The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: Craig Shelley <craig@xxxxxxxxxxxxxxxx>
---
drivers/usb/serial/cp210x.c | 98 ++++++++++++++++++++++++------------------
1 files changed, 56 insertions(+), 42 deletions(-)
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index 47c96f0..5c18a62 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -27,7 +27,7 @@
/*
* Version Information
*/
-#define DRIVER_VERSION "v0.08"
+#define DRIVER_VERSION "v0.09"
#define DRIVER_DESC "Silicon Labs CP2101/CP2102 RS232 serial adaptor driver"
/*
@@ -145,23 +145,40 @@ static struct usb_serial_driver cp2101_device = {
#define REQTYPE_HOST_TO_DEVICE 0x41
#define REQTYPE_DEVICE_TO_HOST 0xc1
-/* Config SET requests. To GET, add 1 to the request number */
-#define CP2101_UART 0x00 /* Enable / Disable */
-#define CP2101_BAUDRATE 0x01 /* (BAUD_RATE_GEN_FREQ / baudrate) */
-#define CP2101_BITS 0x03 /* 0x(0)(databits)(parity)(stopbits) */
-#define CP2101_BREAK 0x05 /* On / Off */
-#define CP2101_CONTROL 0x07 /* Flow control line states */
-#define CP2101_MODEMCTL 0x13 /* Modem controls */
-#define CP2101_CONFIG_6 0x19 /* 6 bytes of config data ??? */
-
-/* CP2101_UART */
+/* Config request codes */
+#define CP210X_IFC_ENABLE 0x00
+#define CP210X_SET_BAUDDIV 0x01
+#define CP210X_GET_BAUDDIV 0x02
+#define CP210X_SET_LINE_CTL 0x03
+#define CP210X_GET_LINE_CTL 0x04
+#define CP210X_SET_BREAK 0x05
+#define CP210X_IMM_CHAR 0x06
+#define CP210X_SET_MHS 0x07
+#define CP210X_GET_MDMSTS 0x08
+#define CP210X_SET_XON 0x09
+#define CP210X_SET_XOFF 0x0A
+#define CP210X_SET_EVENTMASK 0x0B
+#define CP210X_GET_EVENTMASK 0x0C
+#define CP210X_SET_CHAR 0x0D
+#define CP210X_GET_CHARS 0x0E
+#define CP210X_GET_PROPS 0x0F
+#define CP210X_GET_COMM_STATUS 0x10
+#define CP210X_RESET 0x11
+#define CP210X_PURGE 0x12
+#define CP210X_SET_FLOW 0x13
+#define CP210X_GET_FLOW 0x14
+#define CP210X_EMBED_EVENTS 0x15
+#define CP210X_GET_EVENTSTATE 0x16
+#define CP210X_SET_CHARS 0x19
+
+/* CP210X_IFC_ENABLE */
#define UART_ENABLE 0x0001
#define UART_DISABLE 0x0000
-/* CP2101_BAUDRATE */
+/* CP210X_(SET|GET)_BAUDDIV */
#define BAUD_RATE_GEN_FREQ 0x384000
-/* CP2101_BITS */
+/* CP210X_(SET|GET)_LINE_CTL */
#define BITS_DATA_MASK 0X0f00
#define BITS_DATA_5 0X0500
#define BITS_DATA_6 0X0600
@@ -181,11 +198,11 @@ static struct usb_serial_driver cp2101_device = {
#define BITS_STOP_1_5 0x0001
#define BITS_STOP_2 0x0002
-/* CP2101_BREAK */
+/* CP210X_SET_BREAK */
#define BREAK_ON 0x0000
#define BREAK_OFF 0x0001
-/* CP2101_CONTROL */
+/* CP210X_(SET_MHS|GET_MDMSTS) */
#define CONTROL_DTR 0x0001
#define CONTROL_RTS 0x0002
#define CONTROL_CTS 0x0010
@@ -218,9 +235,6 @@ static int cp2101_get_config(struct usb_serial_port *port, u8 request,
return -ENOMEM;
}
- /* For get requests, the request number must be incremented */
- request++;
-
/* Issue the request, attempting to read 'size' bytes */
result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
request, REQTYPE_DEVICE_TO_HOST, 0x0000,
@@ -358,7 +372,7 @@ static int cp2101_open(struct tty_struct *tty, struct usb_serial_port *port,
dbg("%s - port %d", __func__, port->number);
- if (cp2101_set_config_single(port, CP2101_UART, UART_ENABLE)) {
+ if (cp2101_set_config_single(port, CP210X_IFC_ENABLE, UART_ENABLE)) {
dev_err(&port->dev, "%s - Unable to enable UART\n",
__func__);
return -EPROTO;
@@ -417,7 +431,7 @@ static void cp2101_close(struct tty_struct *tty, struct usb_serial_port *port,
mutex_lock(&port->serial->disc_mutex);
if (!port->serial->disconnected)
- cp2101_set_config_single(port, CP2101_UART, UART_DISABLE);
+ cp2101_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
mutex_unlock(&port->serial->disc_mutex);
}
@@ -458,7 +472,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
dbg("%s - port %d", __func__, port->number);
- cp2101_get_config(port, CP2101_BAUDRATE, &baud, 2);
+ cp2101_get_config(port, CP210X_GET_BAUDDIV, &baud, 2);
/* Convert to baudrate */
if (baud)
baud = cp2101_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
@@ -468,7 +482,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
cflag = *cflagp;
- cp2101_get_config(port, CP2101_BITS, &bits, 2);
+ cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
cflag &= ~CSIZE;
switch (bits & BITS_DATA_MASK) {
case BITS_DATA_5:
@@ -493,14 +507,14 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
cflag |= CS8;
bits &= ~BITS_DATA_MASK;
bits |= BITS_DATA_8;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
default:
dbg("%s - Unknown number of data bits, using 8", __func__);
cflag |= CS8;
bits &= ~BITS_DATA_MASK;
bits |= BITS_DATA_8;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
@@ -523,20 +537,20 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
__func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
case BITS_PARITY_SPACE:
dbg("%s - parity = SPACE (not supported, disabling parity)",
