On Mon, Mar 11, 2019 at 04:41:52PM +0530, Nagarjuna Kristam wrote:
> Add device-tree binding documentation for the XUSB device mode controller
> present on tegra210 SoC. This controller supports USB 3.0 specification
>
> Based on work by Andrew Bresticker <abrestic@xxxxxxxxxxxx>.
>
> Signed-off-by: Nagarjuna Kristam <nkristam@xxxxxxxxxx>
> ---
> .../devicetree/bindings/usb/nvidia,tegra-xudc.txt | 105 +++++++++++++++++++++
> 1 file changed, 105 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
Hi Nagarjuna,
when you resend this, make sure to Cc devicetree@xxxxxxxxxxxxxxx on this
patch. We need review from one of the device tree bindings maintainers
before this can be applied, and they won't review if they don't receive
the patch. =)
Thierry
>
> diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
> new file mode 100644
> index 0000000..990655d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
> @@ -0,0 +1,105 @@
> +Device tree binding for NVIDIA Tegra XUSB device mode controller (XUDC)
> +=======================================================================
> +
> +The Tegra XUDC controller supports both USB 2.0 HighSpeed/FullSpeed and
> +USB 3.0 SuperSpeed protocols.
> +
> +Required properties:
> +--------------------
> +- compatible: For Tegra210, must contain "nvidia,tegra210-xudc".
> +- reg: Must contain the base and length of the XUSB device registers, XUSB device
> + PCI Config registers and XUSB device controller registers.
> +- interrupts: Must contain the XUSB device interrupt
> +- clocks: Must contain an entry for ell clocks used.
> + See ../clock/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - xusb_device
> + - xusb_ss
> + - xusb_ss_src
> + - xusb_hs_src
> + - xusb_fs_src
> +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to
> + configure the USB pads used by the XUDC controller
> +- power-domains: A list of PM domain specifiers that reference each power-domain
> + used by the XUSB device mode controller. This list must comprise of a specifier
> + for the XUSBA and XUSBB power-domains. See ../power/power_domain.txt and
> + ../arm/tegra/nvidia,tegra20-pmc.txt for details.
> +- power-domain-names: A list of names that represent each of the specifiers in
> + the 'power-domains' property. Must include 'xusb_ss' and 'xusb_device'
> +
> +For Tegra210:
> +- avddio-usb-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V.
> +- hvdd-usb-supply: USB controller power supply. Must supply 3.3 V.
> +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
> +
> +- phys: Must contain an entry for each entry in phy-names.
> + See ../phy/phy-bindings.txt for details.
> +- extcon-usb: Must contains an extcon-usb entry which detects
> + USB VBUS pin. See ../extcon/extcon-usb-gpio.txt for details.
> +
> +Optional properties:
> +--------------------
> +- phy-names: Should include an entry for each PHY used by the controller.
> + Names must be "usb2", and "usb3" if support SuperSpeed device mode.
> + - "usb3" phy, SuperSpeed (SSTX+/SSTX-/SSRX+/SSRX-) data lines
> + - "usb2" phy, USB 2.0 (D+/D-) data lines
> +
> +Example:
> +--------
> + pmc: pmc@7000e400 {
> + compatible = "nvidia,tegra210-pmc";
> + reg = <0x0 0x7000e400 0x0 0x400>;
> + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
> + clock-names = "pclk", "clk32k_in";
> +
> + powergates {
> + pd_xusbss: xusba {
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
> + resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
> + #power-domain-cells = <0>;
> + };
> +
> + pd_xusbdev: xusbb {
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
> + resets = <&tegra_car 95>;
> + #power-domain-cells = <0>;
> + };
> + };
> + };
> +
> + xudc@700d0000 {
> + compatible = "nvidia,tegra210-xudc";
> + reg = <0x0 0x700d0000 0x0 0x8000>,
> + <0x0 0x700d8000 0x0 0x1000>,
> + <0x0 0x700d9000 0x0 0x1000>;
> +
> + interrupts = <0 44 0x4>;
> +
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>,
> + <&tegra_car TEGRA210_CLK_XUSB_SS>,
> + <&tegra_car TEGRA210_CLK_XUSB_SSP_SRC>,
> + <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
> + <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>;
> + clock-names = "xusb_device", "xusb_ss", "xusb_ss_src",
> + "xusb_hs_src", "xusb_fs_src";
> +
> + power-domains = <&pd_xusbdev>, <&pd_xusbss>;
> + power-domain-names = "xusb_device", "xusb_ss";
> +
> + nvidia,xusb-padctl = <&padctl>;
> +
> + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>;
> + phy-names = "usb2;
> +
> + avddio-usb-supply = <&vdd_pex_1v05>;
> + hvdd-usb-supply = <&vdd_3v3_sys>;
> + avdd-pll-utmip-supply = <&vdd_1v8>;
> +
> + extcon = <&extcon_usb>;
> + };
> +
> + extcon_usb: extcon_vbus {
> + compatible = "linux,extcon-usb-gpio";
> + vbus-gpio = <&gpio TEGRA_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
> + };
> +
> --
> 2.7.4
>
Attachment:
signature.asc
Description: PGP signature
