USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx>
---
drivers/usb/host/xhci-hub.c | 60 ++++++++++++++++++++++++++++++++++-----------
1 file changed, 46 insertions(+), 14 deletions(-)
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index da98a11..94aca1b 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -1474,15 +1474,18 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
unsigned long flags;
struct xhci_hub *rhub;
struct xhci_port **ports;
+ u32 portsc_buf[USB_MAXCHILDREN];
+ bool wake_enabled;
rhub = xhci_get_rhub(hcd);
ports = rhub->ports;
max_ports = rhub->num_ports;
bus_state = &xhci->bus_state[hcd_index(hcd)];
+ wake_enabled = hcd->self.root_hub->do_remote_wakeup;
spin_lock_irqsave(&xhci->lock, flags);
- if (hcd->self.root_hub->do_remote_wakeup) {
+ if (wake_enabled) {
if (bus_state->resuming_ports || /* USB2 */
bus_state->port_remote_wakeup) { /* USB3 */
spin_unlock_irqrestore(&xhci->lock, flags);
@@ -1490,26 +1493,36 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
return -EBUSY;
}
}
-
- port_index = max_ports;
+ /*
+ * Prepare ports for suspend, but don't write anything before all ports
+ * are checked and we know bus suspend can proceed
+ */
bus_state->bus_suspended = 0;
+ port_index = max_ports;
while (port_index--) {
- /* suspend the port if the port is not suspended */
u32 t1, t2;
- int slot_id;
t1 = readl(ports[port_index]->addr);
t2 = xhci_port_state_to_neutral(t1);
+ portsc_buf[port_index] = 0;
- if ((t1 & PORT_PE) && !(t1 & PORT_PLS_MASK)) {
- xhci_dbg(xhci, "port %d not suspended\n", port_index);
- slot_id = xhci_find_slot_id_by_port(hcd, xhci,
- port_index + 1);
- if (slot_id) {
+ /* Bail out if a USB3 port has a new device in link training */
+ if ((t1 & PORT_PLS_MASK) == XDEV_POLLING) {
+ bus_state->bus_suspended = 0;
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ xhci_dbg(xhci, "Bus suspend bailout, port in polling\n");
+ return -EBUSY;
+ }
+
+ /* suspend ports in U0, or bail out for new connect changes */
+ if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) {
+ if ((t1 & PORT_CSC) && wake_enabled) {
+ bus_state->bus_suspended = 0;
spin_unlock_irqrestore(&xhci->lock, flags);
- xhci_stop_device(xhci, slot_id, 1);
- spin_lock_irqsave(&xhci->lock, flags);
+ xhci_dbg(xhci, "Bus suspend bailout, port connect change\n");
+ return -EBUSY;
}
+ xhci_dbg(xhci, "port %d not suspended\n", port_index);
t2 &= ~PORT_PLS_MASK;
t2 |= PORT_LINK_STROBE | XDEV_U3;
set_bit(port_index, &bus_state->bus_suspended);
@@ -1518,7 +1531,7 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
* including the USB 3.0 roothub, but only if CONFIG_PM
* is enabled, so also enable remote wake here.
*/
- if (hcd->self.root_hub->do_remote_wakeup) {
+ if (wake_enabled) {
if (t1 & PORT_CONNECT) {
t2 |= PORT_WKOC_E | PORT_WKDISC_E;
t2 &= ~PORT_WKCONN_E;
@@ -1538,7 +1551,26 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
t1 = xhci_port_state_to_neutral(t1);
if (t1 != t2)
- writel(t2, ports[port_index]->addr);
+ portsc_buf[port_index] = t2;
+ }
+
+ /* write port settings, stopping and suspending ports if needed */
+ port_index = max_ports;
+ while (port_index--) {
+ if (!portsc_buf[port_index])
+ continue;
+ if (test_bit(port_index, &bus_state->bus_suspended)) {
+ int slot_id;
+
+ slot_id = xhci_find_slot_id_by_port(hcd, xhci,
+ port_index + 1);
+ if (slot_id) {
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ xhci_stop_device(xhci, slot_id, 1);
+ spin_lock_irqsave(&xhci->lock, flags);
+ }
+ }
+ writel(portsc_buf[port_index], ports[port_index]->addr);
}
hcd->state = HC_STATE_SUSPENDED;
bus_state->next_statechange = jiffies + msecs_to_jiffies(10);
--
2.7.4
