The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
+00h: to indicate the section is valid
+01h~04h: UART Mode & port availability
+05h~08h: Output pin control on IC power on
+09h~12h: Output pin control on working <-- New added
Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.
This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@xxxxxxxxx>
---
drivers/usb/serial/f81534.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 380933db34dd..2b39bda035c7 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -45,14 +45,17 @@
#define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS)
#define F81534_DEF_CONF_ADDRESS_START 0x3000
-#define F81534_DEF_CONF_SIZE 8
+#define F81534_DEF_CONF_SIZE 12
#define F81534_CUSTOM_ADDRESS_START 0x2f00
#define F81534_CUSTOM_DATA_SIZE 0x10
#define F81534_CUSTOM_NO_CUSTOM_DATA 0xff
#define F81534_CUSTOM_VALID_TOKEN 0xf0
#define F81534_CONF_OFFSET 1
-#define F81534_CONF_GPIO_OFFSET 4
+#define F81534_CONF_INIT_GPIO_OFFSET 4
+#define F81534_CONF_WORK_GPIO_OFFSET 8
+#define F81534_CONF_GPIO_SHUTDOWN 7
+#define F81534_CONF_GPIO_RS232 1
#define F81534_MAX_DATA_BLOCK 64
#define F81534_MAX_BUS_RETRY 20
@@ -1337,8 +1340,19 @@ static int f81534_set_port_output_pin(struct usb_serial_port *port)
serial_priv = usb_get_serial_data(serial);
port_priv = usb_get_serial_port_data(port);
- idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num;
+ idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num;
value = serial_priv->conf_data[idx];
+ if (value >= F81534_CONF_GPIO_SHUTDOWN) {
+ /*
+ * Newer IC configure will make transceiver in shutdown mode on
+ * initial power on. We need enable it before using UARTs.
+ */
+ idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num;
+ value = serial_priv->conf_data[idx];
+ if (value >= F81534_CONF_GPIO_SHUTDOWN)
+ value = F81534_CONF_GPIO_RS232;
+ }
+
pins = &f81534_port_out_pins[port_priv->phy_num];
for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {
--
2.7.4
