On Tue, 2018-09-25 at 10:53 +0530, Kishon Vijay Abraham I wrote:
>
> On Thursday 23 August 2018 02:12 AM, Lubomir Rintel wrote:
> > Turned from arch/arm/mach-mmp/devices.c into a proper PHY driver,
> > so
> > that in can be instantiated from a DT.
> >
> > Signed-off-by: Lubomir Rintel <lkundrak@xxxxx>
>
> Acked-by: Kishon Vijay Abraham I <kishon@xxxxxx>
>
> If this has to be merged via linux-phy tree, please let me know.
Yes, either linux-phy or the usb tree.
The EHCI patches have already been pulled into the usb tree, presumably
because they got an Ack from Alan Stern. That includes "USB: EHCI:
ehci-mv: use phy-pxa-usb" that depends on this. Perhaps the rest of
the patches can go via the same tree?
I haven't submitted a patchset that would have dependencies spanning
across different subsystems before. I don't know what's usually done in
such cases. Advice welcome.
Greg?
> Thanks
> Kishon
Thank you
Lubo
>
> > ---
> > drivers/phy/marvell/Kconfig | 11 +
> > drivers/phy/marvell/Makefile | 1 +
> > drivers/phy/marvell/phy-pxa-usb.c | 345
> > ++++++++++++++++++++++++++++++
> > 3 files changed, 357 insertions(+)
> > create mode 100644 drivers/phy/marvell/phy-pxa-usb.c
> >
> > diff --git a/drivers/phy/marvell/Kconfig
> > b/drivers/phy/marvell/Kconfig
> > index 68e321225400..6fb4b56e4c14 100644
> > --- a/drivers/phy/marvell/Kconfig
> > +++ b/drivers/phy/marvell/Kconfig
> > @@ -59,3 +59,14 @@ config PHY_PXA_28NM_USB2
> > The PHY driver will be used by Marvell udc/ehci/otg driver.
> >
> > To compile this driver as a module, choose M here.
> > +
> > +config PHY_PXA_USB
> > + tristate "Marvell PXA USB PHY Driver"
> > + depends on ARCH_PXA || ARCH_MMP
> > + select GENERIC_PHY
> > + help
> > + Enable this to support Marvell PXA USB PHY driver for Marvell
> > + SoC. This driver will do the PHY initialization and shutdown.
> > + The PHY driver will be used by Marvell udc/ehci/otg driver.
> > +
> > + To compile this driver as a module, choose M here.
> > diff --git a/drivers/phy/marvell/Makefile
> > b/drivers/phy/marvell/Makefile
> > index 5c3ec5d10e0d..3975b144f8ec 100644
> > --- a/drivers/phy/marvell/Makefile
> > +++ b/drivers/phy/marvell/Makefile
> > @@ -6,3 +6,4 @@ obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY) += phy-
> > mvebu-cp110-comphy.o
> > obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
> > obj-$(CONFIG_PHY_PXA_28NM_HSIC) += phy-pxa-28nm-hsic.o
> > obj-$(CONFIG_PHY_PXA_28NM_USB2) += phy-pxa-28nm-usb2.o
> > +obj-$(CONFIG_PHY_PXA_USB) += phy-pxa-usb.o
> > diff --git a/drivers/phy/marvell/phy-pxa-usb.c
> > b/drivers/phy/marvell/phy-pxa-usb.c
> > new file mode 100644
> > index 000000000000..87ff7550b912
> > --- /dev/null
> > +++ b/drivers/phy/marvell/phy-pxa-usb.c
> > @@ -0,0 +1,345 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2011 Marvell International Ltd. All rights
> > reserved.
