Oops in xhci_endpoint_reset

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,


I have seen kernel oopses on waking from suspend to memory. I got this
twice, one dmesg with backtrace attached. The other one had the failure
in the same place in the code.


This is kernel 5.3.0-rc1, patched for another problem in ethernet PHY
driver. Have not had the problem with earlier kernels. Using Gentoo
linux, amd64, but git kernel.


Best Wishes,


Bob Gleitsmann

Oops#1 Part14
<6>[    1.091483]  sda: sda1 sda2 sda3
<5>[    1.091976] sd 2:0:0:0: [sdb] 4096-byte physical blocks
<5>[    1.093079] sd 1:0:0:0: [sda] Attached SCSI disk
<5>[    1.093356] sd 2:0:0:0: [sdb] Write Protect is off
<7>[    1.094495] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
<5>[    1.094514] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
<6>[    1.139099]  sdb: sdb1 sdb2 sdb3 sdb4
<5>[    1.140084] sd 2:0:0:0: [sdb] Attached SCSI disk
<7>[    1.167738] PM: Image not found (code -22)
<6>[    1.207334] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
<6>[    1.207966] VFS: Mounted root (ext4 filesystem) readonly on device 8:19.
<6>[    1.210562] Freeing unused kernel image memory: 2292K
<6>[    1.211188] Write protecting the kernel read-only data: 18432k
<6>[    1.212437] Freeing unused kernel image memory: 2028K
<6>[    1.213310] Freeing unused kernel image memory: 840K
<6>[    1.213904] rodata_test: all tests were successful
<6>[    1.214516] Run /sbin/init as init process
<6>[    1.239825] usb 7-1: New USB device found, idVendor=0763, idProduct=1011, bcdDevice= 1.21
<6>[    1.240419] usb 7-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>[    1.412871] tsc: Refined TSC clocksource calibration: 4219.303 MHz
<6>[    1.413658] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x3cd19c0c3f5, max_idle_ns: 440795202126 ns
<6>[    1.414342] clocksource: Switched to clocksource tsc
<5>[    1.561167] audit: type=1404 audit(1564013745.305:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 enabled=1 old-enabled=1 lsm=selinux res=1
<5>[    1.604674] random: fast init done
<6>[    1.627185] SELinux:  policy capability network_peer_controls=0
<6>[    1.627868] SELinux:  policy capability open_perms=1
Oops#1 Part13
<6>[    1.628536] SELinux:  policy capability extended_socket_class=1
<6>[    1.629171] SELinux:  policy capability always_check_network=0
<6>[    1.629828] SELinux:  policy capability cgroup_seclabel=1
<6>[    1.630440] SELinux:  policy capability nnp_nosuid_transition=1
<6>[    1.638864] usb 3-3: new high-speed USB device number 3 using ehci-pci
<5>[    1.643997] audit: type=1403 audit(1564013745.388:3): auid=4294967295 ses=4294967295 lsm=selinux res=1
<6>[    1.769120] usb 3-3: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00
<6>[    1.769794] usb 3-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>[    1.771240] hub 3-3:1.0: USB hub found
<6>[    1.772422] hub 3-3:1.0: 4 ports detected
<6>[    2.017868] usb 7-4: new low-speed USB device number 3 using ohci-pci
<5>[    2.075368] random: crng init done
<6>[    2.181898] usb 7-4: New USB device found, idVendor=05b8, idProduct=3279, bcdDevice= 0.01
<6>[    2.182697] usb 7-4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
<6>[    2.183347] usb 7-4: Product: Wired Keyboard
<6>[    2.190294] input: Wired Keyboard as /devices/pci0000:00/0000:00:16.0/usb7/7-4/7-4:1.0/0003:05B8:3279.0001/input/input2
<6>[    2.243248] hid-generic 0003:05B8:3279.0001: input,hidraw0: USB HID v1.11 Keyboard [Wired Keyboard] on usb-0000:00:16.0-4/input0
<6>[    2.249162] input: Wired Keyboard Consumer Control as /devices/pci0000:00/0000:00:16.0/usb7/7-4/7-4:1.1/0003:05B8:3279.0002/input/input3
<6>[    2.302089] input: Wired Keyboard System Control as /devices/pci0000:00/0000:00:16.0/usb7/7-4/7-4:1.1/0003:05B8:3279.0002/input/input4
<6>[    2.303797] hid-generic 0003:05B8:3279.0002: input,hidraw1: USB HID v1.11 Device [Wired Keyboard] on usb-0000:00:16.0-4/input1
Oops#1 Part12
