Hi Rob,
On 4/4/2020 10:47 PM, Rob Herring wrote:
On Thu, Mar 26, 2020 at 12:36:07PM +0530, Sandeep Maheswaram wrote:
Convert USB DWC3 bindings to DT schema format using json-schema.
Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/usb/qcom,dwc3.txt | 104 --------------
.../devicetree/bindings/usb/qcom,dwc3.yaml | 158 +++++++++++++++++++++
2 files changed, 158 insertions(+), 104 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.txt
create mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
new file mode 100644
index 0000000..0f69475
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@@ -0,0 +1,158 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+ - Manu Gautam <mgautam@xxxxxxxxxxxxxx>
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,msm8996-dwc3
+ - qcom,msm8998-dwc3
+ - qcom,sdm845-dwc3
+ - const: qcom,dwc3
+
+ reg:
+ description: Offset and length of register set for QSCRATCH wrapper
+ maxItems: 1
+
+ "#address-cells":
+ enum: [ 1, 2 ]
+
+ "#size-cells":
+ enum: [ 1, 2 ]
+
+ power-domains:
+ description: specifies a phandle to PM domain provider node
+ maxItems: 1
+
+ clocks:
+ description:
+ A list of phandle and clock-specifier pairs for the clocks
+ listed in clock-names.
+ items:
+ - description: System Config NOC clock.
+ - description: Master/Core clock, has to be >= 125 MHz
+ for SS operation and >= 60MHz for HS operation.
+ - description: System bus AXI clock.
+ - description: Mock utmi clock needed for ITP/SOF generation
+ in host mode. Its frequency should be 19.2MHz.
+ - description: Sleep clock, used for wakeup when
+ USB3 core goes into low power mode (U3).
+
+ clock-names:
+ items:
+ - const: cfg_noc
+ - const: core
+ - const: iface
+ - const: mock_utmi
+ - const: sleep
+
+ assigned-clocks:
+ items:
+ - description: Phandle and clock specifier of MOCK_UTMI_CLK.
+ - description: Phandle and clock specifoer of MASTER_CLK.
+
+ assigned-clock-rates:
+ maxItems: 2
Need to drop this as it is redundant. Soon this will generate an error.
Will do in next version.
+ items:
+ - description: Must be 19.2MHz (19200000).
Sounds like a constraint:
- const: 19200000
+ - description: Must be >= 60 MHz in HS mode, >= 125 MHz in SS mode.
- minimum: 60000000
maximum: ?
Tried as below but facing errors
assigned-clock-rates:
items:
- const: 19200000
- minimum: 60000000
maximum: 150000000
Errors
linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates: Additional items are not allowed
([150000000] was unexpected)
linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates:0: [19200000] is too short
linux-next/Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml:
usb@a6f8800: assigned-clock-rates: [[19200000], [150000000]] is too long
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: The interrupt that is asserted
+ when a wakeup event is received on USB2 bus.
+ - description: The interrupt that is asserted
+ when a wakeup event is received on USB3 bus.
+ - description: Wakeup event on DM line.
+ - description: Wakeup event on DP line.
+
+ interrupt-names:
+ items:
+ - const: hs_phy_irq
+ - const: ss_phy_irq
+ - const: dm_hs_phy_irq
+ - const: dp_hs_phy_irq
+
+ qcom,select-utmi-as-pipe-clk:
+ description:
+ If present, disable USB3 pipe_clk requirement.
+ Used when dwc3 operates without SSPHY and only
+ HS/FS/LS modes are supported.
+ type: boolean
+
+# Required child node:
+
+patternProperties:
+ "^dwc3@[0-9a-f]+$":
+ type: object
+ description:
+ A child node must exist to represent the core DWC3 IP block
+ The content of the node is defined in dwc3.txt.
+
+required:
+ - compatible
+ - reg
+ - "#address-cells"
+ - "#size-cells"
+ - power-domains
+ - clocks
+ - clock-names
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ usb@a6f8800 {
+ compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ dwc3@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xcd00>;
You need 'ranges' in the parent for this address to be translatable.
Will add in next version.
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x740 0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
