USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)
After some experiments, I found that disabling LPM can workaround the
issue.
On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().
Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.
Fixes: de68bab4fa96 ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
---
drivers/usb/core/driver.c | 11 ++++++++---
drivers/usb/core/hub.c | 12 ++++--------
drivers/usb/core/message.c | 3 +--
3 files changed, 13 insertions(+), 13 deletions(-)
diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
index c276ffc5561f..8987cec9549d 100644
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -1901,9 +1901,6 @@ static int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
int ret = -EPERM;
- if (enable && !udev->usb2_hw_lpm_allowed)
- return 0;
-
if (hcd->driver->set_usb2_hw_lpm) {
ret = hcd->driver->set_usb2_hw_lpm(hcd, udev, enable);
if (!ret)
@@ -1915,11 +1912,19 @@ static int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
int usb_enable_usb2_hardware_lpm(struct usb_device *udev)
{
+ if (!udev->usb2_hw_lpm_capable ||
+ !udev->usb2_hw_lpm_allowed ||
+ udev->usb2_hw_lpm_enabled)
+ return 0;
+
return usb_set_usb2_hardware_lpm(udev, 1);
}
int usb_disable_usb2_hardware_lpm(struct usb_device *udev)
{
+ if (!udev->usb2_hw_lpm_enabled)
+ return 0;
+
return usb_set_usb2_hardware_lpm(udev, 0);
}
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index ca38ff8124a7..55c87be5764c 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -3220,8 +3220,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
}
/* disable USB2 hardware LPM */
- if (udev->usb2_hw_lpm_enabled == 1)
- usb_disable_usb2_hardware_lpm(udev);
+ usb_disable_usb2_hardware_lpm(udev);
if (usb_disable_ltm(udev)) {
dev_err(&udev->dev, "Failed to disable LTM before suspend\n");
@@ -3259,8 +3258,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
usb_enable_ltm(udev);
err_ltm:
/* Try to enable USB2 hardware LPM again */
- if (udev->usb2_hw_lpm_capable == 1)
- usb_enable_usb2_hardware_lpm(udev);
+ usb_enable_usb2_hardware_lpm(udev);
if (udev->do_remote_wakeup)
(void) usb_disable_remote_wakeup(udev);
@@ -3543,8 +3541,7 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
hub_port_logical_disconnect(hub, port1);
} else {
/* Try to enable USB2 hardware LPM */
- if (udev->usb2_hw_lpm_capable == 1)
- usb_enable_usb2_hardware_lpm(udev);
+ usb_enable_usb2_hardware_lpm(udev);
/* Try to enable USB3 LTM */
usb_enable_ltm(udev);
@@ -5649,8 +5646,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev)
/* Disable USB2 hardware LPM.
* It will be re-enabled by the enumeration process.
*/
- if (udev->usb2_hw_lpm_enabled == 1)
- usb_disable_usb2_hardware_lpm(udev);
+ usb_disable_usb2_hardware_lpm(udev);
/* Disable LPM while we reset the device and reinstall the alt settings.
* Device-initiated LPM, and system exit latency settings are cleared
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index 35951aea7f50..4f33eb632a88 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -1243,8 +1243,7 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0)
dev->actconfig->interface[i] = NULL;
}
- if (dev->usb2_hw_lpm_enabled == 1)
- usb_disable_usb2_hardware_lpm(dev);
+ usb_disable_usb2_hardware_lpm(dev);
usb_unlocked_disable_lpm(dev);
usb_disable_ltm(dev);
--
2.17.1
