Hi Carsten, Thanks for your reply. I though CONFIG_PM covers CPU only (but now I am compiling kernel with PM completely). Occasionally we see crash at boot too without even reaching stage of loading xhci-pci.ko driver. Log is below. Is this can be because of again uPD connected on PCIe bus (through PCIe switch)? barebox 2017.12.0-bsp-yocto-i.mx6-pd18.1.1 #1 Thu Jul 25 13:13:48 UTC 2019 Board: Phytec phyCORE-i.MX6 Quad with eMMC detected i.MX6 Quad revision 1.5 i.MX6 unique ID: ee7f9502211821d4 mdio_bus: miibus0: probed eth0: got preset MAC address: 50:2d:f4:15:a9:fe m25p80 flash@00: n25q128a13 (16384 Kbytes) imx-usb 2184200.usb: USB EHCI 1.00 imx-esdhc 2190000.usdhc: registered as 2190000.usdhc imx-esdhc 219c000.usdhc: registered as 219c000.usdhc da9063 da90620: da9062 with id 62.22.ff.1a detected state: New state registered 'state' state: Using bucket 0@0x00000000 netconsole: registered as netconsole-1 phySOM-i.MX6: Using environment in MMC malloc space: 0x4fefb480 -> 0x8fdf68ff (size 1023 MiB) mmc3: detected MMC card version 5.0 mmc3: registered mmc3.boot0 mmc3: registered mmc3.boot1 mmc3: registered mmc3 running /env/bin/init... Hit m for menu or any other key to stop autoboot: 1 bootchooser: Target list $global.bootchooser.targets is empty Nothing bootable found on 'bootchooser' booting 'emmc' Loading ARM Linux zImage '/mnt/emmc/zImage' Loading devicetree from '/mnt/emmc/oftree' m25p0: Cannot find nodepath /soc/aips-bus@02000000/spba-bus@02000000/ecspi@02008000/flash@0, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f4: Invalid argument at24 24c320: Cannot find nodepath /soc/aips-bus@02100000/i2c@021a8000/eeprom@50, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f4: Invalid argument Failed to fixup node in of_state_fixup+0x1/0x1f8: No such device mmc3: Cannot find nodepath /soc/aips-bus@02100000/usdhc@0219c000, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f4: Invalid argument commandline: console=ttymxc1,115200n8 root=/dev/mmcblk1p2 rootwait rw Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.2.7-bsp-yocto-i.mx6-pd18.1.1 (flateef@flateef-XPS-13-9360) (gcc version 8.2.0 (Buildroot 2018.11.4-gebef590b)) #1 SMP Fri Aug 9 01:40:51 CEST 2019 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: PHYTEC phyBOARD-Mira Quad full featured with eMMC [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 128 MiB at 0x38000000 [ 0.000000] percpu: Embedded 16 pages/cpu s34764 r8192 d22580 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/mmcblk1p2 rootwait rw [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1934212K/2097152K available (8192K kernel code, 365K rwdata, 2628K rodata, 1024K init, 400K bss, 31868K reserved, 131072K cma-reserved, 1309804K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] random: get_random_bytes called from start_kernel+0x250/0x424 with crng_init=0 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000014] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000045] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002929] Console: colour dummy device 80x30 [ 0.002992] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003020] pid_max: default: 32768 minimum: 301 [ 0.003305] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003346] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004458] CPU: Testing write buffer coherency: ok [ 0.004517] CPU0: Spectre v2: using BPIALL workaround [ 0.004985] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006111] Setting up static identity map for 0x10100000 - 0x10100078 [ 0.006389] rcu: Hierarchical SRCU implementation. [ 0.007121] smp: Bringing up secondary CPUs ... [ 0.008372] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.008384] CPU1: Spectre v2: using BPIALL workaround [ 0.009974] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.009986] CPU2: Spectre v2: using BPIALL workaround [ 0.011430] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.011442] CPU3: Spectre v2: using BPIALL workaround [ 0.011668] smp: Brought up 1 node, 4 CPUs [ 0.011692] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.011706] CPU: All CPU(s) started in SVC mode. [ 0.013443] devtmpfs: initialized [ 0.031486] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.031960] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.031999] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.044743] pinctrl core: initialized pinctrl subsystem [ 0.046494] NET: Registered protocol family 16 [ 0.060588] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.061412] audit: initializing netlink subsys (disabled) [ 0.061745] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.062760] CPU identified as i.MX6Q, silicon rev 1.5 [ 0.074287] vdd1p1: supplied by regulator-dummy [ 0.075185] vdd3p0: supplied by regulator-dummy [ 0.076039] vdd2p5: supplied by regulator-dummy [ 0.098019] No ATAGs? [ 0.098256] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.098280] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.100851] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.155153] mxs-dma 110000.dma-apbh: initialized [ 0.163489] SCSI subsystem initialized [ 0.164302] usbcore: registered new interface driver usbfs [ 0.164405] usbcore: registered new interface driver hub [ 0.164564] usbcore: registered new device driver usb [ 0.167207] i2c i2c-0: IMX I2C adapter registered [ 0.168137] i2c i2c-1: IMX I2C adapter registered [ 0.169506] i2c i2c-2: IMX I2C adapter registered [ 0.169852] pps_core: LinuxPPS API ver. 1 registered [ 0.169870] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx> [ 0.169912] PTP clock support registered [ 0.171200] Bluetooth: Core ver 2.22 [ 0.171280] NET: Registered protocol family 31 [ 0.171297] Bluetooth: HCI device and connection manager initialized [ 0.171323] Bluetooth: HCI socket layer initialized [ 0.171346] Bluetooth: L2CAP socket layer initialized [ 0.171386] Bluetooth: SCO socket layer initialized [ 0.172256] clocksource: Switched to clocksource mxc_timer1 [ 0.172507] VFS: Disk quotas dquot_6.6.0 [ 0.172647] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.189291] NET: Registered protocol family 2 [ 0.190486] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.190545] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.190711] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.190978] TCP: Hash tables configured (established 8192 bind 8192) [ 0.191318] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.191399] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.191909] NET: Registered protocol family 1 [ 0.192938] RPC: Registered named UNIX socket transport module. [ 0.192958] RPC: Registered udp transport module. [ 0.192973] RPC: Registered tcp transport module. [ 0.192988] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.193014] PCI: CLS 0 bytes, default 64 [ 0.194260] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.194654] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.197613] Initialise system trusted keyrings [ 0.197913] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.207642] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.208713] NFS: Registering the id_resolver key type [ 0.208767] Key type id_resolver registered [ 0.208782] Key type id_legacy registered [ 0.208862] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.209675] fuse: init (API version 7.31) [ 0.213974] Key type asymmetric registered [ 0.213995] Asymmetric key parser 'x509' registered [ 0.214112] bounce: pool size: 64 pages [ 0.214139] io scheduler mq-deadline registered [ 0.214155] io scheduler kyber registered [ 0.218668] imx6q-pcie 1ffc000.pcie: host bridge /soc/pcie@1ffc000 ranges: [ 0.218744] imx6q-pcie 1ffc000.pcie: IO 0x01f80000..0x01f8ffff -> 0x00000000 [ 0.218792] imx6q-pcie 1ffc000.pcie: MEM 0x01000000..0x01efffff -> 0x01000000 [ 0.222382] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 0.222592] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 0.225009] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 63, base_baud = 5000000) is a IMX [ 0.432757] imx6q-pcie 1ffc000.pcie: Link up [ 0.432772] imx6q-pcie 1ffc000.pcie: Link: Gen2 disabled [ 0.432788] imx6q-pcie 1ffc000.pcie: Link up, Gen1 [ 0.433089] imx6q-pcie 1ffc000.pcie: PCI host bridge to bus 0000:00 [ 0.433113] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.433132] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.433147] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff] [ 0.433208] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 0.433263] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 0.433295] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 0.433415] pci 0000:00:00.0: supports D1 [ 0.433432] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [ 0.443431] PCI: bus0: Fast back to back transfers disabled [ 0.452524] printk: console [ttymxc1] enabled [ 0.457506] pci 0000:01:00.0: [10b5:8605] type 01 class 0x060400 [ 0.464859] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 64, base_baud = 5000000) is a IMX [ 0.471144] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff] [ 1.045420] pci 0000:01:00.0: supports D1 D2 [ 1.049720] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.056633] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.059816] brd: module loaded [ 1.090896] loop: module loaded [ 1.095347] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 1 bytes/write [ 1.111966] PCI: bus1: Fast back to back transfers disabled [ 1.115041] da9062 2-0058: Device detected (device-ID: 0x62, var-ID: 0x22, DA9062) [ 1.117640] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.132102] buck1: mapping for mode 2 not defined [ 1.134384] pci 0000:02:01.0: [10b5:8605] type 01 class 0x060400 [ 1.141080] buck2: mapping for mode 2 not defined [ 1.145459] pci 0000:02:01.0: supports D1 D2 [ 1.150935] buck3: mapping for mode 2 not defined [ 1.153030] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.160781] buck4: mapping for mode 2 not defined [ 1.165605] pci 0000:02:02.0: [10b5:8605] type 01 class 0x060400 [ 1.173134] vdd_snvs: Bringing 3100000uV into 3000000-3000000uV [ 1.176628] pci 0000:02:02.0: supports D1 D2 [ 1.184894] vdd_high: Bringing 3100000uV into 3000000-3000000uV [ 1.185364] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.195081] vdd_eth_io: Bringing 2600000uV into 2500000-2500000uV [ 1.199096] pci 0000:02:03.0: [10b5:8605] type 01 class 0x060400 [ 1.206486] random: fast init done [ 1.211471] pci 0000:02:03.0: supports D1 D2 [ 1.213913] vdd_emmc: Bringing 1900000uV into 1800000-1800000uV [ 1.217737] pci 0000:02:03.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.229382] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 1.238426] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 1.239840] PCI: bus2: Fast back to back transfers disabled [ 1.246487] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 1.252084] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.260275] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 1.268376] pci 0000:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.279100] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 1.284078] pci 0000:02:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.291063] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.299888] pci 0000:03:00.0: [1912:0015] type 00 class 0x0c0330 [ 1.307868] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 1.323238] pci 0000:03:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 1.330943] pci 0000:03:00.0: PME# supported from D0 D3hot [ 1.333765] scsi host0: ahci-imx [ 1.336899] pci 0000:03:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.340548] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 67 [ 1.366074] libphy: Fixed MDIO Bus: probed [ 1.371078] CAN device driver interface [ 1.377871] usbcore: registered new interface driver asix [ 1.383406] usbcore: registered new interface driver ax88179_178a [ 1.389575] usbcore: registered new interface driver cdc_ether [ 1.391766] PCI: bus3: Fast back to back transfers disabled [ 1.395530] usbcore: registered new interface driver net1080 [ 1.401066] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03 [ 1.406829] usbcore: registered new interface driver cdc_subset [ 1.419402] usbcore: registered new interface driver zaurus [ 1.423154] PCI: bus4: Fast back to back transfers enabled [ 1.425124] usbcore: registered new interface driver cdc_ncm [ 1.430495] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 04 [ 1.436182] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.449351] ehci-pci: EHCI PCI platform driver [ 1.452591] PCI: bus5: Fast back to back transfers enabled [ 1.453918] ehci-platform: EHCI generic platform driver [ 1.459313] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05 [ 1.465055] ehci-mxc: Freescale On-Chip EHCI Host driver [ 1.471218] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05 [ 1.477127] usbcore: registered new interface driver usb-storage [ 1.483263] pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff] [ 1.496056] pci 0000:00:00.0: BAR 8: assigned [mem 0x01100000-0x013fffff] [ 1.502900] pci 0000:00:00.0: BAR 9: assigned [mem 0x01400000-0x015fffff pref] [ 1.510148] pci 0000:00:00.0: BAR 6: assigned [mem 0x01600000-0x0160ffff pref] [ 1.517427] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.523652] pci 0000:01:00.0: BAR 8: assigned [mem 0x01100000-0x012fffff] [ 1.530486] pci 0000:01:00.0: BAR 9: assigned [mem 0x01400000-0x015fffff 64bit pref] [ 1.538305] pci 0000:01:00.0: BAR 0: assigned [mem 0x01300000-0x01303fff] [ 1.544420] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.545184] pci 0000:01:00.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.550038] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 1.556158] pci 0000:02:01.0: BAR 8: assigned [mem 0x01100000-0x012fffff] [ 1.570027] pci 0000:02:01.0: BAR 9: assigned [mem 0x01400000-0x015fffff 64bit pref] [ 1.577822] pci 0000:02:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.584022] pci 0000:03:00.0: BAR 0: assigned [mem 0x01100000-0x01101fff 64bit] [ 1.591434] pci 0000:02:01.0: PCI bridge to [bus 03] [ 1.592307] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.596461] pci 0000:02:01.0: bridge window [io 0x1000-0x1fff] [ 1.603118] hub 1-0:1.0: USB hub found [ 1.607982] pci 0000:02:01.0: bridge window [mem 0x01100000-0x012fffff] [ 1.611734] hub 1-0:1.0: 1 port detected [ 1.618511] pci 0000:02:01.0: bridge window [mem 0x01400000-0x015fffff 64bit pref] [ 1.618577] pci 0000:02:02.0: PCI bridge to [bus 04] [ 1.627207] da9063-rtc da9062-rtc: DMA mask not set [ 1.630359] pci 0000:02:03.0: PCI bridge to [bus 05] [ 1.645199] pci 0000:01:00.0: PCI bridge to [bus 02-05] [ 1.645950] da9063-rtc da9062-rtc: registered as rtc1 [ 1.650454] pci 0000:01:00.0: bridge window [io 0x1000-0x1fff] [ 1.650505] pci 0000:01:00.0: bridge window [mem 0x01100000-0x012fffff] [ 1.657054] rtc-m41t80 0-0068: Can't clear HT bit [ 1.661696] pci 0000:01:00.0: bridge window [mem 0x01400000-0x015fffff 64bit pref] [ 1.670643] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc2 [ 1.673281] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.681326] i2c /dev entries driver [ 1.687148] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.698425] Bluetooth: HCI UART driver ver 2.3 [ 1.702000] pci 0000:00:00.0: bridge window [mem 0x01100000-0x013fffff] [ 1.706483] Bluetooth: HCI UART protocol H4 registered [ 1.713291] pci 0000:00:00.0: bridge window [mem 0x01400000-0x015fffff pref] [ 1.714014] pcieport 0000:00:00.0: PME: Signaling with IRQ 310 [ 1.719379] sdhci: Secure Digital Host Controller Interface driver [ 1.726380] pcieport 0000:00:00.0: AER: enabled with IRQ 310 [ 1.731570] sdhci: Copyright(c) Pierre Ossman [ 1.738430] pcieport 0000:01:00.0: enabling device (0140 -> 0143) [ 1.743497] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.745401] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO [ 1.750361] pcieport 0000:02:01.0: enabling device (0140 -> 0143) [ 1.778719] pci 0000:03:00.0: enabling device (0140 -> 0142) [ 1.805368] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA [ 1.862340] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.869326] ata1.00: ATA-10: ADATA SU800NS38, R0427AC, max UDMA/133 [ 1.875661] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 32) [ 1.882860] ata1.00: configured for UDMA/133 [ 2.002303] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.203882] hub 1-1:1.0: USB hub found [ 2.207885] hub 1-1:1.0: 4 ports detected [ 2.532298] usb 1-1.4: new high-speed USB device number 3 using ci_hdrc [ 2.706870] hub 1-1.4:1.0: USB hub found [ 2.711007] hub 1-1.4:1.0: 4 ports detected [ 8.263117] Unhandled fault: imprecise external abort (0x1406) at 0xfaf06a5b [ 8.270180] pgd = (ptrval) [ 8.272898] [faf06a5b] *pgd=00000000 [ 8.276495] Internal error: : 1406 [#1] SMP ARM [ 8.281035] Modules linked in: [ 8.284116] CPU: 2 PID: 7 Comm: kworker/u8:0 Not tainted 5.2.7-bsp-yocto-i.mx6-pd18.1.1 #1 [ 8.292390] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 8.298954] Workqueue: events_unbound async_run_entry_fn [ 8.304297] PC is at quirk_usb_early_handoff+0x400/0x7e0 [ 8.309634] LR is at __timer_delay+0x3c/0x88 [ 8.313916] pc : [<c05dd808>] lr : [<c085992c>] psr: 20000013 [ 8.320194] sp : e4085d60 ip : 00000000 fp : 0020c498 [ 8.325430] r10: c0b388d4 r9 : 00000000 r8 : f097c024 [ 8.330666] r7 : 000091d1 r6 : f097c000 r5 : c0d05148 r4 : e444a000 [ 8.337205] r3 : 00000000 r2 : fffe5480 r1 : 00000730 r0 : 0000001d [ 8.343747] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 8.350894] Control: 10c5387d Table: 1000404a DAC: 00000051 [ 8.356652] Process kworker/u8:0 (pid: 7, stack limit = 0x(ptrval)) [ 8.362932] Stack: (0xe4085d60 to 0xe4086000) [ 8.367313] 5d60: f097c020 00000504 e42323b8 c041d570 3b9aca00 5a6c0a29 e4085d9c c0b4a25c [ 8.375510] 5d80: e444a000 c0b4a26c 0000ffff c0d5b820 c05dd408 00000000 69e28c0a c0466a5c [ 8.383706] 5da0: 00000000 c04ec3c4 e4449878 e4084000 c0d05148 e444a000 e4479814 e4479800 [ 8.391901] 5dc0: e423d618 e40e5210 e423d618 e423d440 e6f9e968 c0450b9c e444a000 e4479814 [ 8.400097] 5de0: e4479800 c0450c44 e4448800 e4478814 e4478800 c0450c78 e4065000 e423f414 [ 8.408294] 5e00: e423f400 c0450c78 e4064800 e423ec14 e423ec00 c0450c78 e43cc858 e423ec0c [ 8.416490] 5e20: 00000000 c0475254 00000000 00000000 00000000 e43cc840 e40e5210 e6f9e968 [ 8.424685] 5e40: e40e5200 e43cc840 c0d05148 00000000 00000000 c0476bd4 00000000 00000001 [ 8.432880] 5e60: 00000000 c02a57b0 00000000 00000000 00000000 00000000 00000000 00000000 [ 8.441074] 5e80: 00000000 5a6c0a29 00000000 e40e5210 00000000 c0d2022c 00000000 00000000 [ 8.449269] 5ea0: c0d2022c 00000000 ffffe000 c04e3538 e40e5210 c0db5b34 c0db5b38 00000000 [ 8.457464] 5ec0: 00000000 c04e17c4 e40e5210 c0d2022c e42b0c80 e4008000 00000000 00000000 [ 8.465659] 5ee0: e42b0c94 c04e1afc 00000000 c0d179f8 00000000 e40e5210 c0d5b820 e42b0c80 [ 8.473855] 5f00: e4008000 00000000 00000000 c04e1c50 e42b0c90 c0144ca0 e42b0c90 e401b580 [ 8.482051] 5f20: e4006200 e4008000 00000000 c013bae4 00000088 e4006218 e401b580 e401b594 [ 8.490246] 5f40: e4006200 00000088 e4006218 c0d03d00 e4006200 c013c8ec e406a280 00000000 [ 8.498441] 5f60: ffffe000 00000000 e4030b80 e4030a40 e4084000 e401b580 c013c8c0 e4055ea4 [ 8.506636] 5f80: e4030b9c c0141b18 e4072480 e4030a40 c01419e8 00000000 00000000 00000000 [ 8.514830] 5fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000 [ 8.523023] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 8.531216] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 8.539442] [<c05dd808>] (quirk_usb_early_handoff) from [<c0466a5c>] (pci_do_fixups+0xd8/0x144) [ 8.548179] [<c0466a5c>] (pci_do_fixups) from [<c0450b9c>] (pci_bus_add_device+0x18/0x94) [ 8.556383] [<c0450b9c>] (pci_bus_add_device) from [<c0450c44>] (pci_bus_add_devices+0x2c/0x70) [ 8.565103] [<c0450c44>] (pci_bus_add_devices) from [<c0450c78>] (pci_bus_add_devices+0x60/0x70) [ 8.573908] Code: e2577001 0a0000b5 e5983000 ee079f9a (e3130b02) [ 8.580028] ---[ end trace d9b763ceb334a93b ]--- [ 8.616873] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 8.625016] leds-pca953x 0-0062: setting platform data [ 8.632724] gpio gpiochip7: GPIO integer space overlap, cannot add chip [ 8.639385] gpiochip_add_data_with_key: GPIOs 0..3 (gpio-pca9532) failed to register, -16 [ 8.647652] leds-pca953x 0-0062: could not add gpiochip [ 8.661886] caam 2100000.caam: Entropy delay = 3200 [ 8.727627] caam 2100000.caam: Instantiated RNG4 SH0 [ 8.788388] caam 2100000.caam: Instantiated RNG4 SH1 [ 8.793408] caam 2100000.caam: device ID = 0x0a16010000000000 (Era 4) [ 8.799880] caam 2100000.caam: job rings = 2, qi = 0 [ 8.832613] caam algorithms registered in /proc/crypto [ 8.847675] caam_jr 2101000.jr0: registering rng-caam [ 8.850017] mmc1: new DDR MMC card at address 0001 [ 8.853722] hidraw: raw HID events driver (C) Jiri Kosina [ 8.860165] mmcblk1: mmc1:0001 Q2J55L 7.09 GiB [ 8.863418] usbcore: registered new interface driver usbhid [ 8.869589] mmcblk1boot0: mmc1:0001 Q2J55L partition 1 16.0 MiB [ 8.873257] usbhid: USB HID core driver [ 8.881187] mmcblk1boot1: mmc1:0001 Q2J55L partition 2 16.0 MiB [ 8.887424] NET: Registered protocol family 10 [ 8.889380] mmcblk1rpmb: mmc1:0001 Q2J55L partition 3 4.00 MiB, chardev (247:0) [ 8.895030] Segment Routing with IPv6 [ 8.903032] mmcblk1: p1 p2 [ 8.904682] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 8.914409] NET: Registered protocol family 17 [ 8.918894] can: controller area network core (rev 20170425 abi 9) [ 8.925265] NET: Registered protocol family 29 [ 8.929747] can: raw protocol (rev 20170425) [ 8.934076] can: broadcast manager protocol (rev 20170425 t) [ 8.939777] can: netlink gateway (rev 20170425) max_hops=1 [ 8.945587] 8021q: 802.1Q VLAN Support v1.8 [ 8.949853] Key type dns_resolver registered [ 8.954839] vddarm: supplied by vdd_arm [ 8.959844] vddpu: supplied by vdd_soc [ 8.964669] vddsoc: supplied by vdd_soc [ 8.971151] Registering SWP/SWPB emulation handler [ 8.976724] Loading compiled-in X.509 certificates [ 8.997905] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 9.002301] usb 1-1.4.1: new full-speed USB device number 4 using ci_hdrc [ 9.016846] hctosys: unable to open rtc device (rtc0) [ 9.022666] VCC_CAM0: disabling [ 9.025820] flexcan1-reg: disabling [ 9.029318] usb_otg_vbus: disabling [ 9.032867] peb-display: disabling [ 9.036999] vdd_eth_io: disabling -- Fawad Lateef On Thu, 22 Aug 2019 at 11:34, Schmid, Carsten <Carsten_Schmid@xxxxxxxxxx> wrote: > > > > > Have a question that: Can I disable PCIe power management completely > > using some kernel CONFIG option OR boot parameter? If yes then how? > > > > Thanks > > > See CONFIG_PM and what it depends on. > > BR > Carsten
