Hi Minas,
On Wed, 19 Dec 2018 14:09:01 +0000
Minas Harutyunyan <minas.harutyunyan@xxxxxxxxxxxx> wrote:
> On 12/18/2018 6:35 PM, John Keeping wrote:
> > Hi Minas,
> >
> > On Fri, 14 Dec 2018 09:00:08 +0000
> > Minas Harutyunyan <minas.harutyunyan@xxxxxxxxxxxx> wrote:
> >> First of all, sorry for delayed answer.
> >> Looks like similar issue seen by Andrzej Pietrasiewicz
> >> <andrzej.p@xxxxxxxxxxx>: "dwc2 isochronous transfers issues". Same
> >> feedback provided to Andrzej.
> >>
> >> I run tests on 4.20.0-rc4 in DDMA. By default IN ISOC traffic
> >> failed because of BNA interrupts. It's happen because UAC2
> >> requests count set by default to 2. Our core and driver can't work
> >> in DDMA with descriptor list length equal to 2. It's not possible
> >> on time prepare next descriptors to avoid BNA interrupt.
> >>
> >> By changing UAC2_DEF_REQ_NUM to 4 all audio gadget tests passed
> >> smoothly. Could you please apply this patch and run tests in DDMA
> >> mode:
> >>
> >> diff --git a/drivers/usb/gadget/function/u_uac2.h
> >> b/drivers/usb/gadget/function/u_uac2.h
> >> index 8362ee572e1e..5e649259ab76 100644
> >> --- a/drivers/usb/gadget/function/u_uac2.h
> >> +++ b/drivers/usb/gadget/function/u_uac2.h
> >> @@ -21,7 +21,7 @@
> >> #define UAC2_DEF_CCHMASK 0x3
> >> #define UAC2_DEF_CSRATE 64000
> >> #define UAC2_DEF_CSSIZE 2
> >> -#define UAC2_DEF_REQ_NUM 2
> >> +#define UAC2_DEF_REQ_NUM 4
> >>
> >> struct f_uac2_opts {
> >> struct usb_function_instance func_inst;
> >>
> >>
> >> If it will OK on your side also then will switch to BDMA mode and
> >> debug.
> >
> > With DDMA enabled, I see the following error after the stream has
> > been running for a while (anything from a few seconds to a few
> > minutes):
> > -- >8 --
> > [ 1798.836322] dwc2 ff580000.usb: dwc2_hsotg_ep_disable: called for
> > ep0 [ 1798.836329] dwc2 ff580000.usb: dwc2_hsotg_ep_disable: called
> > for ep0 [ 1798.851092] dwc2 ff580000.usb: new device is high-speed
> > [ 1798.924461] dwc2 ff580000.usb: new device is high-speed
> > [ 1798.982887] dwc2 ff580000.usb: new address 25
> > [ 1799.002463] configfs-gadget gadget: high-speed config #1: config
> > -- 8< --
> >
> > On the host side (Linux 4.18.16 Intel xHCI), I see this logged at
> > the same time:
> >
> > -- >8 --
> > [1735740.716242] retire_capture_urb: usb 1-2.2.7: frame 0 active:
> > -71 [1735740.716990] retire_capture_urb: usb 1-2.2.7: frame 0
> > active: -71 [1735740.717906] retire_capture_urb: usb 1-2.2.7: frame
> > 0 active: -71 [1735740.718905] retire_capture_urb: usb 1-2.2.7:
> > frame 0 active: -71 [1735740.719916] retire_capture_urb: usb
> > 1-2.2.7: frame 0 active: -71 [1735740.720032] usb 1-2.2-port7:
> > disabled by hub (EMI?), re-enabling... [1735740.720036] usb
> > 1-2.2.7: USB disconnect, device number 28 [1735740.937500] usb
> > 1-2.2.7: new high-speed USB device number 29 using xhci_hcd -- 8< --
> >
> > The device does then enumerate and works for a period of time
> > before the same error happens again.
> >
> From logs not clear who initiate disconnect: host or device. More
> probably host, after some errors in retire_capture_urb initiate
> disconnect. Do you have any idea?
> Can't you connect device to host on same platform?
> If root cause of disconnect by host is device issue, i.e. not able to
> send to host data packets in time then I need device side dmesg log
> with debug enabled. USB trace around the disconnect will help to
> debug.
I remember running a test with a hardware USB analyzer and which showed
an isochronous packet with an incorrect length (much larger than it
should have been) when the failure occurred.
I don't have any logs from that test and I'm out of the office at the
moment, but I will capture logs when I'm back in January.
Thanks,
John
