Hi Greg,
On Monday, September 23, 2019 19:07, Greg Kroah-Hartman wrote:
>
> On Mon, Sep 23, 2019 at 06:51:02PM +0800, Ran Wang wrote:
> > USB 2.0 Embedded Host PET Automated Test (CH6) 6.7.23 A-UUT
> > "Unsupported Device" Message require to stop enumerating device with
> > VID=0x1a0a PID=0x0201 and pop message to declare this device is not
> supported.
>
> Why is this a requirement?
This comes from <USB On-The-Go and Embedded Host Automated Compliance Plan
for the On-The-Go& Embedded Host Supplement Revision2.0>
Below is related description I quote from it:
6.7.23 A-UUT "Unsupported Device" Message
Purpose: This test verifies that an A-UUT produces a device non-supported error message
when a device it doesn't recognize, and does not support HNP, connects to it.
Applies to: All Targeted Hosts
Description: Get VBUS turned on, and connect to the A-UUT. Get enumerated and respond
as an unknown device not supporting HNP. Check that a suitable error message is generated.
Pass Criteria: Message "Unsupported Device"or similar is displayed on UUT
6.7.23.1 Test Procedure
1. Start with cable still attached, PET applying 10μF capacitance and 10kΩ pull-down
resistance between VBUS and ground, data lines not pulled up.
2. Get VBUS turned on, using the method described in Section6.7.1.
3. Wait for almost TB_SVLD_BCON max (1s - 0.1s = 0.9s) from VBUS reaching VOTG_SESS_VLD max.
4. Connect PET using D+ pull-up.
5. Allow A-UUT to enumerate PET, responding with a VID / PID combination not on the TPL
of the UUT and also with the OTG descriptor stating that it does not support HNP.
6. Start 30s timer when Device Descriptor is read.
7. Display Message "Click OK if 'Unsupported Device' indication displayed on UUT".
8. If operator clicks OK before 30s timer expires, then UUT passes test.
9. If 30selapses first, then UUT fails test.
10. PET disconnects by removing any termination on the data lines, but leaves a capacitance of
10μF and a pull-down resistance of 10kΩ connected across VBUS.
11. Wait 2s to allow disconnection to be detected.
End of Test.
> And why those specific vid/pid values? What do they refer to?
For step 5, we got the VID / PID number from USB IF certified lab(Allion.inc at Taiwang). Looks like
this is a reserved ID pair and will not be allocated to any vendor for their products. So it's hence used for this
case test (like saying: you should be able to pop a not-support message for this reserved VID&PID).
> >
> > Signed-off-by: Ran Wang <ran.wang_1@xxxxxxx>
> > ---
> > drivers/usb/core/hub.c | 12 ++++++++++++
> > 1 file changed, 12 insertions(+)
> >
> > diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index
> > bbcfa63..3cda0da 100644
> > --- a/drivers/usb/core/hub.c
> > +++ b/drivers/usb/core/hub.c
> > @@ -4982,6 +4982,18 @@ static void hub_port_connect(struct usb_hub *hub,
> int port1, u16 portstatus,
> > if (status < 0)
> > goto loop;
> >
> > + /* USB 2.0 Embedded Host PET Automated Test (CH6)
> > + * 6.7.23 A-UUT "Unsupported Device" Message
> > + * require to filter out below device when enumeration
> > + */
>
> Nit, can you align your comment lines, to match the other multi-line comments
> in this file? Otherwise it starts to look bad over time.
Yes, will update.
>
>
> > + if ((udev->descriptor.idVendor == 0x1a0a)
> > + && (udev->descriptor.idProduct == 0x0201)) {
>
> Are you sure you don't have to convert this value into cpu endian before
> checking it?
Thanks for pointing out, how about this:
if ((le16_to_cpu(udev->descriptor.idVendor) == 0x1a0a)
&& (le16_to_cpu(udev->descriptor.idProduct) == 0x0201)) {
Regards,
Ran
