Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
The PHYs are childen of the Glue node since the Glue controls the interface
with the PHY, not the DWC3 controller.
The drivers collects the mode of each PHY and determine which PHY
is to be routed between the DWC2 and DWC3 controllers.
This drivers supports the on-probe setup of the OTG mode, and manually
via a debugfs interface. The IRQ mode change detect is yet to be added
in a future patchset, mainly due to lack of hardware to validate on.
Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
---
drivers/usb/dwc3/Kconfig | 9 +
drivers/usb/dwc3/Makefile | 1 +
drivers/usb/dwc3/dwc3-meson-g12a.c | 650 +++++++++++++++++++++++++++++
3 files changed, 660 insertions(+)
create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index 1a0404fda596..4335e5e76bbb 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -93,6 +93,15 @@ config USB_DWC3_KEYSTONE
Support of USB2/3 functionality in TI Keystone2 platforms.
Say 'Y' or 'M' here if you have one such device
+config USB_DWC3_MESON_G12A
+ tristate "Amlogic Meson G12A Platforms"
+ depends on OF && COMMON_CLK
+ depends on ARCH_MESON || COMPILE_TEST
+ default USB_DWC3
+ help
+ Support USB2/3 functionality in Amlogic G12A platforms.
+ Say 'Y' or 'M' if you have one such device.
+
config USB_DWC3_OF_SIMPLE
tristate "Generic OF Simple Glue Layer"
depends on OF && COMMON_CLK
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index 6e3ef6144e5d..ae86da0dc5bd 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
new file mode 100644
index 000000000000..abeff2d56b1d
--- /dev/null
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * USB Glue for Amlogic G12A SoCs
+ *
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
+ */
+
+/*
+ * The USB is organized with a glue around the DWC3 Controller IP as :
+ * - Control registers for each USB2 Ports
+ * - Control registers for the USB PHY layer
+ * - SuperSpeed PHY can be enabled only if port is used
+ *
+ * TOFIX:
+ * - Add dynamic OTG switching with ID change interrupt
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/reset.h>
+#include <linux/of_graph.h>
+#include <linux/phy/phy.h>
+#include <linux/usb/otg.h>
+#include <linux/debugfs.h>
+
+/* USB Glue Control Registers */
+
+#define USB_R0 0x00
+ #define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17)
+ #define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18)
+ #define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19)
+ #define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29)
+ #define USB_R0_U2D_ACT BIT(31)
+
+#define USB_R1 0x04
+ #define USB_R1_U3H_BIGENDIAN_GS BIT(0)
+ #define USB_R1_U3H_PME_ENABLE BIT(1)
+ #define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(4, 2)
+ #define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(9, 7)
+ #define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(13, 12)
+ #define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16)
+ #define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17)
+ #define USB_R1_U3H_HOST_MSI_ENABLE BIT(18)
+ #define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19)
+ #define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25)
+
+#define USB_R2 0x08
+ #define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20)
+ #define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26)
+
+#define USB_R3 0x0c
+ #define USB_R3_P30_SSC_ENABLE BIT(0)
+ #define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1)
+ #define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4)
+ #define USB_R3_P30_REF_SSP_EN BIT(13)
+
+#define USB_R4 0x10
+ #define USB_R4_P21_PORT_RESET_0 BIT(0)
+ #define USB_R4_P21_SLEEP_M0 BIT(1)
+ #define USB_R4_MEM_PD_MASK GENMASK(3, 2)
+ #define USB_R4_P21_ONLY BIT(4)
+
+#define USB_R5 0x14
+ #define USB_R5_ID_DIG_SYNC BIT(0)
+ #define USB_R5_ID_DIG_REG BIT(1)
+ #define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2)
+ #define USB_R5_ID_DIG_EN_0 BIT(4)
+ #define USB_R5_ID_DIG_EN_1 BIT(5)
+ #define USB_R5_ID_DIG_CURR BIT(6)
+ #define USB_R5_ID_DIG_IRQ BIT(7)
+ #define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8)
+ #define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16)
+
+/* USB2 Ports Control Registers */
+
+#define U2P_R0 0x0
+ #define U2P_R0_HOST_DEVICE BIT(0)
+ #define U2P_R0_POWER_OK BIT(1)
+ #define U2P_R0_HAST_MODE BIT(2)
+ #define U2P_R0_POWER_ON_RESET BIT(3)
+ #define U2P_R0_ID_PULLUP BIT(4)
+ #define U2P_R0_DRV_VBUS BIT(5)
+
+#define U2P_R1 0x4
+ #define U2P_R1_PHY_READY BIT(0)
+ #define U2P_R1_ID_DIG BIT(1)
+ #define U2P_R1_OTG_SESSION_VALID BIT(2)
+ #define U2P_R1_VBUS_VALID BIT(3)
+
+#define MAX_PHY 5
+
+#define USB2_MAX_PHY 4
+#define USB3_PHY 4
+
+struct dwc3_meson_g12a {
+ struct device *dev;
+ struct regmap *regmap;
+ struct clk *clk;
+ struct reset_control *reset;
+ struct phy *phys[5];
+ enum usb_dr_mode phy_modes[5];
+ enum phy_mode otg_phy_mode;
+ unsigned int usb2_ports;
+ unsigned int usb3_ports;
+ struct dentry *root;
+};
+
+#define U2P_REG_SIZE 0x20
+#define USB_REG_OFFSET 0x80
+
+static void dwc3_meson_g12a_usb2_set_mode(struct dwc3_meson_g12a *priv,
+ int i, enum usb_dr_mode mode)
+{
+ switch (mode) {
+ case USB_DR_MODE_HOST:
+ case USB_DR_MODE_OTG:
+ case USB_DR_MODE_UNKNOWN:
+ regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+ U2P_R0_HOST_DEVICE,
+ U2P_R0_HOST_DEVICE);
+ break;
+
+ case USB_DR_MODE_PERIPHERAL:
+ regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+ U2P_R0_HOST_DEVICE, 0);
+ break;
+ }
+}
+
+static int dwc3_meson_g12a_usb2_init(struct dwc3_meson_g12a *priv)
+{
+ enum usb_dr_mode id_mode;
+ u32 val;
+ int i;
+
+ /* Read ID current level */
+ regmap_read(priv->regmap, USB_R5, &val);
+ if (val & USB_R5_ID_DIG_CURR)
+ id_mode = USB_DR_MODE_PERIPHERAL;
+ else
+ id_mode = USB_DR_MODE_HOST;
+
+ dev_info(priv->dev, "ID mode %s\n",
+ id_mode == USB_DR_MODE_HOST ? "host" : "peripheral");
+
+ for (i = 0 ; i < USB2_MAX_PHY ; ++i) {
+ if (!priv->phys[i])
+ continue;
+
+ regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+ U2P_R0_POWER_ON_RESET,
+ U2P_R0_POWER_ON_RESET);
+
+ if (priv->phy_modes[i] == USB_DR_MODE_PERIPHERAL ||
+ (priv->phy_modes[i] == USB_DR_MODE_OTG &&
+ id_mode == USB_DR_MODE_PERIPHERAL)) {
+ dwc3_meson_g12a_usb2_set_mode(priv, i,
+ USB_DR_MODE_PERIPHERAL);
+
+ if (priv->phy_modes[i] == USB_DR_MODE_OTG)
+ priv->otg_phy_mode = PHY_MODE_USB_DEVICE;
+ } else {
+ dwc3_meson_g12a_usb2_set_mode(priv, i,
+ USB_DR_MODE_HOST);
+
+ if (priv->phy_modes[i] == USB_DR_MODE_OTG)
+ priv->otg_phy_mode = PHY_MODE_USB_HOST;
+ }
+
+ regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
+ U2P_R0_POWER_ON_RESET, 0);
+ }
+
+ return 0;
+}
+
+static void dwc3_meson_g12a_usb3_init(struct dwc3_meson_g12a *priv)
+{
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R3,
+ USB_R3_P30_SSC_RANGE_MASK |
+ USB_R3_P30_REF_SSP_EN,
+ USB_R3_P30_SSC_ENABLE |
+ FIELD_PREP(USB_R3_P30_SSC_RANGE_MASK, 2) |
+ USB_R3_P30_REF_SSP_EN);
+ udelay(2);
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R2,
+ USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK,
+ FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 0x15));
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R2,
+ USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK,
+ FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 0x20));
+
+ udelay(2);
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R1,
+ USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT,
+ USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT);
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R1,
+ USB_R1_P30_PCS_TX_SWING_FULL_MASK,
+ FIELD_PREP(USB_R1_P30_PCS_TX_SWING_FULL_MASK, 127));
+}
+
+static void dwc3_meson_g12a_usb_init_mode(struct dwc3_meson_g12a *priv,
+ bool is_peripheral)
+{
+ if (is_peripheral) {
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R0,
+ USB_R0_U2D_ACT, USB_R0_U2D_ACT);
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R0,
+ USB_R0_U2D_SS_SCALEDOWN_MODE_MASK, 0);
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R4,
+ USB_R4_P21_SLEEP_M0, USB_R4_P21_SLEEP_M0);
+ } else {
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R0,
+ USB_R0_U2D_ACT, 0);
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R4,
+ USB_R4_P21_SLEEP_M0, 0);
+ }
+}
+
+static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv)
+{
+ int ret;
+
+ ret = dwc3_meson_g12a_usb2_init(priv);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R1,
+ USB_R1_U3H_FLADJ_30MHZ_REG_MASK,
+ FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20));
+
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R5,
+ USB_R5_ID_DIG_EN_0,
+ USB_R5_ID_DIG_EN_0);
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R5,
+ USB_R5_ID_DIG_EN_1,
+ USB_R5_ID_DIG_EN_1);
+ regmap_update_bits(priv->regmap, USB_REG_OFFSET + USB_R5,
+ USB_R5_ID_DIG_TH_MASK,
+ FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff));
+
+ /* If we have an actual SuperSpeed port, initialize it */
+ if (priv->usb3_ports)
+ dwc3_meson_g12a_usb3_init(priv);
+
+ dwc3_meson_g12a_usb_init_mode(priv,
+ (priv->otg_phy_mode == PHY_MODE_USB_DEVICE));
+
+ return 0;
+}
+
+static const struct regmap_config phy_meson_g12a_usb3_regmap_conf = {
+ .reg_bits = 8,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = USB_REG_OFFSET + USB_R5,
+};
+
+static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv)
+{
+ struct device_node *port, *phy_node;
+ struct of_phandle_args args;
+ enum usb_dr_mode mode;
+ const char *dr_mode;
+ struct phy *phy;
+ int ret, i;
+
+ for (i = 0 ; i < MAX_PHY ; ++i) {
+ port = of_graph_get_port_by_id(priv->dev->of_node, i);
+
+ /* Ignore port if not defined or disabled */
+ if (!of_device_is_available(port)) {
+ of_node_put(port);
+ continue;
+ }
+
+ /* Get associated PHY */
+ phy = of_phy_get(port, NULL);
+ if (IS_ERR(phy)) {
+ of_node_put(port);
+ ret = PTR_ERR(phy);
+ goto err_phy_get;
+ }
+
+ of_node_put(port);
+
+ /* Get phy dr_mode */
+ ret = of_parse_phandle_with_args(port, "phys", "#phy-cells",
+ 0, &args);
+ if (ret) {
+ of_node_put(port);
+ goto err_phy_get;
+ }
+
+ phy_node = args.np;
+
+ ret = of_property_read_string(phy_node, "dr_mode", &dr_mode);
+ if (ret) {
+ dr_mode = "unknown";
+ mode = USB_DR_MODE_UNKNOWN;
+ } else {
+ if (!strcmp(dr_mode, "host"))
+ mode = USB_DR_MODE_HOST;
+ else if (!strcmp(dr_mode, "otg"))
+ mode = USB_DR_MODE_OTG;
+ else if (!strcmp(dr_mode, "peripheral"))
+ mode = USB_DR_MODE_PERIPHERAL;
+ else {
+ mode = USB_DR_MODE_UNKNOWN;
+ dr_mode = "unknown";
+ }
+ }
+
+ dev_info(priv->dev, "port%d: %s mode %s\n",
+ i, of_node_full_name(phy_node), dr_mode);
+
+ of_node_put(phy_node);
+
+ priv->phy_modes[i] = mode;
+ priv->phys[i] = phy;
+
+ if (i == USB3_PHY)
+ priv->usb3_ports++;
+ else
+ priv->usb2_ports++;
+ }
+
+ dev_info(priv->dev, "usb2 ports: %d\n", priv->usb2_ports);
+ dev_info(priv->dev, "usb3 ports: %d\n", priv->usb3_ports);
+
+ return 0;
+
+err_phy_get:
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_put(priv->phys[i]);
+
+ return ret;
+}
+
+static int dwc3_meson_g12a_mode_force_get(void *data, u64 *val)
+{
+ struct dwc3_meson_g12a *priv = data;
+
+ if (priv->otg_phy_mode == PHY_MODE_USB_HOST)
+ *val = 1;
+ else if (priv->otg_phy_mode == PHY_MODE_USB_DEVICE)
+ *val = 0;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
+static int dwc3_meson_g12a_mode_force_set(void *data, u64 val)
+{
+ struct dwc3_meson_g12a *priv = data;
+ int i;
+
+ if ((val && priv->otg_phy_mode == PHY_MODE_USB_HOST) ||
+ (!val && priv->otg_phy_mode == PHY_MODE_USB_DEVICE))
+ return 0;
+
+ for (i = 0 ; i < USB2_MAX_PHY ; ++i) {
+ if (!priv->phys[i])
+ continue;
+
+ if (priv->phy_modes[i] != USB_DR_MODE_OTG)
+ continue;
+
+ if (val) {
+ dev_info(priv->dev, "switching to Host Mode\n");
+
+ dwc3_meson_g12a_usb2_set_mode(priv, i,
+ USB_DR_MODE_HOST);
+
+ dwc3_meson_g12a_usb_init_mode(priv, false);
+
+ priv->otg_phy_mode = PHY_MODE_USB_HOST;
+ } else {
+ dev_info(priv->dev, "switching to Device Mode\n");
+
+ dwc3_meson_g12a_usb2_set_mode(priv, i,
+ USB_DR_MODE_PERIPHERAL);
+
+ dwc3_meson_g12a_usb_init_mode(priv, true);
+
+ priv->otg_phy_mode = PHY_MODE_USB_DEVICE;
+ }
+
+ return phy_set_mode(priv->phys[i], priv->otg_phy_mode);
+ }
+
+ return -EINVAL;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(dwc3_meson_g12a_mode_force_fops,
+ dwc3_meson_g12a_mode_force_get,
+ dwc3_meson_g12a_mode_force_set, "%llu\n");
+
+static int dwc3_meson_g12a_otg_id_get(void *data, u64 *val)
+{
+ struct dwc3_meson_g12a *priv = data;
+ u32 reg;
+
+ regmap_read(priv->regmap, USB_R5, ®);
+
+ *val = (reg & USB_R5_ID_DIG_CURR);
+
+ return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(dwc3_meson_g12a_otg_id_fops,
+ dwc3_meson_g12a_otg_id_get, NULL, "%llu\n");
+
+/* We provide a DebugFS interface to get the ID value and force OTG switch */
+static int dwc3_meson_g12a_debugfs_init(struct dwc3_meson_g12a *priv)
+{
+ priv->root = debugfs_create_dir("dwc3-meson-g12a", NULL);
+ if (IS_ERR(priv->root))
+ return PTR_ERR(priv->root);
+
+ debugfs_create_file("mode_force", 0600, priv->root, priv,
+ &dwc3_meson_g12a_mode_force_fops);
+
+ debugfs_create_file("otg_id", 0400, priv->root, priv,
+ &dwc3_meson_g12a_otg_id_fops);
+
+ return 0;
+}
+
+static int dwc3_meson_g12a_probe(struct platform_device *pdev)
+{
+ struct dwc3_meson_g12a *priv;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ void __iomem *base;
+ struct resource *res;
+ int ret, i;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ priv->regmap = devm_regmap_init_mmio(dev, base,
+ &phy_meson_g12a_usb3_regmap_conf);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ priv->clk = devm_clk_get(dev, "usb");
+ if (IS_ERR(priv->clk))
+ return PTR_ERR(priv->clk);
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, priv);
+ priv->dev = dev;
+
+ priv->reset = devm_reset_control_get(dev, "usb");
+ if (IS_ERR(priv->reset)) {
+ ret = PTR_ERR(priv->reset);
+ dev_err(dev, "failed to get device reset, err=%d\n", ret);
+ return ret;
+ }
+
+ ret = reset_control_reset(priv->reset);
+ if (ret)
+ return ret;
+
+ ret = dwc3_meson_g12a_get_phys(priv);
+ if (ret)
+ return ret;
+
+ dwc3_meson_g12a_usb_init(priv);
+
+ /* Init PHYs */
+ for (i = 0 ; i < MAX_PHY ; ++i) {
+ if (priv->phys[i]) {
+ ret = phy_init(priv->phys[i]);
+ if (ret)
+ goto err_phys_put;
+ }
+ }
+
+ /* Set OTG PHY mode */
+ for (i = 0 ; i < MAX_PHY ; ++i) {
+ if (priv->phys[i] && priv->phy_modes[i] == USB_DR_MODE_OTG) {
+ ret = phy_set_mode(priv->phys[i], priv->otg_phy_mode);
+ if (ret)
+ goto err_phys_put;
+ }
+ }
+
+ ret = of_platform_populate(np, NULL, NULL, dev);
+ if (ret) {
+ clk_disable_unprepare(priv->clk);
+ clk_put(priv->clk);
+
+ goto err_phys_exit;
+ }
+
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ pm_runtime_get_sync(dev);
+
+ if (dwc3_meson_g12a_debugfs_init(priv))
+ dev_dbg(dev, "Failed to add DebugFS interface\n");
+
+ return 0;
+
+err_phys_exit:
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_exit(priv->phys[i]);
+
+err_phys_put:
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_put(priv->phys[i]);
+
+ return ret;
+}
+
+static int dwc3_meson_g12a_remove(struct platform_device *pdev)
+{
+ struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
+ struct device *dev = &pdev->dev;
+ int i;
+
+ debugfs_remove_recursive(priv->root);
+
+ of_platform_depopulate(dev);
+
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_exit(priv->phys[i]);
+
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_put(priv->phys[i]);
+
+ clk_disable_unprepare(priv->clk);
+ clk_put(priv->clk);
+
+ pm_runtime_disable(dev);
+ pm_runtime_put_noidle(dev);
+ pm_runtime_set_suspended(dev);
+
+ return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
+{
+ struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+
+ clk_disable(priv->clk);
+
+ return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
+{
+ struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+
+ return clk_enable(priv->clk);
+}
+
+static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
+{
+ struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+ int i;
+
+ for (i = 0 ; i < MAX_PHY ; ++i)
+ if (priv->phys[i])
+ phy_exit(priv->phys[i]);
+
+ reset_control_assert(priv->reset);
+
+ return 0;
+}
+
+static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
+{
+ struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
+ int i, ret;
+
+ reset_control_deassert(priv->reset);
+
+ dwc3_meson_g12a_usb_init(priv);
+
+ /* Init PHYs */
+ for (i = 0 ; i < MAX_PHY ; ++i) {
+ if (priv->phys[i]) {
+ ret = phy_init(priv->phys[i]);
+ if (ret)
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
+ SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
+ dwc3_meson_g12a_runtime_resume, NULL)
+};
+
+static const struct of_device_id dwc3_meson_g12a_match[] = {
+ { .compatible = "amlogic,meson-g12a-usb-ctrl" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
+
+static struct platform_driver dwc3_meson_g12a_driver = {
+ .probe = dwc3_meson_g12a_probe,
+ .remove = dwc3_meson_g12a_remove,
+ .driver = {
+ .name = "dwc3-meson-g12a",
+ .of_match_table = dwc3_meson_g12a_match,
+ .pm = &dwc3_meson_g12a_dev_pm_ops,
+ },
+};
+
+module_platform_driver(dwc3_meson_g12a_driver);
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
+MODULE_AUTHOR("Neil Armstrong <narmstrong@xxxxxxxxxxxx>");
--
2.20.1