__func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
default:
dbg("%s - Unknown parity mode, disabling parity", __func__);
cflag &= ~PARENB;
bits &= ~BITS_PARITY_MASK;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
@@ -549,7 +563,7 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
dbg("%s - stop bits = 1.5 (not supported, using 1 stop bit)",
__func__);
bits &= ~BITS_STOP_MASK;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
case BITS_STOP_2:
dbg("%s - stop bits = 2", __func__);
@@ -559,11 +573,11 @@ static void cp2101_get_termios_port(struct usb_serial_port *port,
dbg("%s - Unknown number of stop bits, using 1 stop bit",
__func__);
bits &= ~BITS_STOP_MASK;
- cp2101_set_config(port, CP2101_BITS, &bits, 2);
+ cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
break;
}
- cp2101_get_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+ cp2101_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
if (modem_ctl[0] & 0x0008) {
dbg("%s - flow control = CRTSCTS", __func__);
cflag |= CRTSCTS;
@@ -596,7 +610,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
dbg("%s - Setting baud rate to %d baud", __func__,
baud);
- if (cp2101_set_config_single(port, CP2101_BAUDRATE,
+ if (cp2101_set_config_single(port, CP210X_SET_BAUDDIV,
((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
dbg("Baud rate requested not supported by device\n");
baud = tty_termios_baud_rate(old_termios);
@@ -607,7 +621,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
/* If the number of data bits is to be updated */
if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
- cp2101_get_config(port, CP2101_BITS, &bits, 2);
+ cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_DATA_MASK;
switch (cflag & CSIZE) {
case CS5:
@@ -637,13 +651,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
bits |= BITS_DATA_8;
break;
}
- if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+ if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Number of data bits requested "
"not supported by device\n");
}
if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))) {
- cp2101_get_config(port, CP2101_BITS, &bits, 2);
+ cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_PARITY_MASK;
if (cflag & PARENB) {
if (cflag & PARODD) {
@@ -654,13 +668,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
dbg("%s - parity = EVEN", __func__);
}
}
- if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+ if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Parity mode not supported "
"by device\n");
}
if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
- cp2101_get_config(port, CP2101_BITS, &bits, 2);
+ cp2101_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
bits &= ~BITS_STOP_MASK;
if (cflag & CSTOPB) {
bits |= BITS_STOP_2;
@@ -669,13 +683,13 @@ static void cp2101_set_termios(struct tty_struct *tty,
bits |= BITS_STOP_1;
dbg("%s - stop bits = 1", __func__);
}
- if (cp2101_set_config(port, CP2101_BITS, &bits, 2))
+ if (cp2101_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
dbg("Number of stop bits requested "
"not supported by device\n");
}
if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
- cp2101_get_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+ cp2101_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
dbg("%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
__func__, modem_ctl[0], modem_ctl[1],
modem_ctl[2], modem_ctl[3]);
@@ -695,7 +709,7 @@ static void cp2101_set_termios(struct tty_struct *tty,
dbg("%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
__func__, modem_ctl[0], modem_ctl[1],
modem_ctl[2], modem_ctl[3]);
- cp2101_set_config(port, CP2101_MODEMCTL, modem_ctl, 16);
+ cp2101_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
}
}
@@ -733,7 +747,7 @@ static int cp2101_tiocmset_port(struct usb_serial_port *port, struct file *file,
dbg("%s - control = 0x%.4x", __func__, control);
- return cp2101_set_config(port, CP2101_CONTROL, &control, 2);
+ return cp2101_set_config(port, CP210X_SET_MHS, &control, 2);
}
static int cp2101_tiocmget (struct tty_struct *tty, struct file *file)
@@ -744,7 +758,7 @@ static int cp2101_tiocmget (struct tty_struct *tty, struct file *file)
dbg("%s - port %d", __func__, port->number);
- cp2101_get_config(port, CP2101_CONTROL, &control, 1);
+ cp2101_get_config(port, CP210X_GET_MDMSTS, &control, 1);
result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
|((control & CONTROL_RTS) ? TIOCM_RTS : 0)
@@ -770,7 +784,7 @@ static void cp2101_break_ctl (struct tty_struct *tty, int break_state)
state = BREAK_ON;
dbg("%s - turning break %s", __func__,
state == BREAK_OFF ? "off" : "on");
- cp2101_set_config(port, CP2101_BREAK, &state, 2);
+ cp2101_set_config(port, CP210X_SET_BREAK, &state, 2);
}
static int cp2101_startup(struct usb_serial *serial)
--
1.5.6.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
