Hi Macpaul,
On Wed, 2019-06-12 at 14:28 +0800, Macpaul Lin wrote:
> 1. Add OTG_HNP_REQD and OTG_SRP_REQD definitions in ch9.h.
> 2. When OTG_HNP_REQD and OTG_SRP_REQD has been received,
> usb hardware must not enter TEST mode but need to response setup packet.
> 3. Add otg_srp_reqd and otg_hnp_reqd in struct ssusb_mtk for futher
> implementation.
>
> Signed-off-by: Macpaul Lin <macpaul.lin@xxxxxxxxxxxx>
> ---
> drivers/usb/mtu3/mtu3.h | 4 ++++
> drivers/usb/mtu3/mtu3_gadget_ep0.c | 13 +++++++++++++
> include/uapi/linux/usb/ch9.h | 5 +++++
> 3 files changed, 22 insertions(+)
The driver currently doesn't support HNP/SRP, so there will be something
wrong when connected with PET to run compliance test, and I prefer not
to support it, because it's rarely used in normal case, thanks
>
> diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
> index 76ecf12fdf62..bb8a31bc6e4d 100644
> --- a/drivers/usb/mtu3/mtu3.h
> +++ b/drivers/usb/mtu3/mtu3.h
> @@ -226,6 +226,8 @@ struct otg_switch_mtk {
> * @dma_clk: dma_bus_ck clock for AXI bus etc
> * @dr_mode: works in which mode:
> * host only, device only or dual-role mode
> + * @otg_srp_reqd: used for SRP request handling.
> + * @otg_hnp_reqd: used for HNP request handling.
> * @u2_ports: number of usb2.0 host ports
> * @u3_ports: number of usb3.0 host ports
> * @u3p_dis_msk: mask of disabling usb3 ports, for example, bit0==1 to
> @@ -252,6 +254,8 @@ struct ssusb_mtk {
> /* otg */
> struct otg_switch_mtk otg_switch;
> enum usb_dr_mode dr_mode;
> + bool otg_srp_reqd;
> + bool otg_hnp_reqd;
> bool is_host;
> int u2_ports;
> int u3_ports;
> diff --git a/drivers/usb/mtu3/mtu3_gadget_ep0.c b/drivers/usb/mtu3/mtu3_gadget_ep0.c
> index 4da216c99726..1247c43a63e6 100644
> --- a/drivers/usb/mtu3/mtu3_gadget_ep0.c
> +++ b/drivers/usb/mtu3/mtu3_gadget_ep0.c
> @@ -285,11 +285,24 @@ static int handle_test_mode(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
> dev_dbg(mtu->dev, "TEST_PACKET\n");
> mtu->test_mode_nr = TEST_PACKET_MODE;
> break;
> + case OTG_SRP_REQD:
> + dev_dbg(mtu->dev, "OTG_SRP_REQD\n");
> + mtu->ssusb->otg_srp_reqd = 1;
> + break;
> + case OTG_HNP_REQD:
> + dev_dbg(mtu->dev, "OTG_HNP_REQD\n");
> + mtu->ssusb->otg_hnp_reqd = 1;
> + break;
> default:
> handled = -EINVAL;
> goto out;
> }
>
> + if (mtu->ssusb->otg_srp_reqd || mtu->ssusb->otg_hnp_reqd) {
> + mtu->ep0_state = MU3D_EP0_STATE_SETUP;
> + goto out;
> + }
> +
> mtu->test_mode = true;
>
> /* no TX completion interrupt, and need restart platform after test */
> diff --git a/include/uapi/linux/usb/ch9.h b/include/uapi/linux/usb/ch9.h
> index d5a5caec8fbc..545918c83fd1 100644
> --- a/include/uapi/linux/usb/ch9.h
> +++ b/include/uapi/linux/usb/ch9.h
> @@ -143,6 +143,11 @@
> #define TEST_SE0_NAK 3
> #define TEST_PACKET 4
> #define TEST_FORCE_EN 5
> +/*
> + * OTG HNP and SRP REQD
> + */
> +#define OTG_SRP_REQD 6
> +#define OTG_HNP_REQD 7
>
> /* Status Type */
> #define USB_STATUS_TYPE_STANDARD 0
