[Resend with From address corrected. Sorry about that]
Johan,
Some of our customers are experiencing communication issues on RS485
that could be solved quite nicely by turning on termios.PARMRK. I'd
be happy to go into details, but I don't think they're necessary for
the discussion below.
The problem we encountered is that the error flagging produced by
ftdi_sio.c over-marks errors to the point that PARMRK becomes unusable
(in our cases, everything ends up being flagged as errors, even the
actual, good data).
The issue in particular is that the driver marks *all* characters
received in a single USB packet with an error flag based on whether a
BREAK, frame error, or parity error condition is reported by that USB
packet. In actuality, the FTDI chip's error condition seems to apply
to the last byte in the received packet (I tested with an FT230X
chip). Unfortunately, it's more complicated than that. I was unable
to find any useful documentation on the USB packets the FTDI chips
generate, but from trial and error, the BREAK condition handling seems
to work something like this:
When a break condition is reported (FTDI_RS_BI is set), the
last byte received MAY be a BREAK. To confirm, wait for the
next status packet. IF that status packet has no data AND
FTDI_RS_BI is still set, then the previous character was
indeed a BREAK. Otherwise, the previous character was a
normal data byte.
This seems rather byzantine, but in my testing, it's been the only
algorithm that was able to accurately identify BREAKs.
I attached some code that worked for the test cases I tried. Of
course, I'm not overly confident that this will work in all cases.
As for parity errors: I have not been able to figure out how to mark
ALL parity errors characters without also sometimes accidentally
marking correctly received bytes as erroneous.
My sense is that the FTDI chips simply can't reliably flag all error
characters (and only error characters) and we're probably not going to
use PARMRK to try to handle the communications issue mentioned at the
outset, so I'm on the fence whether is worthwhile to apply a patch
along the lines of the below. However, I'd suggest that at least a
comment be added in the driver making it clear that the error flagging
is not accurate as implemented and that it will mark too many
characters as erroneous, but that, perhaps, it's the best that can be
done.
Thoughts?
--david
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 2e2f736384ab..aca2613225f3 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -65,6 +65,8 @@ struct ftdi_private {
int flags; /* some ASYNC_xxxx flags are supported */
unsigned long last_dtr_rts; /* saved modem control outputs */
char prev_status; /* Used for TIOCMIWAIT */
+ char prev_errs;
+ char held;
char transmit_empty; /* If transmitter is empty or not */
__u16 interface; /* FT2232C, FT2232H or FT4232H port interface
(0 for FT232/245) */
@@ -2045,6 +2047,7 @@ static int ftdi_process_packet(struct usb_serial_port *port,
int i;
char status;
char flag;
+ char errs;
char *ch;
if (len < 2) {
@@ -2086,6 +2089,21 @@ static int ftdi_process_packet(struct usb_serial_port *port,
else
priv->transmit_empty = 0;
+ if (priv->prev_errs) {
+ errs = priv->prev_errs & packet[1];
+ flag = TTY_NORMAL;
+ if ((len <= 2) && (errs & FTDI_RS_BI)) {
+ printk("BREAK\n");
+ flag = TTY_BREAK;
+ port->icount.brk++;
+ usb_serial_handle_break(port);
+ }
+ printk("%s: flag=%d data=%02x\n", __func__, flag, priv->held);
+ tty_insert_flip_char(&port->port, priv->held, flag);
+ ++port->icount.rx;
+ priv->prev_errs = 0;
+ }
+
len -= 2;
if (!len)
return 0; /* status only */
@@ -2094,18 +2112,22 @@ static int ftdi_process_packet(struct usb_serial_port *port,
* Break and error status must only be processed for packets with
* data payload to avoid over-reporting.
*/
+ errs = packet[1] & FTDI_RS_ERR_MASK;
flag = TTY_NORMAL;
- if (packet[1] & FTDI_RS_ERR_MASK) {
- /* Break takes precedence over parity, which takes precedence
- * over framing errors */
- if (packet[1] & FTDI_RS_BI) {
- flag = TTY_BREAK;
- port->icount.brk++;
- usb_serial_handle_break(port);
- } else if (packet[1] & FTDI_RS_PE) {
+ ch = packet + 2;
+ if (errs) {
+ if (errs & FTDI_RS_BI) {
+ priv->prev_errs = errs;
+ priv->held = ch[len - 1];
+ if (--len == 0)
+ return 0;
+ }
+ if (errs & FTDI_RS_PE) {
+ printk("PARITY\n");
flag = TTY_PARITY;
port->icount.parity++;
- } else if (packet[1] & FTDI_RS_FE) {
+ } else if (errs & FTDI_RS_FE) {
+ printk("FRAME\n");
flag = TTY_FRAME;
port->icount.frame++;
}
@@ -2116,8 +2138,19 @@ static int ftdi_process_packet(struct usb_serial_port *port,
}
}
+
port->icount.rx += len;
- ch = packet + 2;
+
+ {
+ char buf[128], *dst = buf, *end = &buf[128];
+ int i;
+
+ for (i = 0; i < len; ++i) {
+ snprintf (dst, end - dst, " %02x", ch[i]);
+ dst += 3;
+ }
+ printk("%s: flag=%d data=[%s ]\n", __func__, flag, buf);
+ }
if (port->port.console && port->sysrq) {
for (i = 0; i < len; i++, ch++) {
