On Wed, 8 May 2019, Jim Lin wrote:
> USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt
> processing for full-/low-speed endpoints connected via a TT, the host
> software must use the Clear_TT_Buffer request to the TT to ensure
> that the buffer is not in the busy state".
>
> In our case, a full-speed speaker (ConferenceCam) is behind a high-
> speed hub (ConferenceCam Connect), sometimes once we get STALL on a
> request we may continue to get STALL with the folllowing requests,
> like Set_Interface.
>
> Solution is for XHCI driver to invoke usb_hub_clear_tt_buffer() to
> send Clear_TT_Buffer request to the hub of the device for the
> following Set_Interface requests to the device to get ACK
> successfully.
>
> The Clear_TT_Buffer request sent to the hub includes the address of
> the LS/FS child device in wValue field. usb_hub_clear_tt_buffer()
> uses udev->devnum to set the address wValue. This won't work for
> devices connected to xHC.
>
> For other host controllers udev->devnum is the same as the address of
> the usb device, chosen and set by usb core. With xHC the controller
> hardware assigns the address, and won't be the same as devnum.
>
> In the fix we get that address from slot context if it's XHC.
>
> Signed-off-by: Jim Lin <jilin@xxxxxxxxxx>
> ---
> v2: xhci_clear_tt_buffer_complete: add static, shorter indentation
> , remove its claiming in xhci.h
> v3: Add description for clearing_tt (xhci.h)
> v4: Remove clearing_tt flag because hub_tt_work has hub->tt.lock
> to protect for Clear_TT_Buffer to be run serially.
> Remove xhci_clear_tt_buffer_complete as it's not necessary.
> Same reason as the above.
> Extend usb_hub_clear_tt_buffer parameter
> v5: Not extending usb_hub_clear_tt_buffer parameter
> Add description.
> v6: Remove unused parameter slot_id from xhci_clear_hub_tt_buffer
>
> drivers/usb/core/hub.c | 17 ++++++++++++++++-
> drivers/usb/host/xhci-ring.c | 12 ++++++++++++
> 2 files changed, 28 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> index 15a2934dc29d..00d994908217 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -35,6 +35,7 @@
>
> #include "hub.h"
> #include "otg_whitelist.h"
> +#include "../host/xhci.h"
>
> #define USB_VENDOR_GENESYS_LOGIC 0x05e3
> #define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND 0x01
> @@ -858,6 +859,10 @@ int usb_hub_clear_tt_buffer(struct urb *urb)
> struct usb_tt *tt = udev->tt;
> unsigned long flags;
> struct usb_tt_clear *clear;
> + struct xhci_hcd *xhci;
> + struct xhci_virt_device *dev;
> + struct xhci_slot_ctx *slot_ctx;
> + int devnum;
>
> /* we've got to cope with an arbitrary number of pending TT clears,
> * since each TT has "at least two" buffers that can need it (and
> @@ -873,7 +878,17 @@ int usb_hub_clear_tt_buffer(struct urb *urb)
> /* info that CLEAR_TT_BUFFER needs */
> clear->tt = tt->multi ? udev->ttport : 1;
> clear->devinfo = usb_pipeendpoint (pipe);
> - clear->devinfo |= udev->devnum << 4;
> + /* If slot_id is nonzero, then it's XHCI */
> + if (udev->slot_id) {
> + xhci = hcd_to_xhci(bus_to_hcd(udev->bus));
> + dev = xhci->devs[udev->slot_id];
> + slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx);
> + /* Device address is assigned by XHC */
> + devnum = (int) le32_to_cpu(slot_ctx->dev_state) &
> + DEV_ADDR_MASK;
> + clear->devinfo |= devnum << 4;
This is a horrendous layering violation! The hub driver shouldn't need
to know anything about how the xHCI driver works.
Please don't do it this way. Instead, add a field to store the
hardware address in the usb_device structure, as discussed earlier.
Alan Stern
> + } else
> + clear->devinfo |= udev->devnum << 4;
> clear->devinfo |= usb_pipecontrol(pipe)
> ? (USB_ENDPOINT_XFER_CONTROL << 11)
> : (USB_ENDPOINT_XFER_BULK << 11);
> diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
> index 9215a28dad40..739737faf752 100644
> --- a/drivers/usb/host/xhci-ring.c
> +++ b/drivers/usb/host/xhci-ring.c
> @@ -1786,6 +1786,17 @@ struct xhci_segment *trb_in_td(struct xhci_hcd *xhci,
> return NULL;
> }
>
> +static void xhci_clear_hub_tt_buffer(struct xhci_hcd *xhci, struct xhci_td *td)
> +{
> + /*
> + * As part of low/full-speed endpoint-halt processing
> + * we must clear the TT buffer (USB 2.0 specification 11.17.5).
> + */
> + if (td->urb->dev->tt && !usb_pipeint(td->urb->pipe) &&
> + (td->urb->dev->tt->hub != xhci_to_hcd(xhci)->self.root_hub))
> + usb_hub_clear_tt_buffer(td->urb);
> +}
> +
> static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
> unsigned int slot_id, unsigned int ep_index,
> unsigned int stream_id, struct xhci_td *td,
> @@ -1804,6 +1815,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
> if (reset_type == EP_HARD_RESET) {
> ep->ep_state |= EP_HARD_CLEAR_TOGGLE;
> xhci_cleanup_stalled_ring(xhci, ep_index, stream_id, td);
> + xhci_clear_hub_tt_buffer(xhci, td);
> }
> xhci_ring_cmd_db(xhci);
> }
>
