V1:
This series enables the Primary and Secondary USB controllers on the
QCS404, associated PHYs, role-switching and DTS descriptions.
The series takes in a number of patches worked on by a number of people
over the past few years from downstream, through to previous upstream
submissions for both of these interfaces. Additional work has been done to
enable USB role-switching.
1. USB SS
- extcon has been dropped in favour of gpio-usb-conn as discussed and
agreed previously by Jorge, Bjorn, Stephen Boyd and Jack Pham [1].
- Regulator API has been updated following suggestions from Bjorn.
- Sanitzation of the DT compatible name - dropped "snps" entirely
from the name - it made almost no sense to me and doesn't appear
consistent with similar naming conventions for Snopsys based IP.
2. USB HS
- Regulator API changes here.
- Dropped "snps" from the namespace for similar reasons as above.
- Dropped "28nm" from the namespace, looked superfluous.
- Changed "High-Speed" to "Hi-Speed".
- [2]
3. DWC3 Role switching
- At the time usb-gpio-conn was discussed it was mentioned that
role-switching was absent from the DWC3 driver.
- John Stultz has some patches in-flight for that, that I've included in
this series for completeness.
- Adds my SoB to relevant patches.
- Drops gerrit ChangeId.
4. DWC3 usb-gpio-conn
Needs to be a child node of the DWC3 driver so some code and DT binding
is required for that.
5. QCOM-DWC3
Since we are role-switching with an external PMIC supplying VBUS we want
to skip past toggling VBUS from QCOM-DWC3 controlled registers, so a
patch is added to the qcom-dwc3 driver to do that.
References:
1: USB SS PHY for Qualcomm's QCS404
https://lwn.net/ml/devicetree/20190207111734.24171-1-jorge.ramirez-ortiz@xxxxxxxxxx/
2: Add Synopsys High-Speed USB PHY driver for Qualcomm SoCs
https://lore.kernel.org/linux-arm-msm/20181127100722.9993-3-shawn.guo@xxxxxxxxxx/
https://www.spinics.net/lists/linux-usb/msg190003.html
V2:
- Fixes yaml error - Rob's YAML robot
- Exclusive control of reset in PHY drivers - Philipp Zabel
Bjorn Andersson (1):
arm64: dts: qcom: qcs404: Add USB devices and PHYs
Bryan O'Donoghue (10):
dt-bindings: usb: dwc3: Add a gpio-usb-connector description
usb: dwc3: qcom: Override VBUS when using gpio_usb_connector
usb: dwc3: Add support for usb-conn-gpio connectors
arm64: dts: qcom: qcs404-evb: Define VBUS detect pin
arm64: dts: qcom: qcs404-evb: Define VBUS boost pin
arm64: dts: qcom: qcs404-evb: Define USB ID pin
arm64: dts: qcom: qcs404-evb: Describe external VBUS regulator
arm64: dts: qcom: qcs404-evb: Raise vreg_l12_3p3 minimum voltage
arm64: dts: qcom: qcs404-evb: Enable secondary USB controller
arm64: dts: qcom: qcs404-evb: Enable primary USB controller
John Stultz (2):
dt-bindings: usb: generic: Add role-switch-default-mode binding
usb: dwc3: Add support for role-switch-default-mode binding
Jorge Ramirez-Ortiz (3):
dt-bindings: phy: remove qcom-dwc3-usb-phy
dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
phy: qualcomm: usb: Add SuperSpeed PHY driver
Shawn Guo (1):
phy: qualcomm: Add Synopsys Hi-Speed USB PHY driver
Sriharsha Allenki (1):
dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding
Yu Chen (1):
usb: dwc3: Registering a role switch in the DRD code.
.../bindings/phy/qcom,qcs404-usb-hs.yaml | 77 ++++
.../devicetree/bindings/phy/qcom,usb-ss.yaml | 75 ++++
.../bindings/phy/qcom-dwc3-usb-phy.txt | 37 --
.../devicetree/bindings/usb/dwc3.txt | 11 +
.../devicetree/bindings/usb/generic.txt | 6 +
arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 90 +++-
arch/arm64/boot/dts/qcom/qcs404.dtsi | 100 +++++
drivers/phy/qualcomm/Kconfig | 21 +
drivers/phy/qualcomm/Makefile | 2 +
drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c | 415 ++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-usb-ss.c | 246 +++++++++++
drivers/usb/dwc3/core.h | 6 +
drivers/usb/dwc3/drd.c | 123 +++++-
drivers/usb/dwc3/dwc3-qcom.c | 17 +-
14 files changed, 1184 insertions(+), 42 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,qcs404-usb-hs.yaml
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml
delete mode 100644 Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
create mode 100644 drivers/phy/qualcomm/phy-qcom-qcs404-usb-hs.c
create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-ss.c
--
2.25.0