> > + * Copyright (C) 2018 Lubomir Rintel <lkundrak@xxxxx>
> > + */
> > +
> > +#include <dt-bindings/phy/phy.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +
> > +/* phy regs */
> > +#define UTMI_REVISION 0x0
> > +#define UTMI_CTRL 0x4
> > +#define UTMI_PLL 0x8
> > +#define UTMI_TX 0xc
> > +#define UTMI_RX 0x10
> > +#define UTMI_IVREF 0x14
> > +#define UTMI_T0 0x18
> > +#define UTMI_T1 0x1c
> > +#define UTMI_T2 0x20
> > +#define UTMI_T3 0x24
> > +#define UTMI_T4 0x28
> > +#define UTMI_T5 0x2c
> > +#define UTMI_RESERVE 0x30
> > +#define UTMI_USB_INT 0x34
> > +#define UTMI_DBG_CTL 0x38
> > +#define UTMI_OTG_ADDON 0x3c
> > +
> > +/* For UTMICTRL Register */
> > +#define UTMI_CTRL_USB_CLK_EN (1 << 31)
> > +/* pxa168 */
> > +#define UTMI_CTRL_SUSPEND_SET1 (1 << 30)
> > +#define UTMI_CTRL_SUSPEND_SET2 (1 << 29)
> > +#define UTMI_CTRL_RXBUF_PDWN (1 << 24)
> > +#define UTMI_CTRL_TXBUF_PDWN (1 << 11)
> > +
> > +#define UTMI_CTRL_INPKT_DELAY_SHIFT 30
> > +#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28
> > +#define UTMI_CTRL_PU_REF_SHIFT 20
> > +#define UTMI_CTRL_ARC_PULLDN_SHIFT 12
> > +#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1
> > +#define UTMI_CTRL_PWR_UP_SHIFT 0
> > +
> > +/* For UTMI_PLL Register */
> > +#define UTMI_PLL_PLLCALI12_SHIFT 29
> > +#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29)
> > +
> > +#define UTMI_PLL_PLLVDD18_SHIFT 27
> > +#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27)
> > +
> > +#define UTMI_PLL_PLLVDD12_SHIFT 25
> > +#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25)
> > +
> > +#define UTMI_PLL_CLK_BLK_EN_SHIFT 24
> > +#define CLK_BLK_EN (0x1 << 24)
> > +#define PLL_READY (0x1 << 23)
> > +#define KVCO_EXT (0x1 << 22)
> > +#define VCOCAL_START (0x1 << 21)
> > +
> > +#define UTMI_PLL_KVCO_SHIFT 15
> > +#define UTMI_PLL_KVCO_MASK (0x7 << 15)
> > +
> > +#define UTMI_PLL_ICP_SHIFT 12
> > +#define UTMI_PLL_ICP_MASK (0x7 << 12)
> > +
> > +#define UTMI_PLL_FBDIV_SHIFT 4
> > +#define UTMI_PLL_FBDIV_MASK (0xFF << 4)
> > +
> > +#define UTMI_PLL_REFDIV_SHIFT 0
> > +#define UTMI_PLL_REFDIV_MASK (0xF << 0)
> > +
> > +/* For UTMI_TX Register */
> > +#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27
> > +#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27)
> > +
> > +#define UTMI_TX_REG_EXT_FS_RCAL_EN_SHIFT 26
> > +#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK (0x1 << 26)
> > +
> > +#define UTMI_TX_TXVDD12_SHIFT 22
> > +#define UTMI_TX_TXVDD12_MASK (0x3 << 22)
> > +
> > +#define UTMI_TX_CK60_PHSEL_SHIFT 17
> > +#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17)
> > +
> > +#define UTMI_TX_IMPCAL_VTH_SHIFT 14
> > +#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14)
> > +
> > +#define REG_RCAL_START (0x1 << 12)
> > +
> > +#define UTMI_TX_LOW_VDD_EN_SHIFT 11
> > +
> > +#define UTMI_TX_AMP_SHIFT 0
> > +#define UTMI_TX_AMP_MASK (0x7 << 0)
> > +
> > +/* For UTMI_RX Register */
> > +#define UTMI_REG_SQ_LENGTH_SHIFT 15
> > +#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15)
> > +
> > +#define UTMI_RX_SQ_THRESH_SHIFT 4
> > +#define UTMI_RX_SQ_THRESH_MASK (0xf << 4)
> > +
> > +#define UTMI_OTG_ADDON_OTG_ON (1 << 0)
> > +
> > +enum pxa_usb_phy_version {
> > + PXA_USB_PHY_MMP2,
> > + PXA_USB_PHY_PXA910,
> > + PXA_USB_PHY_PXA168,
