Add the build system changes needed to get the Broadcom STB XHCI, EHCI and OHCI functionality working. The link order for XHCI was changed in the Makefile because of the way STB XHCI, EHCI and OHCI controllers share a port which requires that the XHCI driver be initialized first. Also update MAINTAINERS. Signed-off-by: Al Cooper <alcooperx@xxxxxxxxx> --- MAINTAINERS | 9 +++++++++ arch/arm/configs/multi_v7_defconfig | 1 + arch/arm64/configs/defconfig | 1 + drivers/usb/host/Kconfig | 26 ++++++++++++++++++++++++++ drivers/usb/host/Makefile | 18 ++++++++++++------ 5 files changed, 49 insertions(+), 6 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 2f3eba4484aa..932fcc6f8ff5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2998,6 +2998,15 @@ S: Supported F: drivers/i2c/busses/i2c-brcmstb.c F: Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt +BROADCOM BRCMSTB USB XHCI, EHCI and OHCI DRIVERS +M: Al Cooper <alcooperx@xxxxxxxxx> +L: linux-usb@xxxxxxxxxxxxxxx +L: bcm-kernel-feedback-list@xxxxxxxxxxxx +S: Maintained +F: drivers/usb/host/ehci-brcm.* +F: drivers/usb/host/xhci-brcm.* +F: Documentation/devicetree/bindings/usb/brcm,bcm7445-*.txt + BROADCOM BRCMSTB USB2 and USB3 PHY DRIVER M: Al Cooper <alcooperx@xxxxxxxxx> L: linux-kernel@xxxxxxxxxxxxxxx diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 63af6234c1b6..64ca0edb43ed 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -726,6 +726,7 @@ CONFIG_USB_CHIPIDEA_UDC=y CONFIG_USB_CHIPIDEA_HOST=y CONFIG_USB_ISP1760=y CONFIG_USB_HSIC_USB3503=y +CONFIG_USB_BRCM=y CONFIG_AB8500_USB=y CONFIG_KEYSTONE_USB_PHY=m CONFIG_NOP_USB_XCEIV=m diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index c9a57d11330b..89637256e7bf 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -520,6 +520,7 @@ CONFIG_USB_GADGET=y CONFIG_USB_RENESAS_USBHS_UDC=m CONFIG_USB_RENESAS_USB3=m CONFIG_USB_ULPI_BUS=y +CONFIG_USB_BRCM=y CONFIG_MMC=y CONFIG_MMC_BLOCK_MINORS=32 CONFIG_MMC_ARMMMCI=y diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 16758b12a5e9..2d0b3060ad05 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -96,6 +96,32 @@ config USB_XHCI_TEGRA endif # USB_XHCI_HCD +config USB_OHCI_BRCM + tristate + +config USB_EHCI_BRCM + tristate + +config USB_XHCI_BRCM + tristate + +config BRCM_USB_PHY + tristate + +config USB_BRCM + tristate "Broadcom STB USB support" + depends on ARCH_BRCMSTB || COMPILE_TEST + select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD + select USB_EHCI_BRCM if USB_EHCI_HCD + select USB_XHCI_BRCM if USB_XHCI_HCD + select USB_XHCI_PLATFORM if USB_XHCI_HCD + help + Say Y to enable support for XHCI, EHCI and OHCI host controllers + found in Broadcom STB SoC's. + + Disabling this will keep the controllers and corresponding + PHYs powered down. + config USB_EHCI_HCD tristate "EHCI HCD (USB 2.0) support" depends on HAS_DMA && HAS_IOMEM diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 84514f71ae44..9bdd64b710ee 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -31,6 +31,10 @@ ifneq ($(CONFIG_USB_XHCI_RCAR), ) xhci-plat-hcd-y += xhci-rcar.o endif +ifneq ($(CONFIG_USB_XHCI_BRCM), ) + xhci-plat-hcd-y += xhci-brcm.o +endif + ifneq ($(CONFIG_DEBUG_FS),) xhci-hcd-y += xhci-debugfs.o endif @@ -39,6 +43,13 @@ obj-$(CONFIG_USB_WHCI_HCD) += whci/ obj-$(CONFIG_USB_PCI) += pci-quirks.o +obj-$(CONFIG_USB_XHCI_HCD) += xhci-hcd.o +obj-$(CONFIG_USB_XHCI_PCI) += xhci-pci.o +obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o +obj-$(CONFIG_USB_XHCI_HISTB) += xhci-histb.o +obj-$(CONFIG_USB_XHCI_MTK) += xhci-mtk.o +obj-$(CONFIG_USB_XHCI_TEGRA) += xhci-tegra.o + obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o obj-$(CONFIG_USB_EHCI_HCD_PLATFORM) += ehci-platform.o @@ -52,6 +63,7 @@ obj-$(CONFIG_USB_EHCI_EXYNOS) += ehci-exynos.o obj-$(CONFIG_USB_EHCI_HCD_AT91) += ehci-atmel.o obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o obj-$(CONFIG_USB_W90X900_EHCI) += ehci-w90x900.o +obj-$(CONFIG_USB_EHCI_BRCM) += ehci-brcm.o obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o @@ -72,12 +84,6 @@ obj-$(CONFIG_USB_OHCI_HCD_DAVINCI) += ohci-da8xx.o obj-$(CONFIG_USB_UHCI_HCD) += uhci-hcd.o obj-$(CONFIG_USB_FHCI_HCD) += fhci.o -obj-$(CONFIG_USB_XHCI_HCD) += xhci-hcd.o -obj-$(CONFIG_USB_XHCI_PCI) += xhci-pci.o -obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o -obj-$(CONFIG_USB_XHCI_HISTB) += xhci-histb.o -obj-$(CONFIG_USB_XHCI_MTK) += xhci-mtk.o -obj-$(CONFIG_USB_XHCI_TEGRA) += xhci-tegra.o obj-$(CONFIG_USB_SL811_HCD) += sl811-hcd.o obj-$(CONFIG_USB_SL811_CS) += sl811_cs.o obj-$(CONFIG_USB_U132_HCD) += u132-hcd.o -- 1.9.0.138.g2de3478