<6>[    2.601802] usb 3-3.1: new full-speed USB device number 5 using ehci-pci
<6>[    2.697733] usb 3-3.1: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.01
<6>[    2.698509] usb 3-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>[    2.699309] usb 3-3.1: Product: USB Receiver
<6>[    2.700092] usb 3-3.1: Manufacturer: Logitech
<6>[    2.702849] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.0/0003:046D:C52B.0003/input/input5
<6>[    2.756138] hid-generic 0003:046D:C52B.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:16.2-3.1/input0
<6>[    2.760142] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.1/0003:046D:C52B.0004/input/input6
<6>[    2.761859] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.1/0003:046D:C52B.0004/input/input7
<6>[    2.815022] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.1/0003:046D:C52B.0004/input/input8
<6>[    2.817123] hid-generic 0003:046D:C52B.0004: input,hiddev96,hidraw3: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:16.2-3.1/input1
<6>[    2.820802] hid-generic 0003:046D:C52B.0005: hiddev97,hidraw4: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:16.2-3.1/input2
<30>[    6.628763] udevd[652]: starting version 3.2.5
<4>[    7.100252] Failed to create system directory mdio
<5>[    7.100261] audit: type=1400 audit(1564013750.844:4): avc:  denied  { search } for  pid=742 comm="modprobe" name="events" dev="tracefs" ino=34 scontext=system_u:system_r:kmod_t tcontext=system_u:object_r:tracefs_t tclass=dir permissive=0
Oops#1 Part11
<4>[    7.214206] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
<6>[    7.217716] libphy: r8169: probed
<6>[    7.217879] r8169 0000:03:00.0 eth0: RTL8168g/8111g, fc:aa:14:c9:ba:a5, XID 4c0, IRQ 32
<6>[    7.217881] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
<6>[    7.330618] cryptd: max_cpu_qlen set to 1000
<6>[    7.670358] fuse: init (API version 7.31)
<30>[    7.714861] udevd[652]: starting eudev-3.2.5
<6>[    7.776379] it87: Found IT8620E chip at 0x228, revision 4
<6>[    7.776401] it87: Beeping is supported
<6>[    7.819883] acpi_cpufreq: overriding BIOS provided _PSD data
<6>[    7.884959] scsi host4: pata_atiixp
<6>[    7.885050] scsi host5: pata_atiixp
<6>[    7.885080] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
<6>[    7.885080] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
<6>[    7.931619] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
<6>[    7.931624] piix4_smbus 0000:00:14.0: Using register 0x2c for SMBus port selection
<6>[    7.931694] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
<6>[    8.025830] Emu10k1_gameport 0000:04:06.1: enabling device (0000 -> 0001)
<6>[    8.041464] gameport gameport0: EMU10K1 is pci0000:04:06.1/gameport0, io 0xc040, speed 793kHz
<6>[    8.064877] firewire_ohci 0000:04:06.2: enabling device (0000 -> 0002)
<5>[    8.117819] firewire_ohci 0000:04:06.2: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x2
<6>[    8.288074] EFI Variables Facility v0.08 2004-May-17
Oops#1 Part10
<6>[    8.301205] xhci_hcd 0000:02:00.0: xHCI Host Controller
<6>[    8.301325] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8
<6>[    8.301394] xhci_hcd 0000:02:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000000000000090
<6>[    8.301554] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
<6>[    8.301556] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[    8.301557] usb usb8: Product: xHCI Host Controller
<6>[    8.301558] usb usb8: Manufacturer: Linux 5.3.0-rc1+ xhci-hcd
<6>[    8.301559] usb usb8: SerialNumber: 0000:02:00.0
<6>[    8.301649] hub 8-0:1.0: USB hub found
<6>[    8.301655] hub 8-0:1.0: 1 port detected
<6>[    8.301739] xhci_hcd 0000:02:00.0: xHCI Host Controller
<6>[    8.301780] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9
<6>[    8.301783] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed
<6>[    8.301802] usb usb9: We don't know the algorithms for LPM for this host, disabling LPM.
