Quoting Jorge Ramirez-Ortiz (2018-12-07 01:55:58)
> From: Shawn Guo <shawn.guo@xxxxxxxxxx>
>
> Driver to control the Synopsys SS PHY 1.0.0 implemeneted in QCS404
>
> Based on Sriharsha Allenki's <sallenki@xxxxxxxxxxxxxx> original code.
>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@xxxxxxxxxx>
> Signed-off-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
chain should be swapped?
> Reviewed-by: Vinod Koul <vkoul@xxxxxxxxxx>
> ---
> diff --git a/drivers/phy/qualcomm/phy-qcom-usb-ss.c b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
> new file mode 100644
> index 0000000..7b6a55e
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-usb-ss.c
> +
> +struct ssphy_priv {
> + void __iomem *base;
> + struct device *dev;
> + struct reset_control *reset_com;
> + struct reset_control *reset_phy;
> + struct clk *clk_ref;
> + struct clk *clk_phy;
> + struct clk *clk_pipe;
Use bulk clk APIs? And just get and enable all the clks?
> + struct regulator *vdda1p8;
> + struct regulator *vbus;
> + struct regulator *vdd;
> + unsigned int vdd_levels[LEVEL_NUM];
> +};
> +
> +static inline void qcom_ssphy_updatel(void __iomem *addr, u32 mask, u32 val)
> +{
> + writel((readl(addr) & ~mask) | val, addr);
> +}
> +
> +static int qcom_ssphy_config_vdd(struct ssphy_priv *priv,
> + enum phy_vdd_level level)
> +{
> + return regulator_set_voltage(priv->vdd,
> + priv->vdd_levels[level],
> + priv->vdd_levels[LEVEL_MAX]);
regulator_set_voltage(reg, 0, max) is very suspicious. It's voltage
corners where the voltages are known?
> +}
> +
> +static int qcom_ssphy_ldo_enable(struct ssphy_priv *priv)
> +{
> + int ret;
> +
> + ret = regulator_set_load(priv->vdda1p8, 23000);
Do you need to do this? Why can't the regulator be in high power mode
all the time and then go low power when it's disabled?
> + if (ret < 0) {
> + dev_err(priv->dev, "Failed to set regulator1p8 load\n");
> + return ret;
> + }
> +
> + ret = regulator_set_voltage(priv->vdda1p8, 1800000, 1800000);
This looks unnecessary. The 1.8V regulator sounds like it better be 1.8V
so board constraints should enforce that. All that should be here is
enabling the regulator.
> + if (ret) {
> + dev_err(priv->dev, "Failed to set regulator1p8 voltage\n");
> + goto put_vdda1p8_lpm;
> + }
> +
> + ret = regulator_enable(priv->vdda1p8);
> + if (ret) {
> + dev_err(priv->dev, "Failed to enable regulator1p8\n");
> + goto unset_vdda1p8;
> + }
> +
> + return ret;
> +
> + /* rollback regulator changes */
> +
> +unset_vdda1p8:
> + regulator_set_voltage(priv->vdda1p8, 0, 1800000);
> +
> +put_vdda1p8_lpm:
> + regulator_set_load(priv->vdda1p8, 0);
> +
> + return ret;
> +}
> +
> +static void qcom_ssphy_ldo_disable(struct ssphy_priv *priv)
> +{
> + regulator_disable(priv->vdda1p8);
> + regulator_set_voltage(priv->vdda1p8, 0, 1800000);
Urgh why?
> + regulator_set_load(priv->vdda1p8, 0);
> +}