> > +};
> > +
> > +struct pxa_usb_phy {
> > + struct phy *phy;
> > + void __iomem *base;
> > + enum pxa_usb_phy_version version;
> > +};
> > +
> > +/*****************************************************************
> > ************
> > + * The registers read/write routines
> > +
> > *******************************************************************
> > **********/
> > +
> > +static unsigned int u2o_get(void __iomem *base, unsigned int
> > offset)
> > +{
> > + return readl_relaxed(base + offset);
> > +}
> > +
> > +static void u2o_set(void __iomem *base, unsigned int offset,
> > + unsigned int value)
> > +{
> > + u32 reg;
> > +
> > + reg = readl_relaxed(base + offset);
> > + reg |= value;
> > + writel_relaxed(reg, base + offset);
> > + readl_relaxed(base + offset);
> > +}
> > +
> > +static void u2o_clear(void __iomem *base, unsigned int offset,
> > + unsigned int value)
> > +{
> > + u32 reg;
> > +
> > + reg = readl_relaxed(base + offset);
> > + reg &= ~value;
> > + writel_relaxed(reg, base + offset);
> > + readl_relaxed(base + offset);
> > +}
> > +
> > +static void u2o_write(void __iomem *base, unsigned int offset,
> > + unsigned int value)
> > +{
> > + writel_relaxed(value, base + offset);
> > + readl_relaxed(base + offset);
> > +}
> > +
> > +static int pxa_usb_phy_init(struct phy *phy)
> > +{
> > + struct pxa_usb_phy *pxa_usb_phy = phy_get_drvdata(phy);
> > + void __iomem *base = pxa_usb_phy->base;
> > + int loops;
> > +
> > + dev_info(&phy->dev, "initializing Marvell PXA USB PHY");
> > +
> > + /* Initialize the USB PHY power */
> > + if (pxa_usb_phy->version == PXA_USB_PHY_PXA910) {
> > + u2o_set(base, UTMI_CTRL,
> > (1<<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT)
> > + | (1<<UTMI_CTRL_PU_REF_SHIFT));
> > + }
> > +
> > + u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
> > + u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
> > +
> > + /* UTMI_PLL settings */
> > + u2o_clear(base, UTMI_PLL, UTMI_PLL_PLLVDD18_MASK
> > + | UTMI_PLL_PLLVDD12_MASK | UTMI_PLL_PLLCALI12_MASK
> > + | UTMI_PLL_FBDIV_MASK | UTMI_PLL_REFDIV_MASK
> > + | UTMI_PLL_ICP_MASK | UTMI_PLL_KVCO_MASK);
> > +
> > + u2o_set(base, UTMI_PLL, 0xee<<UTMI_PLL_FBDIV_SHIFT
> > + | 0xb<<UTMI_PLL_REFDIV_SHIFT |
> > 3<<UTMI_PLL_PLLVDD18_SHIFT
> > + | 3<<UTMI_PLL_PLLVDD12_SHIFT |
> > 3<<UTMI_PLL_PLLCALI12_SHIFT
> > + | 1<<UTMI_PLL_ICP_SHIFT | 3<<UTMI_PLL_KVCO_SHIFT);
> > +
> > + /* UTMI_TX */
> > + u2o_clear(base, UTMI_TX, UTMI_TX_REG_EXT_FS_RCAL_EN_MASK
> > + | UTMI_TX_TXVDD12_MASK | UTMI_TX_CK60_PHSEL_MASK
> > + | UTMI_TX_IMPCAL_VTH_MASK |
> > UTMI_TX_REG_EXT_FS_RCAL_MASK
> > + | UTMI_TX_AMP_MASK);
> > + u2o_set(base, UTMI_TX, 3<<UTMI_TX_TXVDD12_SHIFT
> > + | 4<<UTMI_TX_CK60_PHSEL_SHIFT |
> > 4<<UTMI_TX_IMPCAL_VTH_SHIFT
> > + | 8<<UTMI_TX_REG_EXT_FS_RCAL_SHIFT |
> > 3<<UTMI_TX_AMP_SHIFT);
> > +
> > + /* UTMI_RX */
> > + u2o_clear(base, UTMI_RX, UTMI_RX_SQ_THRESH_MASK
> > + | UTMI_REG_SQ_LENGTH_MASK);
> > + u2o_set(base, UTMI_RX, 7<<UTMI_RX_SQ_THRESH_SHIFT
> > + | 2<<UTMI_REG_SQ_LENGTH_SHIFT);
> > +
> > + /* UTMI_IVREF */
> > + if (pxa_usb_phy->version == PXA_USB_PHY_PXA168) {
> > + /*
> > + * fixing Microsoft Altair board interface with NEC hub
> > issue -
> > + * Set UTMI_IVREF from 0x4a3 to 0x4bf
> > + */
