Re: [PATCH 1/5] dt-bindings: connector: add optional properties for Type-B

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On 12-03-19 04:18, Chunfeng Yun wrote:
Hi,
On Mon, 2019-03-11 at 09:06 +0100, Hans de Goede wrote:
Hi,

On 11-03-19 06:33, Chunfeng Yun wrote:
Hi,

On Fri, 2019-03-08 at 13:07 +0100, Hans de Goede wrote:
Hi,

On 08-03-19 07:13, Chunfeng Yun wrote:
Add id-gpios, vbus-gpios, vbus-supply and pinctrl properties for
usb-b-connector

Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
    .../devicetree/bindings/connector/usb-connector.txt    | 10 ++++++++++
    1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt
index a9a2f2fc44f2..7a07b0f4f973 100644
--- a/Documentation/devicetree/bindings/connector/usb-connector.txt
+++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
@@ -17,6 +17,16 @@ Optional properties:
    - self-powered: Set this property if the usb device that has its own power
      source.
+Optional properties for usb-b-connector:
+- id-gpios: gpio for USB ID pin.

What about boards where the ID pin is *not* connected to a GPIO,
but e.g. to a special pin on the PMIC which can also detect
an ACA adapter ? Currently this case is handled by extcon
drivers, but we have no way to set e.g. vbus-supply for the
connector. Maybe in this case the usb-connector node should
be a child of the PMIC node ?
Yes, it would be, PMIC is in charger of detecting the status of ID pin

Ok, then I think this should be documented too.

And in many cases there also is a mux to switch the datalines
between the host and device(gadget) controllers, how should
that be described in this model?  See the new usb-role-switch
code under drivers/usb/roles

In some cases the mux is controlled through a gpio, so we
may want to add a "mux-gpios" here in which case we also
need to define what 0/1 means.
I'm not sure, the mux seems not belong to this connector,
and may need another driver to register usb-role-switch,
similar to:

[v2,2/2] usb: typec: add typec switch via GPIO control
https://patchwork.kernel.org/patch/10834327/

Right the mux/role-switch will need a driver, but the "owner"
of the usb_connector, e.g. the PMIC or the owner of the
id GPIO pin needs to know which device is the role-switch so
that it can set the role correctly based on the id-pin.

Your binding already contains Vbus info, allowing the owner
of the usb_connector to enable/disable Vbus based on the id-pin,
but the owner will also be responsible for setting the role-switch.
In this patch series, I make usb_connector driver enable/disable Vbus,
but not the parent(USB controller) of usb_connector which registers a
usb-role-switch, which way do you think it is better?

IMHO there should not be a driver for the usb_connector child-node,
only for the parent-device of that child-node.

There are going to be too many specific setups surrounding PMICs to
be able to do a single generic driver for the connector.

Regards,

Hans




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux