bus-powered */ + hub_cfg[0] |= BIT(2); + } + + if (of_get_property(np, "disable-hi-speed", NULL)) + hub_cfg[0] |= BIT(5); + + if (of_get_property(np, "multi-tt", NULL)) + hub_cfg[0] |= BIT(4); + else if (of_get_property(np, "single-tt", NULL)) + hub_cfg[0] &= ~BIT(4); + + if (of_get_property(np, "disable-eop", NULL)) + hub_cfg[0] |= BIT(3); + + if (of_get_property(np, "individual-port-switching", NULL)) + hub_cfg[0] |= BIT(0); + else if (of_get_property(np, "ganged-port-switching", NULL)) + hub_cfg[0] &= ~BIT(0); + + if (of_get_property(np, "dynamic-power-switching", NULL)) + hub_cfg[1] |= BIT(7); + + if (!of_property_read_u32(np, "oc-delay-ns", &property_u32)) { + if (property_u32 == 50) { + /* 50 ns*/ + hub_cfg[1] &= ~BIT(5); + hub_cfg[1] &= ~BIT(4); + } else if (property_u32 == 100) { + /* 100 ns */ + hub_cfg[1] &= ~BIT(5); + hub_cfg[1] |= BIT(4); + } else if (property_u32 == 200) { + /* 400 ns */ + hub_cfg[1] |= BIT(5); + hub_cfg[1] |= BIT(4); + } else { + /* 200 ns (DEFAULT) */ + hub_cfg[1] |= BIT(5); + hub_cfg[1] &= ~BIT(4); + } + } + + if (of_get_property(np, "compound-device", NULL)) + hub_cfg[1] |= BIT(3); + + if (of_get_property(np, "port-mapping-mode", NULL)) + hub_cfg[2] |= USB49XX_HUB_CFG3_PRTMAP_EN; + + /* port mapping requires that Link Power Management is disabled */ + if (hub_cfg[2] & USB49XX_HUB_CFG3_PRTMAP_EN) { + unsigned int usb2_hub_ctrl; + + /* Disable Link Power Management */ + err = regmap_read(hub->regmap, USB49XX_ADDR_USB2_HUB_CTRL, + &usb2_hub_ctrl); + if (err) { + dev_err(dev, "Reading USB2 Hub Control failed: %d\n", err); + return err; + } + + usb2_hub_ctrl |= USB49XX_USB2_HUB_CTRL_LPM_DISABLE; + + err = regmap_write(hub->regmap, USB49XX_ADDR_USB2_HUB_CTRL, + usb2_hub_ctrl); + if (err) { + dev_err(dev, "Writing USB2 Hub Control failed: %d\n", err); + return err; + } + } + + manufacturer = of_get_property(np, "manufacturer", NULL); + product = of_get_property(np, "product", NULL); + + if (manufacturer || product) + hub_cfg[2] |= USB49XX_HUB_CFG3_STRING_EN; + + err = regmap_bulk_write(hub->regmap, USB49XX_ADDR_HUB_CFG, + hub_cfg, ARRAY_SIZE(hub_cfg)); + if (err) { + dev_err(dev, "Setting hub cfg failed: %d\n", err); + return err; + } + + usb49xx_get_ports_field(hub, "non-removable-ports", 5, &non_rem_dev); + err = regmap_write(hub->regmap, USB49XX_ADDR_NON_REMOVABLE_DEVICES, + non_rem_dev); + if (err) { + dev_err(dev, "Setting non removable devices failed: %d\n", err); + return err; + } + + usb49xx_get_ports_field(hub, "sp-disabled-ports", 7, &port_disable_sp); + err = regmap_write(hub->regmap, USB49XX_ADDR_PORT_DISABLE_SELF, + port_disable_sp); + if (err) { + dev_err(dev, "Setting port disable self powered failed: %d\n", err); + return err; + } + + usb49xx_get_ports_field(hub, "bp-disabled-ports", 7, &port_disable_bp); + err = regmap_write(hub->regmap, USB49XX_ADDR_PORT_DISABLE_BUS, + port_disable_bp); + if (err) { + dev_err(dev, "Setting port disable powered powered failed: %d\n", err); + return err; + } + + if (!of_property_read_u32(np, "power-on-time-ms", &property_u32)) { + u8 power_on_time = min_t(u8, property_u32 / 2, 255); + + err = regmap_write(hub->regmap, USB49XX_ADDR_POWER_ON_TIME, + power_on_time); + if (err) { + dev_err(dev, "Setting power on time failed: %d\n", err); + return err; + } + } + + if (!of_property_read_u32(np, "ocs-min-width-ms", &property_u32)) { + u8 ocs_min_width = min_t(u8, property_u32, 5); + + err = regmap_write(hub->regmap, USB49XX_ADDR_OCS_MIN_WIDTH, + ocs_min_width); + if (err) { + dev_err(dev, "Setting ocs min width failed: %d\n", err); + return err; + } + } + + if (!of_property_read_u16_array(np, "language-id", &lang_id, 1)) { + char buffer[] = { lang_id >> 8, lang_id }; + + err = regmap_bulk_write(hub->regmap, USB49XX_ADDR_LANGUAGE_ID, + buffer, ARRAY_SIZE(buffer)); + if (err) { + dev_err(dev, "Setting language id failed: %d\n", err); + return err; + } + } + + if (manufacturer) { + struct usb49xx_string_desc manufacturer_desc; + + memset(&manufacturer_desc, 0, sizeof(manufacturer_desc)); + manufacturer_desc.type = 0x3; + manufacturer_desc.length = + utf8s_to_utf16s(manufacturer, strlen(manufacturer), + UTF16_LITTLE_ENDIAN, + manufacturer_desc.string, USB49XX_STRING_BUFSIZE) + * sizeof(wchar_t) + 2; + + err = regmap_bulk_write(hub->regmap, + USB49XX_ADDR_MANUFACTURER_STRING_DESC, + &manufacturer_desc, sizeof(manufacturer_desc)); + if (err) { + dev_err(dev, "Setting manufacturer string descriptor failed: %d\n", + err); + return err; + } + + err = regmap_write(hub->regmap, USB49XX_ADDR_MANUFACTURER_STRING_LEN, + manufacturer_desc.length); + if (err) { + dev_err(dev, "Setting manufacturer string length failed: %d\n", + err); + return err; + } + } + + if (product) { + struct usb49xx_string_desc product_desc; + + memset(&product_desc, 0, sizeof(product_desc)); + product_desc.type = 0x3; + product_desc.length = utf8s_to_utf16s(product, strlen(product), + UTF16_LITTLE_ENDIAN, + product_desc.string, USB49XX_STRING_BUFSIZE) + * sizeof(wchar_t) + 2; + + err = regmap_bulk_write(hub->regmap, + USB49XX_ADDR_PRODUCT_STRING_DESC, + &product_desc, sizeof(product_desc)); + if (err) { + dev_err(dev, "Setting product string descriptor failed: %d\n", err); + return err; + } + + err = regmap_write(hub->regmap, USB49XX_ADDR_PRODUCT_STRING_LEN, + product_desc.length); + if (err) { + dev_err(dev, "SSetting product string length failed: %d\n", err); + return err; + } + } + } + +#ifdef DEBUG + { + char *buffer = kzalloc(0x5000, GFP_KERNEL); + + err = regmap_bulk_read(hub->regmap, 0xBF800000, buffer, 0x4); + print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buffer, 0x4); + err = regmap_bulk_read(hub->regmap, 0xBF803000, buffer, 0x200); + print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buffer, 0x200); + err = regmap_bulk_read(hub->regmap, 0xBFD23200, buffer, 0x200); + print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buffer, 0x200); + kfree(buffer); + } +#endif + + /* + * attach + */ + /* n.b. Could also use 0xAA56 (attach with SMBus runtime access) */ + attach_buffer[0] = 0xAA; /* USB attach (high byte) */ + attach_buffer[1] = 0x56; /* USB attach (low byte) */ + attach_buffer[2] = 0x00; /* terminator */ + + err = i2c_master_send(hub->i2c, attach_buffer, 3); + if (err != 3) { + dev_err(dev, "attaching hub failed: %d\n", err); + return err; + } + + dev_info(dev, "Hub configuration was successful.\n"); + return 0; + +} + +#ifdef CONFIG_OF +static int usb49xx_get_ofdata(struct usb49xx *hub) +{ + struct device *dev = hub->dev; + struct device_node *np = dev->of_node; + + if (!np) { + dev_err(dev, "failed to get ofdata\n"); + return -ENODEV; + } + + if (of_get_property(np, "skip-config", NULL)) + hub->skip_config = 1; + else + hub->skip_config = 0; + + hub->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(hub->gpio_reset)) + return PTR_ERR(hub->gpio_reset); + + return 0; +} + +static const struct of_device_id usb49xx_of_match[] = { + { .compatible = "microchip,usb4712", }, + { .compatible = "microchip,usb4712i", }, + { .compatible = "microchip,usb4715", }, + { .compatible = "microchip,usb4715i", }, + { .compatible = "microchip,usb4912", }, + { .compatible = "microchip,usb4912i", }, + { .compatible = "microchip,usb4914", }, + { .compatible = "microchip,usb4914i", }, + { .compatible = "microchip,usb4916", }, + { .compatible = "microchip,usb4916i", }, + { .compatible = "microchip,usb4925", }, + { .compatible = "microchip,usb4925i", }, + { .compatible = "microchip,usb4927", }, + { .compatible = "microchip,usb4927i", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, usb49xx_of_match); +#else /* CONFIG_OF */ +static int usb49xx_get_ofdata(struct usb49xx *hub) +{ + return 0; +} +#endif /* CONFIG_OF */ + +static void usb49xx_regulator_disable_action(void *data) +{ + struct usb49xx *hub = data; + + regulator_disable(hub->vdd); +} + +static int usb49xx_probe(struct usb49xx *hub) +{ + struct device *dev = hub->dev; + struct device_node *np = dev->of_node; + int err; + + if (np) { + err = usb49xx_get_ofdata(hub); + if (err) { + dev_err(dev, "failed to get ofdata: %d\n", err); + return err; + } + } + + /* + * The usb49xx performs a check on the SMBus during the SMBUS_CHECK state. + * In order to successful, SCL and SDA must be stable at this moment. + * Normally we could just lock the SMBus-segment the + * hub i2c-interface resides for the device-specific reset timing. But + * the GPIO controller, which is used to handle the hub reset, might be + * placed at the same i2c-bus segment. In this case an error should be + * returned since we can't safely use the GPIO controller to clear the + * reset state (it may affect the hub configuration) and we can't lock + * the i2c-bus segment (it will cause a deadlock). + */ + err = usb49xx_check_gpio_chip(hub); + if (err) + return err; + + hub->vdd = devm_regulator_get(dev, "vdd"); + if (IS_ERR(hub->vdd)) + return PTR_ERR(hub->vdd); + + err = regulator_enable(hub->vdd); + if (err) + return err; + + err = devm_add_action_or_reset(dev, + usb49xx_regulator_disable_action, hub); + if (err) + return err; + + err = usb49xx_connect(hub); + if (err) { + dev_err(dev, "Failed to connect hub (%d)\n", err); + return err; + } + + dev_info(dev, "Hub probed successfully\n"); + + return 0; +} + +static int usb49xx_i2c_gather_write(void *context, + const void *reg, size_t reg_len, + const void *val, size_t val_len) +{ + struct i2c_client *i2c = (struct i2c_client *)context; + size_t frame_len = val_len + 9; + char *buffer; + int err; + + if (WARN_ON(reg_len != 4)) + return -EINVAL; + + buffer = kmalloc(frame_len, GFP_KERNEL); + if (!buffer) + return -ENOMEM; + + buffer[0] = 0x00; /* Memory address (high byte) */ + buffer[1] = 0x00; /* Memory address (low byte) */ + buffer[2] = val_len + 6; /* Number of bytes to write to memory */ + buffer[3] = 0x00; /* Register Write */ + buffer[4] = val_len; /* Write val_len data bytes */ + buffer[5] = *((const char *)reg + 0); /* Register address (MSB) */ + buffer[6] = *((const char *)reg + 1); /* Register address */ + buffer[7] = *((const char *)reg + 2); /* Register address */ + buffer[8] = *((const char *)reg + 3); /* Register address (LSB) */ + memcpy(&buffer[9], val, val_len); + + err = i2c_master_send(i2c, buffer, frame_len); + if (err != (int)frame_len) { + dev_err(&i2c->dev, "Writing to hub memory failed: %d\n", err); + goto error_kfree; + } + + buffer[0] = 0x99; /* Command (high