* Tony Lindgren <tony@xxxxxxxxxxx> [190927 15:20]:
> * Yegor Yefremov <yegorslists@xxxxxxxxxxxxxx> [190927 12:31]:
> > On Fri, Sep 27, 2019 at 10:18 AM Yegor Yefremov
> > <yegorslists@xxxxxxxxxxxxxx> wrote:
> > >
> > > I was porting my system from 3.18/4.2 to 5.3. During this process I
> > > noticed that FT4232 that is attached directly to musb is not working
> > > correctly when opened for the first time: tx is working but nothing
> > > can be received. On the second opening everything is working fine.
> > > When the same chip is connected via a USB hub - everything is working
> > > from the very beginning.
> > >
> > > I could reproduce this issue using BeagleBone Black with omap2plus_defconfig.
> > >
> > > # lsusb -t
> > > +/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M
> > > |__ Port 1: Dev 2, If 0, Class=, Driver=ftdi_sio, 480M
> > > |__ Port 1: Dev 2, If 1, Class=, Driver=ftdi_sio, 480M
> > > |__ Port 1: Dev 2, If 2, Class=, Driver=ftdi_sio, 480M
> > > |__ Port 1: Dev 2, If 3, Class=, Driver=ftdi_sio, 480M
> > >
> > > git bisect revealed the following:
> > >
> > > fdea2d09b997ba4c86e7a707a5fac87c305f2131 is the first bad commit
> > > commit fdea2d09b997ba4c86e7a707a5fac87c305f2131
> > > Author: Tony Lindgren <tony@xxxxxxxxxxx>
> > > Date: Wed Aug 31 07:19:59 2016 -0700
> > >
> > > dmaengine: cppi41: Add basic PM runtime support
> > >
> > > Let's keep the device enabled between cppi41_dma_issue_pending()
> > > and dmaengine_desc_get_callback_invoke() and rely on the PM runtime
> > > autoidle timeout elsewhere.
> > >
> > > As the PM runtime is for whole device, not for each channel,
> > > we need to queue pending transfers if the device is PM runtime
> > > suspended. Then we start the pending transfers in PM runtime
> > > resume.
> > >
> > > Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> > > Signed-off-by: Vinod Koul <vinod.koul@xxxxxxxxx>
> > >
> > > :040000 040000 8cf92c09083541dfdee01cc2973e73ef520f4fb1
> > > a03c1a7ba8e723f7b503733c46edaa4141483265 M drivers
> > >
> > > Any idea?
> >
> > The problems can be reproduced with other FTDI chips like FT232R.
> >
> > Invoking "minicom -D /dev/ttyUSB0" and typing some characters is
> > enough to reproduce the issue (just in case, hw flow control should be
> > disabled).
> >
> > cp210x based converter is working without an issue. So only FTDI chips
> > are affected so far.
>
> Hmm OK. Maybe this could be an issue where the FTDI chip takes
> longer to enumerate and cppi41 is already suspended by then?
>
> At least we had a similar issue with commit ae4a3e028bb8
> ("dmaengine: cppi41: Fix runtime PM timeouts with USB mass
> storage").
Looks like I'm unable to reproduce this with bbb and FT232R
USB UART.
I tried v5.3 with omap2plus_defconfig, then boot, load musb
and ftdi-sio modules, then connect ftdi directly to bbb,
and then run "minicom -D /dev/ttyUSB0" on bbb and it works
just fine for me.
I tried also rebooting the device inbetween in case it only
happens on the first connect after boot but still no luck
reproducing.
Maybe try adding some debug prints to cppi41_runtime_suspend()
and cppi41_runtime_resume() to see if gets runtime suspended
too early?
Regards,
Tony
