The Fintek F81534A series is contains 1 HUB / 1 GPIO device / n UARTs,
but the UART is default disable and need enabled by GPIO device(2c42/16F8).
When F81534A plug to host, we can only see 1 HUB & 1 GPIO device and we
write 0x8fff to GPIO device register F81534A_CTRL_CMD_ENABLE_PORT(116h)
to enable all available serial ports.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@xxxxxxxxx>
---
Changelog:
v3:
1. Modify some define with prefix F81534A_CTRL_.
2. Use kmemdup() in f81534a_ctrl_set_register().
3. Not accpet with short transfers in f81534a_ctrl_set_register().
4. Add comment in f81534a_ctrl_enable_all_ports() to describe magic
constants.
5. Remove non-need usb_get_dev()/usb_put_dev().
6. Add F81534A_CTRL_ID in MODULE_DEVICE_TABLE().
v2:
1: Simplify the generator behavior.
2: Change multiply MODULE_DEVICE_TABLE() to 1 only.
drivers/usb/serial/f81232.c | 134 +++++++++++++++++++++++++++++++++++-
1 file changed, 133 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
index 21410a7f3a8b..0303f94b2521 100644
--- a/drivers/usb/serial/f81232.c
+++ b/drivers/usb/serial/f81232.c
@@ -36,6 +36,9 @@
{ USB_DEVICE(0x2c42, 0x1635) }, /* 8 port UART device */ \
{ USB_DEVICE(0x2c42, 0x1636) } /* 12 port UART device */
+#define F81534A_CTRL_ID \
+ { USB_DEVICE(0x2c42, 0x16f8) } /* Global control device */
+
static const struct usb_device_id f81232_id_table[] = {
F81232_ID,
{ } /* Terminating entry */
@@ -46,9 +49,15 @@ static const struct usb_device_id f81534a_id_table[] = {
{ } /* Terminating entry */
};
+static const struct usb_device_id f81534a_ctrl_id_table[] = {
+ F81534A_CTRL_ID,
+ { } /* Terminating entry */
+};
+
static const struct usb_device_id combined_id_table[] = {
F81232_ID,
F81534A_SERIES_ID,
+ F81534A_CTRL_ID,
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, combined_id_table);
@@ -61,6 +70,7 @@ MODULE_DEVICE_TABLE(usb, combined_id_table);
#define F81232_REGISTER_REQUEST 0xa0
#define F81232_GET_REGISTER 0xc0
#define F81232_SET_REGISTER 0x40
+#define F81534A_ACCESS_REG_RETRY 2
#define SERIAL_BASE_ADDRESS 0x0120
#define RECEIVE_BUFFER_REGISTER (0x00 + SERIAL_BASE_ADDRESS)
@@ -92,6 +102,8 @@ MODULE_DEVICE_TABLE(usb, combined_id_table);
#define F81534A_TRIGGER_MULTIPLE_4X BIT(3)
#define F81534A_FIFO_128BYTE (BIT(1) | BIT(0))
+#define F81534A_MAX_PORT 12
+
/* Serial port self GPIO control, 2bytes [control&output data][input data] */
#define F81534A_GPIO_REG 0x10e
#define F81534A_GPIO_MODE2_DIR BIT(6) /* 1: input, 0: output */
@@ -101,6 +113,9 @@ MODULE_DEVICE_TABLE(usb, combined_id_table);
#define F81534A_GPIO_MODE1_OUTPUT BIT(1)
#define F81534A_GPIO_MODE0_OUTPUT BIT(0)
+#define F81534A_CTRL_CMD_ENABLE_PORT 0x116
+
+
struct f81232_private {
struct mutex lock;
u8 modem_control;
@@ -848,6 +863,89 @@ static void f81232_lsr_worker(struct work_struct *work)
dev_warn(&port->dev, "read LSR failed: %d\n", status);
}
+static int f81534a_ctrl_set_register(struct usb_device *dev, u16 reg, u16 size,
+ void *val)
+{
+ int retry = F81534A_ACCESS_REG_RETRY;
+ int status;
+ u8 *tmp;
+
+ tmp = kmemdup(val, size, GFP_KERNEL);
+ if (!tmp)
+ return -ENOMEM;
+
+ while (retry--) {
+ status = usb_control_msg(dev,
+ usb_sndctrlpipe(dev, 0),
+ F81232_REGISTER_REQUEST,
+ F81232_SET_REGISTER,
+ reg,
+ 0,
+ tmp,
+ size,
+ USB_CTRL_SET_TIMEOUT);
+ if (status != size) {
+ status = usb_translate_errors(status);
+ if (status == -EIO)
+ continue;
+
+ status = -EIO;
+ } else {
+ status = 0;
+ }
+
+ break;
+ }
+
+ if (status) {
+ dev_err(&dev->dev, "set ctrl reg: %x, failed status: %d\n",
+ reg, status);
+ }
+
+ kfree(tmp);
+ return status;
+}
+
+static int f81534a_ctrl_enable_all_ports(struct usb_interface *intf)
+{
+ struct usb_device *dev = interface_to_usbdev(intf);
+ unsigned char enable[2];
+ int status;
+
+ /*
+ * Enable all available serial ports, define as following:
+ * bit 15 : Reset behavior (when HUB got soft reset)
+ * 0: maintain all serial port enabled state.
+ * 1: disable all serial port.
+ * bit 0~11 : Serial port enable bit.
+ */
+ enable[0] = 0xff;
+ enable[1] = 0x8f;
+
+ status = f81534a_ctrl_set_register(dev, F81534A_CTRL_CMD_ENABLE_PORT,
+ sizeof(enable), enable);
+ if (status)
+ dev_warn(&dev->dev, "set ENABLE_PORT failed: %d\n", status);
+
+ return status;
+}
+
+static int f81534a_ctrl_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
+{
+
+ return f81534a_ctrl_enable_all_ports(intf);
+}
+
+static void f81534a_ctrl_disconnect(struct usb_interface *intf)
+{
+}
+
+static int f81534a_ctrl_resume(struct usb_interface *intf)
+{
+ return f81534a_ctrl_enable_all_ports(intf);
+}
+
static int f81232_port_probe(struct usb_serial_port *port)
{
struct f81232_private *priv;
@@ -975,7 +1073,41 @@ static struct usb_serial_driver * const serial_drivers[] = {
NULL,
};
-module_usb_serial_driver(serial_drivers, combined_id_table);
+static struct usb_driver f81534a_ctrl_driver = {
+ .name = "f81534a_ctrl",
+ .id_table = f81534a_ctrl_id_table,
+ .probe = f81534a_ctrl_probe,
+ .disconnect = f81534a_ctrl_disconnect,
+ .resume = f81534a_ctrl_resume,
+};
+
+static int __init f81232_init(void)
+{
+ int status;
+
+ status = usb_register_driver(&f81534a_ctrl_driver, THIS_MODULE,
+ KBUILD_MODNAME);
+ if (status)
+ return status;
+
+ status = usb_serial_register_drivers(serial_drivers, KBUILD_MODNAME,
+ combined_id_table);
+ if (status) {
+ usb_deregister(&f81534a_ctrl_driver);
+ return status;
+ }
+
+ return 0;
+}
+
+static void __exit f81232_exit(void)
+{
+ usb_serial_deregister_drivers(serial_drivers);
+ usb_deregister(&f81534a_ctrl_driver);
+}
+
+module_init(f81232_init);
+module_exit(f81232_exit);
MODULE_DESCRIPTION("Fintek F81232/532A/534A/535/536 USB to serial driver");
MODULE_AUTHOR("Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>");
--
2.17.1
