Re: [PATCH v7 2/4] usb: dwc3: qcom: Add interconnect support in dwc3 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jul 07, 2020 at 10:41:24AM +0530, Sandeep Maheswaram (Temp) wrote:
> 
> On 7/1/2020 4:12 AM, Matthias Kaehlcke wrote:
> > On Tue, Jun 16, 2020 at 01:38:49PM -0700, Matthias Kaehlcke wrote:
> > > On Tue, Jun 16, 2020 at 10:22:47AM +0530, Sandeep Maheswaram (Temp) wrote:
> > > > On 6/16/2020 1:12 AM, Matthias Kaehlcke wrote:
> > > > > On Thu, Jun 04, 2020 at 04:16:31AM -0700, Stephen Boyd wrote:
> > > > > > Quoting Sandeep Maheswaram (Temp) (2020-06-04 02:43:09)
> > > > > > > On 6/3/2020 11:06 PM, Stephen Boyd wrote:
> > > > > > > > Quoting Sandeep Maheswaram (2020-03-31 22:15:43)
> > > > > > > > > diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> > > > > > > > > index 1dfd024..d33ae86 100644
> > > > > > > > > --- a/drivers/usb/dwc3/dwc3-qcom.c
> > > > > > > > > +++ b/drivers/usb/dwc3/dwc3-qcom.c
> > > > > > > > > @@ -285,6 +307,101 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
> > > > > > > > >            return 0;
> > > > > > > > >     }
> > > > > > > > > +
> > > > > > > > > +/**
> > > > > > > > > + * dwc3_qcom_interconnect_init() - Get interconnect path handles
> > > > > > > > > + * @qcom:                      Pointer to the concerned usb core.
> > > > > > > > > + *
> > > > > > > > > + */
> > > > > > > > > +static int dwc3_qcom_interconnect_init(struct dwc3_qcom *qcom)
> > > > > > > > > +{
> > > > > > > > > +       struct device *dev = qcom->dev;
> > > > > > > > > +       int ret;
> > > > > > > > > +
> > > > > > > > > +       if (!device_is_bound(&qcom->dwc3->dev))
> > > > > > > > > +               return -EPROBE_DEFER;
> > > > > > > > How is this supposed to work? I see that this was added in an earlier
> > > > > > > > revision of this patch series but there isn't any mention of why
> > > > > > > > device_is_bound() is used here. It would be great if there was a comment
> > > > > > > > detailing why this is necessary. It sounds like maximum_speed is
> > > > > > > > important?
> > > > > > > > 
> > > > > > > > Furthermore, dwc3_qcom_interconnect_init() is called by
> > > > > > > > dwc3_qcom_probe() which is the function that registers the device for
> > > > > > > > qcom->dwc3->dev. If that device doesn't probe between the time it is
> > > > > > > > registered by dwc3_qcom_probe() and this function is called then we'll
> > > > > > > > fail dwc3_qcom_probe() with -EPROBE_DEFER. And that will remove the
> > > > > > > > qcom->dwc3->dev device from the platform bus because we call
> > > > > > > > of_platform_depopulate() on the error path of dwc3_qcom_probe().
> > > > > > > > 
> > > > > > > > So isn't this whole thing racy and can potentially lead us to a driver
> > > > > > > > probe loop where the wrapper (dwc3_qcom) and the core (dwc3) are probing
> > > > > > > > and we're trying to time it just right so that driver for dwc3 binds
> > > > > > > > before we setup interconnects? I don't know if dwc3 can communicate to
> > > > > > > > the wrapper but that would be more of a direct way to do this. Or maybe
> > > > > > > > the wrapper should try to read the DT property for maximum speed and
> > > > > > > > fallback to a worst case high bandwidth value if it can't figure it out
> > > > > > > > itself without help from dwc3 core.
> > > > > > > > 
> > > > > > > This was added in V4 to address comments from Matthias in V3
> > > > > > > 
> > > > > > > https://patchwork.kernel.org/patch/11148587/
> > > > > > > 
> > > > > > Yes, that why I said:
> > > > > > 
> > > > > > "I see that this was added in an earlier
> > > > > >    revision of this patch series but there isn't any mention of why
> > > > > >    device_is_bound() is used here. It would be great if there was a comment
> > > > > >    detailing why this is necessary. It sounds like maximum_speed is
> > > > > >    important?"
> > > > > > 
> > > > > > Can you please respond to the rest of my email?
> > > > > I agree with Stephen that using device_is_bound() isn't a good option
> > > > > in this case, when I suggested it I wasn't looking at the big picture
> > > > > of how probing the core driver is triggered, sorry about that.
> > > > > 
> > > > > Reading the speed from the DT with usb_get_maximum_speed() as Stephen
> > > > > suggests would be an option, the inconvenient is that we then
> > > > > essentially require the property to be defined, while the core driver
> > > > > gets a suitable value from hardware registers. Not sure if the wrapper
> > > > > driver could read from the same registers.
> > > > > 
> > > > > One option could be to poll device_is_bound() for 100 ms (or so), with
> > > > > sleeps between polls. It's not elegant but would probably work if we
> > > > > don't find a better solution.
> > > > if (np)
> > > >          ret = dwc3_qcom_of_register_core(pdev);
> > > >      else
> > > >          ret = dwc3_qcom_acpi_register_core(pdev);
> > > > 
> > > >      if (ret) {
> > > >          dev_err(dev, "failed to register DWC3 Core, err=%d\n", ret);
> > > >          goto depopulate;
> > > >      }
> > > > 
> > > >      ret = dwc3_qcom_interconnect_init(qcom);
> > > >      if (ret)
> > > >          goto depopulate;
> > > > 
> > > >      qcom->mode = usb_get_dr_mode(&qcom->dwc3->dev);
> > > > 
> > > > Before calling dwc3_qcom_interconnect_init we are checking
> > > > 
> > > >      if (ret) {
> > > >          dev_err(dev, "failed to register DWC3 Core, err=%d\n", ret);
> > > >          goto depopulate;
> > > >      }
> > > > 
> > > > Doesn't  this condition confirm the core driver is probed?
> > > Not really:
> > > 
> > > // called under the hood by of_platform_populate()
> > > static int really_probe(struct device *dev, struct device_driver *drv)
> > > {
> > > 	...
> > > 
> > > 	if (dev->bus->probe) {
> > > 		ret = dev->bus->probe(dev);
> > > 		if (ret)
> > > 			goto probe_failed;
> > > 	} else if (drv->probe) {
> > > 		ret = drv->probe(dev);
> > > 	        if (ret)
> > > 	       		goto probe_failed;
> > >          }
> > > 
> > > 	...
> > > 
> > > probe_failed:
> > > 	...
> > > 
> > > 	/*
> > >           * Ignore errors returned by ->probe so that the next driver can try
> > >           * its luck.
> > >           */
> > >          ret = 0;
> > > 
> > > 	...
> > > 
> > > 	return ret;
> > > }
> > > 
> > > As a result of_platform_populate() in dwc3_qcom_of_register_core()
> > > returns 0 even when probing the device failed:
> > > 
> > > [    0.244339] dwc3-qcom a6f8800.usb: DBG: populate
> > > [    0.244772] dwc3 a600000.dwc3: DBG: dwc3_probe
> > > [    0.245237] dwc3 a600000.dwc3: DBG: dwc3_probe err: -517
> > > [    0.245264] dwc3-qcom a6f8800.usb: DBG: populate (done)
> > > [    0.245317] dwc3-qcom a6f8800.usb: DBG: dwc3_qcom_interconnect_init() failed: -517
> > > 
> > > Probe fails because the interconnect stuff isn't ready yet, otherwise
> > > it could access invalid data.
> > > 
> > > A later _populate() is successful and the probing of the core is done
> > > synchronously, i.e. after _populate() the core driver is fully
> > > initialized:
> > > 
> > > [    3.898106] dwc3-qcom a6f8800.usb: DBG: populate
> > > [    3.908356] dwc3 a600000.dwc3: DBG: dwc3_probe
> > > [    4.205104] dwc3 a600000.dwc3: DBG: dwc3_probe (done)
> > > [    4.210305] dwc3-qcom a6f8800.usb: DBG: populate (done)
> > > 
> > > The synchronous probing in _populate() suggests that using device_is_bound()
> > > would actually be a valid option, either the core device was successfully
> > > probed or not, there should be no race.
> > > 
> > > I sent a patch that adds this check to dwc3_qcom_of_register_core(), which
> > > is less confusing and makes clear that the core device is valid unless
> > > this function returns an error:
> > > 
> > >    https://lore.kernel.org/patchwork/patch/1257279/
> > > 
> > > It might make sense to add your "driver core:Export the symbol
> > > device_is_bound" patch, mine and this one to a single series.
> >  From the discussion on "driver core:Export the symbol device_is_bound"
> > (https://patchwork.kernel.org/patch/11584225/) it is clear that
> > this won't fly. The split dwc3 driver is considered a broken
> > design.
> > 
> > This is what Rob Herring said:
> > 
> >    We never should have had this split either in the DT binding nor
> >    driver(s) as if the SoC wrapper crap and licensed IP block are
> >    independent things. The thing to do here is either make the DWC3 code
> >    a library which drivers call (e.g. SDHCI) or add hooks into the DWC3
> >    driver for platform specifics (e.g. Designware PCI). Neither is a
> >    simple solution though.
> > 
> > That seems to be the desirable solution in the longer term, but it
> > doesn't seem reasonable to me to expect you to fix this design issue
> > to add interconnect support.
> > 
> > Some possible options to move forward:
> > 
> > - try to determine the max speed without involving the core device
> > - select a reasonable default when 'maximum-speed' is not specified
> > - use the core device to determine the max speed and pray
> 
> Can we do as below to get speed
> 
> qcom->max_speed = usb_get_maximum_speed(&qcom->dwc3->dev);

Yes, that would get the maximum speed from the DT if it is specified.
In case of USB_SPEED_UNKNOWN you probably want to assume it's
USB_SPEED_SUPER, which in the worst case would result in the ICC
running at a higher speed than needed.



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux