This patch adds support for STUSB1600 USB Type-C port controller, used on
I2C4 on stm32mp15xx-dkx.
The default configuration on this board, on Type-C connector, is:
- Dual Power Role (DRP), so set power-role to "dual";
- Vbus limited to 500mA, so set power-opmode to "default" (it means 500mA
in USB 2.0).
power-opmode is used to reconfigure the STUSB1600 advertising of current
capability when its NVM is not in line with the board layout.
On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN (so add the
vin fixed 5V regulator too). So power operation mode depends on the power
supply used. To avoid any power issues, it is better to limit Vbus to 500mA
on this board.
ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and
signal is active low.
USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx
boards, so disconnection are not detected.
Without DWC2 usb-role-switch:
- if you unplug the USB cable from the Type-C port, you have to manually
disconnect the USB gadget:
echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
- Then you can plug the USB cable again in the Type-C port, and manually
reconnect the USB gadget:
echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected.
Signed-off-by: Amelie Delaunay <amelie.delaunay@xxxxxx>
---
No changes in v2.
---
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 7 +++++
arch/arm/boot/dts/stm32mp15xx-dkx.dtsi | 38 ++++++++++++++++++++++++
2 files changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 7eb858732d6d..55deaa52c3ee 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1574,6 +1574,13 @@
};
};
+ stusb1600_pins_a: stusb1600-0 {
+ pins {
+ pinmux = <STM32_PINMUX('I', 11, ANALOG)>;
+ bias-pull-up;
+ };
+ };
+
usart2_pins_a: usart2-0 {
pins1 {
pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
diff --git a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
index 70db923a45f7..8d55f3fd06b3 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
@@ -80,6 +80,14 @@
dais = <&sai2a_port &sai2b_port &i2s2_port>;
status = "okay";
};
+
+ vin: vin {
+ compatible = "regulator-fixed";
+ regulator-name = "vin";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
};
&adc {
@@ -230,6 +238,30 @@
/delete-property/dmas;
/delete-property/dma-names;
+ stusb1600@28 {
+ compatible = "st,stusb1600";
+ reg = <0x28>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpioi>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&stusb1600_pins_a>;
+ status = "okay";
+ vdd-supply = <&vin>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ power-opmode = "default";
+
+ port {
+ con_usbotg_hs_ep: endpoint {
+ remote-endpoint = <&usbotg_hs_ep>;
+ };
+ };
+ };
+ };
+
pmic: stpmic@33 {
compatible = "st,stpmic1";
reg = <0x33>;
@@ -599,6 +631,12 @@
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
+
+ port {
+ usbotg_hs_ep: endpoint {
+ remote-endpoint = <&con_usbotg_hs_ep>;
+ };
+ };
};
&usbphyc {
--
2.17.1
