Add device-tree binding documentation for the XUSB device mode controller
present on Tegra210 SoC. This controller supports the USB 3.0
specification.
Signed-off-by: Nagarjuna Kristam <nkristam@xxxxxxxxxx>
Reviewed-by: JC Kuo <jckuo@xxxxxxxxxx>
---
.../devicetree/bindings/usb/nvidia,tegra-xudc.txt | 108 +++++++++++++++++++++
1 file changed, 108 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
new file mode 100644
index 0000000..cde4e11
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
@@ -0,0 +1,108 @@
+Device tree binding for NVIDIA Tegra XUSB device mode controller (XUDC)
+=======================================================================
+
+The Tegra XUDC controller supports both USB 2.0 HighSpeed/FullSpeed and
+USB 3.0 SuperSpeed protocols.
+
+Required properties:
+--------------------
+- compatible: For Tegra210, must contain "nvidia,tegra210-xudc".
+- reg: Must contain the base and length of the XUSB device registers, XUSB device
+ PCI Config registers and XUSB device controller registers.
+- reg-names: Must include all the register names needed for the driver
+- interrupts: Must contain the XUSB device interrupt.
+- clocks: Must contain an entry for all clocks used.
+ See ../clock/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - dev: Clock to enable core XUSB dev clock.
+ - ss: Clock to enable XUSB super speed clock.
+ - ss_src: Clock to enable XUSB super speed dev clock.
+ - hs_src: Clock to enable XUSB high speed dev clock.
+ - fs_src: Clock to enable XUSB full speed dev clock.
+- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to
+ configure the USB pads used by the XUDC controller.
+- power-domains: A list of PM domain specifiers that reference each power-domain
+ used by the XUSB device mode controller. This list must comprise of a specifier
+ for the XUSBA and XUSBB power-domains. See ../power/power_domain.txt and
+ ../arm/tegra/nvidia,tegra20-pmc.txt for details.
+- power-domain-names: A list of names that represent each of the specifiers in
+ the 'power-domains' property. Must include 'ss' and 'dev'.
+- phys: Must contain an entry for each entry in phy-names.
+ See ../phy/phy-bindings.txt for details.
+- phy-names: Should include an entry for each PHY used by the controller.
+ Names must be "usb2", and "usb3" if support SuperSpeed device mode.
+ - "usb3" phy, SuperSpeed (SSTX+/SSTX-/SSRX+/SSRX-) data lines.
+ - "usb2" phy, USB 2.0 (D+/D-) data lines.
+
+For Tegra210:
+- avddio-usb-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V.
+- hvdd-usb-supply: USB controller power supply. Must supply 3.3 V.
+
+
+Optional properties:
+--------------------
+- usb-role-switch: boolean property to indicate use of USB Role Switch driver.
+
+Sub-nodes:
+----------
+- The port would be added as subnode if use "usb-role-switch" property.
+ see graph.txt.
+
+Example:
+--------
+ pmc: pmc@7000e400 {
+ compatible = "nvidia,tegra210-pmc";
+ reg = <0x0 0x7000e400 0x0 0x400>;
+ clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
+ clock-names = "pclk", "clk32k_in";
+
+ powergates {
+ pd_xusbss: xusba {
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
+ resets = <&tegra_car 156>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_xusbdev: xusbb {
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
+ resets = <&tegra_car 95>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+
+ xudc@700d0000 {
+ compatible = "nvidia,tegra210-xudc";
+ reg = <0x0 0x700d0000 0x0 0x8000>,
+ <0x0 0x700d8000 0x0 0x1000>,
+ <0x0 0x700d9000 0x0 0x1000>;
+ reg-names = "base", "fpci", "ipfs";
+
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>,
+ <&tegra_car TEGRA210_CLK_XUSB_SS>,
+ <&tegra_car TEGRA210_CLK_XUSB_SSP_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
+ <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>;
+ clock-names = "dev", "ss", "ss_src", "hs_src", "fs_src";
+
+ power-domains = <&pd_xusbdev>, <&pd_xusbss>;
+ power-domain-names = "dev", "ss";
+
+ nvidia,xusb-padctl = <&padctl>;
+
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>;
+ phy-names = "usb2;
+
+ avddio-usb-supply = <&vdd_pex_1v05>;
+ hvdd-usb-supply = <&vdd_3v3_sys>;
+
+ usb-role-switch;
+ port {
+ usb_role_switch: endpoint@0 {
+ remote-endpoint = <&bconn_ep>;
+ };
+ };
+
+ };
--
2.7.4