<6>[    8.301826] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
<6>[    8.301827] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[    8.301828] usb usb9: Product: xHCI Host Controller
<6>[    8.301829] usb usb9: Manufacturer: Linux 5.3.0-rc1+ xhci-hcd
<6>[    8.301830] usb usb9: SerialNumber: 0000:02:00.0
<6>[    8.301912] hub 9-0:1.0: USB hub found
<6>[    8.301919] hub 9-0:1.0: 4 ports detected
<6>[    8.429878] pstore: Using crash dump compression: deflate
<6>[    8.429890] pstore: Registered efi as persistent store backend
<6>[    8.441893] logitech-djreceiver 0003:046D:C52B.0005: hiddev96,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:16.2-3.1/input2
Oops#1 Part9
<6>[    8.518732] input: PC Speaker as /devices/platform/pcspkr/input/input10
<6>[    8.549045] input: Logitech Unifying Device. Wireless PID:1025 Mouse as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.2/0003:046D:C52B.0005/0003:046D:1025.0006/input/input11
<6>[    8.549179] hid-generic 0003:046D:1025.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1025] on usb-0000:00:16.2-3.1/input2:1
<6>[    8.610683] usbcore: registered new interface driver snd-usb-audio
<6>[    8.612598] AVX version of gcm_enc/dec engaged.
<6>[    8.612599] AES CTR mode by8 optimization enabled
<5>[    8.620860] firewire_core 0000:04:06.2: created device fw0: GUID 00023c015113a989, S400
<6>[    8.622787] usb 8-1: new high-speed USB device number 2 using xhci_hcd
<6>[    8.688596] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC892: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
<6>[    8.688599] snd_hda_codec_realtek hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6>[    8.688602] snd_hda_codec_realtek hdaudioC1D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
<6>[    8.688603] snd_hda_codec_realtek hdaudioC1D0:    mono: mono_out=0x0
<6>[    8.688605] snd_hda_codec_realtek hdaudioC1D0:    dig-out=0x11/0x1e
<6>[    8.688607] snd_hda_codec_realtek hdaudioC1D0:    inputs:
<6>[    8.688609] snd_hda_codec_realtek hdaudioC1D0:      Front Mic=0x19
<6>[    8.688611] snd_hda_codec_realtek hdaudioC1D0:      Rear Mic=0x18
<6>[    8.688612] snd_hda_codec_realtek hdaudioC1D0:      Line=0x1a
<6>[    8.688801] snd_emu10k1 0000:04:06.0: enabling device (0000 -> 0001)
<6>[    8.694273] snd_emu10k1 0000:04:06.0: Installing spdif_bug patch: SB Audigy 2 ZS [SB0350]
<6>[    8.709178] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input15
Oops#1 Part8
<6>[    8.709377] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input16
<6>[    8.709539] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input17
<6>[    8.709597] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card1/input18
<6>[    8.709659] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card1/input19
<6>[    8.709723] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card1/input20
<6>[    8.709766] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card1/input21
<6>[    8.709818] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input22
<6>[    8.750916] usb 8-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20
<6>[    8.750919] usb 8-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
<6>[    8.750920] usb 8-1: Product: USB2.0 Hub
<6>[    8.751587] hub 8-1:1.0: USB hub found
<6>[    8.751945] hub 8-1:1.0: 4 ports detected
<6>[    8.757505] r8169 0000:03:00.0 enp3s0: renamed from eth0
<6>[    8.799012] input: Logitech M510 as /devices/pci0000:00/0000:00:16.2/usb3/3-3/3-3.1/3-3.1:1.2/0003:046D:C52B.0005/0003:046D:1025.0006/input/input23
<6>[    8.799178] logitech-hidpp-device 0003:046D:1025.0006: input,hidraw3: USB HID v1.11 Mouse [Logitech M510] on usb-0000:00:16.2-3.1/input2:1
<6>[    9.028869] usb 8-1.1: new full-speed USB device number 3 using xhci_hcd
<6>[    9.113622] usb 8-1.1: New USB device found, idVendor=051d, idProduct=0002, bcdDevice= 0.90
<6>[    9.113626] usb 8-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[    9.113628] usb 8-1.1: Product: Back-UPS XS 1300G FW:864.L8 .D USB FW:L8 
Oops#1 Part7
<6>[    9.113630] usb 8-1.1: Manufacturer: American Power Conversion
<6>[    9.113632] usb 8-1.1: SerialNumber: 4B1519P43922  
<6>[    9.129850] hid-generic 0003:051D:0002.0007: hiddev97,hidraw4: USB HID v1.00 Device [American Power Conversion Back-UPS XS 1300G FW:864.L8 .D USB FW:L8 ] on usb-0000:02:00.0-1.1/input0
<6>[    9.193889] usb 8-1.2: new full-speed USB device number 4 using xhci_hcd
<6>[    9.525423] usb 8-1.2: New USB device found, idVendor=03f0, idProduct=1004, bcdDevice= 1.00
<6>[    9.525428] usb 8-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[    9.525430] usb 8-1.2: Product: DeskJet 970C
<6>[    9.525433] usb 8-1.2: Manufacturer: Hewlett-Packard
<6>[    9.525436] usb 8-1.2: SerialNumber: xxxxx
<6>[    9.593321] kvm: Nested Virtualization enabled
<6>[    9.593326] kvm: Nested Paging enabled
<6>[    9.635605] MCE: In-kernel MCE decoding enabled.
<6>[    9.668335] usblp 8-1.2:1.0: usblp0: USB Bidirectional printer dev 4 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1004
<6>[    9.668403] usbcore: registered new interface driver usblp
<6>[    9.703745] EDAC amd64: Node 0: DRAM ECC disabled.
<6>[    9.703746] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
<6>[    9.703746]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
<6>[    9.703746]  (Note that use of the override may cause unknown side effects.)
<6>[    9.717245] EDAC amd64: Node 0: DRAM ECC disabled.
<6>[    9.717246] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
<6>[    9.717246]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
<6>[    9.717246]  (Note that use of the override may cause unknown side effects.)
Oops#1 Part6
<6>[    9.733583] EDAC amd64: Node 0: DRAM ECC disabled.
<6>[    9.733586] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
<6>[    9.733586]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
<6>[    9.733586]  (Note that use of the override may cause unknown side effects.)
<6>[    9.748661] EDAC amd64: Node 0: DRAM ECC disabled.
<6>[    9.748664] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
<6>[    9.748664]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
<6>[    9.748664]  (Note that use of the override may cause unknown side effects.)
<6>[   12.280195] EXT4-fs (sdb3): re-mounted. Opts: (null)
<6>[   12.880856] Adding 19433468k swap on /dev/sdb4.  Priority:-2 extents:1 across:19433468k FS
<7>[   16.821920] checking generic (f5000000 300000) vs hw (c0000000 10000000)
<7>[   16.821922] checking generic (f5000000 300000) vs hw (f4000000 2000000)
<6>[   16.821923] fb0: switching to nouveaufb from simple
<6>[   16.822023] Console: switching to colour dummy device 80x25
<6>[   16.822128] nouveau 0000:01:00.0: NVIDIA G92 (092a00a2)
<6>[   16.937255] nouveau 0000:01:00.0: bios: version 62.92.ad.00.00
<6>[   16.957682] nouveau 0000:01:00.0: fb: 1024 MiB GDDR3
<6>[   17.116860] [TTM] Zone  kernel: Available graphics memory: 4026756 KiB
<6>[   17.116861] [TTM] Zone   dma32: Available graphics memory: 2097152 KiB
<6>[   17.116862] [TTM] Initializing pool allocator
<6>[   17.116866] [TTM] Initializing DMA pool allocator
<6>[   17.116877] nouveau 0000:01:00.0: DRM: VRAM: 1024 MiB
<6>[   17.116878] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB
Oops#1 Part5
<6>[   17.116881] nouveau 0000:01:00.0: DRM: TMDS table version 2.0
<6>[   17.116882] nouveau 0000:01:00.0: DRM: DCB version 4.0
<6>[   17.116883] nouveau 0000:01:00.0: DRM: DCB outp 00: 02000300 00000028
<6>[   17.116885] nouveau 0000:01:00.0: DRM: DCB outp 01: 01000302 00020030
<6>[   17.116886] nouveau 0000:01:00.0: DRM: DCB outp 02: 04011310 00000028
<6>[   17.116887] nouveau 0000:01:00.0: DRM: DCB outp 03: 02011312 00020030
<6>[   17.116888] nouveau 0000:01:00.0: DRM: DCB conn 00: 00001030
<6>[   17.116889] nouveau 0000:01:00.0: DRM: DCB conn 01: 00002130
<6>[   17.118677] nouveau 0000:01:00.0: DRM: MM: using CRYPT for buffer copies
<6>[   17.119113] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
<6>[   17.119114] [drm] Driver supports precise vblank timestamp query.
<6>[   17.159424] nouveau 0000:01:00.0: DRM: allocated 1920x1080 fb: 0x70000, bo 000000001c943f0c
<6>[   17.187563] fbcon: nouveaudrmfb (fb0) is primary device
<6>[   17.245738] Console: switching to colour frame buffer device 240x67
<6>[   17.247686] nouveau 0000:01:00.0: fb0: nouveaudrmfb frame buffer device
<6>[   17.256326] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0
<38>[   17.919469] elogind-daemon[1465]: New seat seat0.
<38>[   17.920283] elogind-daemon[1465]: Watching system buttons on /dev/input/event1 (Power Button)
<38>[   17.920346] elogind-daemon[1465]: Watching system buttons on /dev/input/event0 (Power Button)
<38>[   17.920440] elogind-daemon[1465]: Watching system buttons on /dev/input/event2 (Wired Keyboard)
<38>[   17.920532] elogind-daemon[1465]: Watching system buttons on /dev/input/event3 (Wired Keyboard Consumer Control)
<38>[   17.920622] elogind-daemon[1465]: Watching system buttons on /dev/input/event4 (Wired Keyboard System Control)
Oops#1 Part4
<6>[   19.712581] Generic Realtek PHY r8169-300:00: attached PHY driver [Generic Realtek PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
<6>[   19.812678] r8169 0000:03:00.0 enp3s0: Link is Down
<6>[   21.486763] r8169 0000:03:00.0 enp3s0: Link is Up - 100Mbps/Full - flow control rx/tx
<6>[   21.486800] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
<38>[   27.078754] elogind-daemon[1465]: New session c1 of user sddm.
<38>[   37.171593] elogind-daemon[1465]: New session 1 of user xx.
<38>[   38.279554] elogind-daemon[1465]: Removed session c1.
<6>[   93.931664] logitech-hidpp-device 0003:046D:1025.0006: HID++ 1.0 device connected.
<6>[  231.948951] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
<6>[  232.166282] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
<6>[ 1118.875810] traps: plugin-containe[3573] general protection fault ip:7f482d094339 sp:7ffca48d7470 error:0 in ld-2.29.so[7f482d081000+1e000]
<38>[ 2990.080236] elogind-daemon[1465]: Suspending system...
<6>[ 2990.080247] PM: suspend entry (deep)
<6>[ 2990.174030] Filesystems sync: 0.093 seconds
<6>[ 2990.174196] Freezing user space processes ... (elapsed 0.001 seconds) done.
<6>[ 2990.175677] OOM killer disabled.
<6>[ 2990.175678] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
<6>[ 2990.176928] printk: Suspending console(s) (use no_console_suspend to debug)
<6>[ 2990.177558] r8169 0000:03:00.0 enp3s0: Link is Down
<6>[ 2990.177833] serial 00:03: disabled
<5>[ 2990.201881] sd 1:0:0:0: [sda] Synchronizing SCSI cache
<5>[ 2990.201909] sd 2:0:0:0: [sdb] Synchronizing SCSI cache
<5>[ 2990.201926] sd 1:0:0:0: [sda] Stopping disk
<5>[ 2990.202628] sd 2:0:0:0: [sdb] Stopping disk
<6>[ 2994.344739] ACPI: Preparing to enter system sleep state S3
Oops#1 Part3
<5>[ 2994.344811] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
<6>[ 2994.345404] PM: Saving platform NVS memory
<6>[ 2994.345460] Disabling non-boot CPUs ...
<6>[ 2994.347565] smpboot: CPU 1 is now offline
<6>[ 2994.349075] smpboot: CPU 2 is now offline
<6>[ 2994.351136] smpboot: CPU 3 is now offline
<6>[ 2994.352639] ACPI: Low-level resume complete
<6>[ 2994.352665] PM: Restoring platform NVS memory
<6>[ 2994.393134] LVT offset 0 assigned for vector 0x400
<6>[ 2994.393374] Enabling non-boot CPUs ...
<6>[ 2994.393449] x86: Booting SMP configuration:
<6>[ 2994.393449] smpboot: Booting Node 0 Processor 1 APIC 0x11
<6>[ 2994.394160] microcode: CPU1: patch_level=0x06000822
<6>[ 2994.396574] CPU1 is up
<6>[ 2994.396634] smpboot: Booting Node 0 Processor 2 APIC 0x12
<6>[ 2994.397219] microcode: CPU2: patch_level=0x06000822
<6>[ 2994.399636] CPU2 is up
<6>[ 2994.399679] smpboot: Booting Node 0 Processor 3 APIC 0x13
<6>[ 2994.400386] microcode: CPU3: patch_level=0x06000822
<6>[ 2994.402796] CPU3 is up
<6>[ 2994.407603] ACPI: Waking up from system sleep state S3
<5>[ 2994.539409] usb usb8: root hub lost power or was reset
<5>[ 2994.539411] usb usb9: root hub lost power or was reset
<6>[ 2994.539984] serial 00:03: activated
<5>[ 2994.557061] sd 1:0:0:0: [sda] Starting disk
<5>[ 2994.557086] sd 2:0:0:0: [sdb] Starting disk
<6>[ 2994.619132] r8169 0000:03:00.0 enp3s0: Link is Down
<6>[ 2994.849077] ata4: SATA link down (SStatus 0 SControl 300)
<6>[ 2994.885335] usb 8-1: reset high-speed USB device number 2 using xhci_hcd
<6>[ 2995.003150] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
<6>[ 2995.003180] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
<4>[ 2995.039287] ata3.00: NCQ Send/Recv Log not supported
<6>[ 2995.050422] ata1.00: configured for UDMA/100
Oops#1 Part2
<4>[ 2995.097769] ata3.00: NCQ Send/Recv Log not supported
<6>[ 2995.097772] ata3.00: configured for UDMA/133
<5>[ 2995.131187] firewire_core 0000:04:06.2: rediscovered device fw0
<1>[ 2995.227345] BUG: kernel NULL pointer dereference, address: 0000000000000030
<1>[ 2995.227346] #PF: supervisor read access in kernel mode
<1>[ 2995.227347] #PF: error_code(0x0000) - not-present page
<6>[ 2995.227348] PGD 0 P4D 0 
<4>[ 2995.227350] Oops: 0000 [#1] SMP NOPTI
<4>[ 2995.227352] CPU: 0 PID: 4302 Comm: kworker/u8:88 Not tainted 5.3.0-rc1+ #88
<4>[ 2995.227352] Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./970A-D3P, BIOS FC 06/01/2015
<4>[ 2995.227356] Workqueue: events_unbound async_run_entry_fn
<4>[ 2995.227366] RIP: 0010:xhci_endpoint_reset+0x74/0x2e0 [xhci_hcd]
<4>[ 2995.227367] Code: 03 49 63 84 24 10 05 00 00 41 83 e7 03 4c 8b ac c3 f8 03 00 00 75 4f 41 0f b6 6e 02 83 e5 0f 8d 44 2d 00 48 69 d0 a8 00 00 00 <41> 8b 54 15 30 f6 c2 40 74 0f 48 69 c0 a8 00 00 00 83 e2 bf 41 89
<4>[ 2995.227368] RSP: 0018:ffffb3bc81ea7c38 EFLAGS: 00010246
<4>[ 2995.227369] RAX: 0000000000000000 RBX: ffff95bf31418000 RCX: 0000000000000000
<4>[ 2995.227369] RDX: 0000000000000000 RSI: ffff95bf3398f050 RDI: ffff95bf31418000
<4>[ 2995.227370] RBP: 0000000000000000 R08: ffffffff9be1c560 R09: 0000000000000000
<4>[ 2995.227370] R10: 00000002af68b8cd R11: 0000000000000000 R12: ffff95bf3398f000
<4>[ 2995.227371] R13: 0000000000000000 R14: ffff95bf3398f050 R15: 0000000000000000
<4>[ 2995.227372] FS:  0000000000000000(0000) GS:ffff95bf36a00000(0000) knlGS:0000000000000000
<4>[ 2995.227372] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[ 2995.227373] CR2: 0000000000000030 CR3: 0000000214212000 CR4: 00000000000406f0
<4>[ 2995.227373] Call Trace:
Oops#1 Part1
<4>[ 2995.227379]  usb_enable_endpoint+0xa5/0xb0
<4>[ 2995.227381]  usb_reset_and_verify_device+0x10d/0x740
<4>[ 2995.227383]  ? _raw_spin_unlock_irqrestore+0x16/0x30
<4>[ 2995.227384]  usb_port_resume+0x596/0x780
<4>[ 2995.227386]  usb_resume_both+0x91/0x130
<4>[ 2995.227387]  usb_resume+0x21/0x80
<4>[ 2995.227388]  ? usb_dev_thaw+0x10/0x10
<4>[ 2995.227390]  dpm_run_callback+0x65/0x190
<4>[ 2995.227391]  device_resume+0xac/0x1b0
<4>[ 2995.227393]  async_resume+0x19/0x40
<4>[ 2995.227394]  async_run_entry_fn+0x4a/0x180
<4>[ 2995.227395]  process_one_work+0x185/0x3a0
<4>[ 2995.227397]  worker_thread+0x30/0x3b0
<4>[ 2995.227398]  ? process_one_work+0x3a0/0x3a0
<4>[ 2995.227399]  kthread+0x113/0x130
<4>[ 2995.227399]  ? kthread_park+0xa0/0xa0
<4>[ 2995.227400]  ret_from_fork+0x27/0x50
<4>[ 2995.227402] Modules linked in: snd_seq_dummy snd_seq_oss snd_emu10k1_synth snd_emux_synth snd_seq_midi_emul snd_seq_virmidi snd_seq_midi snd_seq_midi_event snd_seq nouveau wmi i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops usblp ttm edac_mce_amd kvm_amd drm kvm hid_logitech_hidpp irqbypass snd_hda_codec_realtek snd_emu10k1 aesni_intel snd_usb_audio snd_hda_codec_generic snd_hda_intel aes_x86_64 snd_util_mem glue_helper pcspkr crypto_simd snd_ac97_codec snd_hda_codec ac97_bus snd_usbmidi_lib efi_pstore snd_rawmidi snd_hda_core hid_logitech_dj snd_seq_device snd_hwdep xhci_pci k10temp efivars snd_pcm fam15h_power xhci_hcd ata_generic firewire_ohci snd_timer emu10k1_gp firewire_core pata_acpi snd crc_itu_t i2c_piix4 soundcore gameport pata_atiixp i2c_core acpi_cpufreq it87 hwmon_vid fuse autofs4 ghash_clmulni_intel cryptd crc32c_intel r8169 realtek libphy configfs efivarfs
<4>[ 2995.227424] CR2: 0000000000000030
<4>[ 2995.227425] ---[ end trace 0af16ad166d3b33a ]---

[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux