On Fri, Jun 7, 2019 at 4:04 PM Alan Stern <stern@xxxxxxxxxxxxxxxxxxx> wrote:
>
> On Fri, 7 Jun 2019, Andrey Konovalov wrote:
>
> > On Fri, Jun 7, 2019 at 2:43 PM Felipe Balbi
> > <felipe.balbi@xxxxxxxxxxxxxxx> wrote:
> > >
> > >
> > > Hi,
> > >
> > > Andrey Konovalov <andreyknvl@xxxxxxxxxx> writes:
> > > >> >> Andrey Konovalov <andreyknvl@xxxxxxxxxx> writes:
> > > >> >> > I've noticed that when the host performs a control request,
> > > >> >> > urb->transfer_buffer/transfer_buffer_length are not passed to the
> > > >> >> > gadget drivers via the setup() call, the only thing that is passed is
> > > >> >> > the usb_ctrlrequest struct. Is there a way to get the transfer_buffer
> > > >> >> > from within a gadget driver? If not, what approach would the best to
> > > >> >> > implement this?
> > > >> >>
> > > >> >> I think you need to further explain what you mean here.
> > > >> >>
> > > >> >> What do you mean by gadget driver in this case?
> > > >> >>
> > > >> >> If you mean the drivers under drivers/usb/gadget/{function,legacy}
> > > >> >> directories then there's no way that they can have access to anything
> > > >> >> from the host.
> > > >> >>
> > > >> >> Remember that gadget and host are two completely distinct units. The
> > > >> >> only thing they share is a USB cable. When it comes to Control
> > > >> >> Transfers, if a data stage is necessary, that must be encoded in the
> > > >> >> wLength field of the control structure.
> > > >> >>
> > > >> >> Also, host side does *not* pass its usb_ctrlrequest struct to the
> > > >> >> gadget, it passes a series of 8 bytes which are oblivious to where in
> > > >> >> memory they were from the host point of view.
> > > >> >>
> > > >> >> If if you have the same machine acting as both host and device, each
> > > >> >> side has no knowledge of that fact.
> > > >> >
> > > >> > Hi Felipe,
> > > >> >
> > > >> > What I meant is that any module (gadget driver) that implements
> > > >> > usb_gadget_driver struct callbacks and registers it, will only get
> > > >> > usb_ctrlrequest through the setup() callback, but not the
> > > >> > transfer_buffer/length.
> > > >>
> > > >> A control request is *always* 8 bytes. That's mandated by the USB
> > > >> specification.
> > > >>
> > > >> > And therefore it can't access the data that is
> > > >> > attached to a control request.
> > > >>
> > > >> There is no data attached to a control request. A Control Transfer is
> > > >> composed of 2 or 3 stages:
> > > >>
> > > >> - SETUP stage
> > > >> an 8 byte transfer descriptor type thing
> > > >>
> > > >> - (optional) Data stage
> > > >> if wLength of control request contains a value > 0, then this
> > > >> stage fires up to transfer the amount of data communicated in
> > > >> wLength (during previous stage).
> > > >>
> > > >> - Status Stage
> > > >> A zero length transfer to communicate successful end of transfer
> > > >> (in case it completes fine) or an error (in case of STALL
> > > >> condition).
> > > >
> > > > Hm, then why does the usb_control_msg() function accepts a data and
> > > > size arguments? Which are described in the comment as "pointer to the
> > > > data to send" and "length in bytes of the data to send" accordingly?
> > > > Or is this the buffer for the response?
> > >
> > > That's for the data stage :-)
> >
> > Sure =)
> >
> > >
> > > usb_control_msg() is an upper lever API to encode and entire Control
> > > Transfer (all stages of it).
> > >
> > > What is the problem you see, then?
> >
> > The problem is that I want to receive that data (from the data stage)
> > from within my gadget driver module. But it's not passed to the
> > setup() callback. And the question is: how do I do that then?
>
> I just caught up on this thread...
>
> The answer is simple: The gadget driver's setup() callback routine
> submits a request for endpoint 0. The Data Stage data is sent or
> received (depending on the direction encoded in the Setup information)
> by this request.
Ah, OK, got it, thanks!
Although while looking at the dummy_hcd implementation, I saw that it
accesses usb->transfer_buffer in case USB_REQ_GET_STATUS in
handle_control_request(), which is called right before the setup()
callback is called. So the data already available there without any
additional requests. Is this an implementation detail that is specific
to dummy_hcd?
>
> Alan Stern
>
