On 2019/11/26 21:11, Neil Armstrong wrote:
> On 25/11/2019 23:02, Martin Blumenstingl wrote:
>> Hi Hanjie,
>>
>> On Mon, Nov 25, 2019 at 8:53 AM Hanjie Lin <hanjie.lin@xxxxxxxxxxx> wrote:
>>>
>>>
>>>
>>> On 2019/11/22 15:52, Martin Blumenstingl wrote:
>>>> Hello Hanjie,
>>>>
>>>> On Fri, Nov 22, 2019 at 7:55 AM Hanjie Lin <hanjie.lin@xxxxxxxxxxx> wrote:
>>>> [...]
>>>>> dt-bindings: phy: Add Amlogic G12A USB2 PHY Bindings
>>>>> dt-bindings: usb: dwc3: Add the Amlogic A1 Family DWC3 Glue Bindings
>>>>> phy: amlogic: Add Amlogic A1 USB2 PHY Driver
>>>> drivers/phy/amlogic/phy-meson-g12a-usb2.c seems very similar to the A1
>>>> USB2 PHY you are introducing here.
>>>>
>>>>> usb: dwc3: Add Amlogic A1 DWC3 glue
>>>> drivers/usb/dwc3/dwc3-meson-g12a.c is also very similar to the dwc3 glue.
>>>>
>>>> I have two questions:
>>>> - how is the PHY and the dwc3 glue different from G12A (or SM1)?
>>>> - why do we need a separate set of new drivers (instead of updating
>>>> the existing drivers)?
>>>>
>>>> We try to use one driver for the same IP block, even if there are
>>>> several revisions with small differences (for example the SAR ADC
>>>> driver supports all SoC generations from Meson8 to G12A/G12B/SM1,
>>>> because 80-90% of the code is shared across all revisions).
>>>>
>>>>
>>>> Martin
>>>>
>>>> .
>>>>
>>>
>>> Hi Martin,
>>>
>>> thanks for the comment.
>>>
>>> 1, G12A have usb2-phy0/usb2-phy1/usb3-phy0 three phys and an interrupt to support host/peripheral/otg modes.
>>> A1 has one usb2-phy0 phy and only support host mode.
>> dwc3-meson-g12a treats PHYs as optional
>> so if you only pass "usb2-phy0" and skip usb2-phy1/usb3-phy0 then it
>> will still work fine
>> (I didn't check whether the binding also reflects this)
>
> Exact, a simple match data could make max-phys to 1 for A1.
>
>>
>>> 2, G12A glue/phy drivers are for G12A SoCs, there are some diffrences to A1.
>>> G12A glue driver have dr_mode and interrupts two attributes to support otg mode while A1 hasn't this requirement.
>> dwc3-meson-g12a ignores the interrupt for HOST-only mode
>> (I didn't check whether the IRQ is optional in the dt-binding)
>
> Interrupt support and OTG manual switch is optional and can be easily bypassed.
>
>>
>>> G12A glue driver has a hard coding vbus regulator code to support otg mode while A1 hasn't this requirement.
>> my understanding is that whether a board has a VBUS regulator depends
>> on the board design. it has nothing to do with the SoC itself
>>
>>> G12A glue driver has a hard coding support phys while A1 only supports host mode.
>>> enum {
>>> USB2_HOST_PHY = 0,
>>> USB2_OTG_PHY,
>>> USB3_HOST_PHY,
>>> PHY_COUNT,
>>> };
>> this goes together with comment #1 - you can skip USB2_OTG_PHY and
>> USB3_HOST_PHY and the driver should still work fine
>
> Exact
>
>>
>>> G12A glue driver only supports one clock while A1 needs four clocks.
>> indeed, the dwc3-meson-g12a needs to be updated to support this
>> I don't think that I have used it myself yet but there's the
>> clk_bulk_data framework
>> it seems to fit this use-case pretty well: define an arbitrary number
>> of clocks for G12A/B an another set of clocks for A1 - then use the
>> clk_bulk_data framework to enable/disable them all at once
>
> Exact, a simple conversion to clk_bulk_* would be enough
>
>>
>>> G12A and A1 phy drivers have different register configurations since hardware differences.
>> other drivers have similar requirements: (mostly) identical register
>> layout but different values per SoC
>> here are two examples (I'm not sure if they are good examples though):
>> Lantiq/Intel SoC [0] and Allwinner SoCs [1]
>>
>> I compared your driver with phy-meson-g12a-usb2 and only found four differences:
>> 1) PHY_CTRL_R18_MPLL_DCO_CLK_SEL is set for A1
>> 2) PHY_CTRL_R13_UPDATE_PMA_SIGNALS is not set for A1
>> 3) PHY_CTRL_R21 is updated twice for A1 (once for earlier gen SoCs)
>> 4) A1 doesn't reference the "xtal" clock
>>
>> Difference 4) seems to be a general problem because there seems to be
>> a PLL inside the PHY registers and that PLL must be fed by some input
>> clock
>> So I believe that there is some clock input (which is currently
>> missing from your A1 USB2 PHY driver)
>
> These differences are trivial to add with a match data structure.
>
>>
>>> 3, We have estimated these differences and we thought it's more clear and readable to have a dedicated glue/phy
>>> driver for A1 SoCs, so also dedicated dt-bindings.
>> I think we should separate the driver and dt-bindings
>>
>> Based on what I have seen so far my preference for the PHY is:
>> - use the existing dt-binding, because it seems to be the same IP
>> block with different register configuration
>> - use the existing driver because there are only three different
>> register values (to me it feels like a dedicated driver for these
>> means more overhead for little benefit)
>>
>> for the glue I think:
>> - extend the existing dt-bindings and make some of the PHYs and the
>> interrupt line optional. making the PHYs optional will be needed when
>> adding GXL/GXM/AXG support anyways
>> - use the existing driver and make the clock inputs depend on the SoC
>> - everything else should already work as is
>>
>> please let me know if I missed something:
>> comparing/reviewing the new and existing drivers is harder than just
>> copying the existing one and modifying that copy
>> (this is one of the reasons why I think that duplicating code makes
>> the drivers harder to maintain)
>>
>> I also thought about the negative consequences of extending the
>> existing driver(s).
>> modifying the existing code could break the driver for existing boards.
>> however, I think that is not a problem because BayLibre's Kernel CI
>> labs have good coverage for G12A, G12B and SM1.
>> so if you add some A1 boards there (or host your own lab with A1
>> boards) any breakage will be found early (the Kernel CI bot even does
>> git bisect and sends emails)
> The overall architecture is the same since the GXL SoCs, we also plan to
> move the GXL/GXM USB complex into the G12A usb-ctrl driver because the architecture
> is very similar.
>
> For A1, the changes will be quite minimal, please try and post a RFC version so we
> can evaluate.
>
> Thanks,
>
> Neil
>
>>
>>
>> Martin
>>
>>
>> [0] https://github.com/torvalds/linux/blob/d2912cb15bdda8ba4a5dd73396ad62641af2f520/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c#L47
>> [1] https://github.com/torvalds/linux/blob/c942fddf8793b2013be8c901b47d0a8dc02bf99f/drivers/phy/allwinner/phy-sun4i-usb.c#L862
>>
>
> .
>
Hi Neil:
Okay.
We will try to move A1 usb phy/ctrl driver into G12A driver and send a V2 patch later.
Thanks.