byte) */ + buffer[1] = 0x37; /* Command (low byte) */ + buffer[2] = 0x00; /* Termination */ + frame_len = 3; + + err = i2c_master_send(i2c, buffer, frame_len); + if (err != (int)frame_len) { + dev_err(&i2c->dev, "Accessing configuration data failed: %d\n", err); + goto error_kfree; + } + + err = 0; + +error_kfree: + kfree(buffer); + return err; +} + +/* regmap puts address into data[0] .. data[3]; value is in data[4] */ +static int usb49xx_i2c_write(void *context, const void *data, size_t count) +{ + if (WARN_ON(count != 5)) + return -EINVAL; + + return usb49xx_i2c_gather_write(context, data, 4, data + 4, 1); +} + +static int usb49xx_i2c_read(void *context, const void *reg_buf, size_t reg_size, + void *val_buf, size_t val_size) +{ + struct i2c_client *i2c = (struct i2c_client *)context; + char *tx, *rx; + int err; + + if (WARN_ON(reg_size != 4)) { + err = -EINVAL; + goto error_return; + } + + tx = kmalloc(9, GFP_KERNEL); + if (!tx) { + err = -ENOMEM; + goto error_return; + } + + rx = kmalloc(1 + val_size, GFP_KERNEL); + if (!rx) { + err = -ENOMEM; + goto error_free_tx; + } + + tx[0] = 0x00; /* Memory address (high byte) */ + tx[1] = 0x00; /* Memory address (low byte) */ + tx[2] = 6; /* Number of bytes to write to memory */ + tx[3] = 0x01; /* Register Read */ + tx[4] = val_size; /* Read val_size data bytes */ + tx[5] = *((const char *)reg_buf + 0); /* Register address (MSB) */ + tx[6] = *((const char *)reg_buf + 1); /* Register address */ + tx[7] = *((const char *)reg_buf + 2); /* Register address */ + tx[8] = *((const char *)reg_buf + 3); /* Register address (LSB) */ + + err = i2c_master_send(i2c, tx, 9); + if (err != 9) { + dev_err(&i2c->dev, "Writing to hub memory failed: %d\n", err); + goto error_free_rx; + } + + tx[0] = 0x99; /* Command (high byte) */ + tx[1] = 0x37; /* Command (low byte) */ + tx[2] = 0x00; /* Termination */ + + err = i2c_master_send(i2c, tx, 3); + if (err != 3) { + dev_err(&i2c->dev, "Accessing configuration data failed: %d\n", err); + goto error_free_rx; + } + + /* Read from hub memory address 6 (according to application note) */ + tx[0] = 0x00; /* Memory address (high byte) */ + tx[1] = 0x06; /* Memory address (low byte) */ + + { + struct i2c_msg msgs[] = { + { + .addr = i2c->addr, .flags = 0, + .len = 2, .buf = tx + }, + { + .addr = i2c->addr, .flags = I2C_M_RD, + .len = 1 + val_size, .buf = rx + }, + }; + + err = i2c_transfer(i2c->adapter, msgs, ARRAY_SIZE(msgs)); + if (err < 0) { + dev_err(&i2c->dev, "Reading from hub memory failed: %d\n", err); + goto error_free_rx; + } + } + + WARN_ON(rx[0] < val_size); + + memcpy(val_buf, &rx[1], val_size); + + err = 0; + +error_free_rx: + kfree(rx); +error_free_tx: + kfree(tx); +error_return: + return err; +} + +/* + * The reason we need this custom regmap_bus instead of using regmap_init_i2c() + * is that accesses to the USB49xx configuration memory have to be wrapped into + * a special protocol. + */ +static const struct regmap_bus usb49xx_i2c_regmap = { + .write = usb49xx_i2c_write, + .gather_write = usb49xx_i2c_gather_write, + .read = usb49xx_i2c_read, + .max_raw_read = 8, + .max_raw_write = 128, +}; + +/* Avoid reading bigger dead ranges inside hubs memory. Same table for + * read and write. + */ +static const struct regmap_range usb49xx_regmap_yes_ranges[] = { + { .range_min = 0xBF800000, .range_max = 0xBF800003 }, + { .range_min = 0xBF800900, .range_max = 0xBF8009FF }, + { .range_min = 0xBF803000, .range_max = 0xBF803015 }, + { .range_min = 0xBF8030D0, .range_max = 0xBF803197 }, + { .range_min = 0xBF80398C, .range_max = 0xBF80398D }, + { .range_min = 0xBF803C00, .range_max = 0xBF803C3C }, + { .range_min = 0xBF8060CA, .range_max = 0xBF8060CC }, + { .range_min = 0xBF8064CA, .range_max = 0xBF8064CC }, + { .range_min = 0xBF8068CA, .range_max = 0xBF8068CC }, + { .range_min = 0xBF806CCA, .range_max = 0xBF806CCC }, + { .range_min = 0xBF8070CA, .range_max = 0xBF8070CC }, + { .range_min = 0xBF8074CA, .range_max = 0xBF8074CC }, + { .range_min = 0xBF8078CA, .range_max = 0xBF8078CC }, + + { .range_min = 0xBFD22856, .range_max = 0xBFD22857 }, + { .range_min = 0xBFD23202, .range_max = 0xBFD23472 }, +}; + +static const struct regmap_access_table usb49xx_regmap_access_table = { + .yes_ranges = usb49xx_regmap_yes_ranges, + .n_yes_ranges = ARRAY_SIZE(usb49xx_regmap_yes_ranges), +}; + +static int usb49xx_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id __always_unused) +{ + struct usb49xx *hub; + struct regmap_config regmap_cfg = { + .name = "usb49xx_config_mem", + .reg_bits = 32, + .val_bits = 8, + .wr_table = &usb49xx_regmap_access_table, + .rd_table = &usb49xx_regmap_access_table, + .can_multi_write = 1, + }; + + hub = devm_kzalloc(&i2c->dev, sizeof(struct usb49xx), GFP_KERNEL); + if (!hub) + return -ENOMEM; + + i2c_set_clientdata(i2c, hub); + hub->dev = &i2c->dev; + hub->i2c = i2c; + hub->regmap = devm_regmap_init(&i2c->dev, &usb49xx_i2c_regmap, i2c, + ®map_cfg); + if (IS_ERR(hub->regmap)) + return PTR_ERR(hub->regmap); + + return usb49xx_probe(hub); +} + +static int usb49xx_i2c_remove(struct i2c_client *i2c) +{ + struct usb49xx *hub = i2c_get_clientdata(i2c); + + usb49xx_reset(hub, 0); + + return 0; +}; + +static int __maybe_unused usb49xx_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct usb49xx *hub = i2c_get_clientdata(client); + + return regulator_disable(hub->vdd); +} + +static int __maybe_unused usb49xx_resume(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct usb49xx *hub = i2c_get_clientdata(client); + int err; + + err = regulator_enable(hub->vdd); + if (err) + return err; + + return usb49xx_connect(hub); +} + +static SIMPLE_DEV_PM_OPS(usb49xx_pm_ops, usb49xx_suspend, usb49xx_resume); + +static const struct i2c_device_id usb49xx_id[] = { + { "usb4712", 0 }, + { "usb4712i", 0 }, + { "usb4715", 0 }, + { "usb4715i", 0 }, + { "usb4912", 0 }, + { "usb4912i", 0 }, + { "usb4914", 0 }, + { "usb4914i", 0 }, + { "usb4916", 0 }, + { "usb4916 i", 0 }, + { "usb4925", 0 }, + { "usb4925i", 0 }, + { "usb4927", 0 }, + { "usb4927i", 0 }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(i2c, usb49xx_id); + +static struct i2c_driver usb49xx_i2c_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(usb49xx_of_match), + .pm = &usb49xx_pm_ops, + }, + .probe = usb49xx_i2c_probe, + .remove = usb49xx_i2c_remove, + .id_table = usb49xx_id, +}; + +module_i2c_driver(usb49xx_i2c_driver); + +MODULE_AUTHOR("Christian Eggers <ceggers@xxxxxxx>"); +MODULE_DESCRIPTION("USB47xx/USB49xx USB 2.0 Hub Controller Driver"); +MODULE_LICENSE("GPL"); -- Christian Eggers Embedded software developer Arnold & Richter Cine Technik GmbH & Co. Betriebs KG Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRA 57918 Persoenlich haftender Gesellschafter: Arnold & Richter Cine Technik GmbH Sitz: Muenchen - Registergericht: Amtsgericht Muenchen - Handelsregisternummer: HRB 54477 Geschaeftsfuehrer: Dr. Michael Neuhaeuser; Stephan Schenk; Walter Trauninger; Markus Zeiler