> > + u2o_write(base, UTMI_IVREF, 0x4bf);
> > + }
> > +
> > + /* toggle VCOCAL_START bit of UTMI_PLL */
> > + udelay(200);
> > + u2o_set(base, UTMI_PLL, VCOCAL_START);
> > + udelay(40);
> > + u2o_clear(base, UTMI_PLL, VCOCAL_START);
> > +
> > + /* toggle REG_RCAL_START bit of UTMI_TX */
> > + udelay(400);
> > + u2o_set(base, UTMI_TX, REG_RCAL_START);
> > + udelay(40);
> > + u2o_clear(base, UTMI_TX, REG_RCAL_START);
> > + udelay(400);
> > +
> > + /* Make sure PHY PLL is ready */
> > + loops = 0;
> > + while ((u2o_get(base, UTMI_PLL) & PLL_READY) == 0) {
> > + mdelay(1);
> > + loops++;
> > + if (loops > 100) {
> > + dev_warn(&phy->dev, "calibrate timeout,
> > UTMI_PLL %x\n",
> > + u2o_get(base,
> > UTMI_PLL));
> > + break;
> > + }
> > + }
> > +
> > + if (pxa_usb_phy->version == PXA_USB_PHY_PXA168) {
> > + u2o_set(base, UTMI_RESERVE, 1 << 5);
> > + /* Turn on UTMI PHY OTG extension */
> > + u2o_write(base, UTMI_OTG_ADDON, 1);
> > + }
> > +
> > + return 0;
> > +
> > +}
> > +
> > +static int pxa_usb_phy_exit(struct phy *phy)
> > +{
> > + struct pxa_usb_phy *pxa_usb_phy = phy_get_drvdata(phy);
> > + void __iomem *base = pxa_usb_phy->base;
> > +
> > + dev_info(&phy->dev, "deinitializing Marvell PXA USB PHY");
> > +
> > + if (pxa_usb_phy->version == PXA_USB_PHY_PXA168)
> > + u2o_clear(base, UTMI_OTG_ADDON, UTMI_OTG_ADDON_OTG_ON);
> > +
> > + u2o_clear(base, UTMI_CTRL, UTMI_CTRL_RXBUF_PDWN);
> > + u2o_clear(base, UTMI_CTRL, UTMI_CTRL_TXBUF_PDWN);
> > + u2o_clear(base, UTMI_CTRL, UTMI_CTRL_USB_CLK_EN);
> > + u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
> > + u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct phy_ops pxa_usb_phy_ops = {
> > + .init = pxa_usb_phy_init,
> > + .exit = pxa_usb_phy_exit,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static const struct of_device_id pxa_usb_phy_of_match[] = {
> > + {
> > + .compatible = "marvell,mmp2-usb-phy",
> > + .data = (void *)PXA_USB_PHY_MMP2,
> > + }, {
> > + .compatible = "marvell,pxa910-usb-phy",
> > + .data = (void *)PXA_USB_PHY_PXA910,
> > + }, {
> > + .compatible = "marvell,pxa168-usb-phy",
> > + .data = (void *)PXA_USB_PHY_PXA168,
> > + },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, pxa_usb_phy_of_match);
> > +
> > +static int pxa_usb_phy_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct resource *resource;
> > + struct pxa_usb_phy *pxa_usb_phy;
> > + struct phy_provider *provider;
> > + const struct of_device_id *of_id;
> > +
> > + pxa_usb_phy = devm_kzalloc(dev, sizeof(struct pxa_usb_phy),
> > GFP_KERNEL);
> > + if (!pxa_usb_phy)
> > + return -ENOMEM;
> > +
> > + of_id = of_match_node(pxa_usb_phy_of_match, dev->of_node);
> > + if (of_id)
> > + pxa_usb_phy->version = (enum pxa_usb_phy_version)of_id-
> > >data;
> > + else
> > + pxa_usb_phy->version = PXA_USB_PHY_MMP2;
> > +
> > + resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + pxa_usb_phy->base = devm_ioremap_resource(dev, resource);
> > + if (IS_ERR(pxa_usb_phy->base)) {
> > + dev_err(dev, "failed to remap PHY regs\n");
> > + return PTR_ERR(pxa_usb_phy->base);
> > + }
> > +
> > + pxa_usb_phy->phy = devm_phy_create(dev, NULL,
> > &pxa_usb_phy_ops);
> > + if (IS_ERR(pxa_usb_phy->phy)) {
> > + dev_err(dev, "failed to create PHY\n");
> > + return PTR_ERR(pxa_usb_phy->phy);
> > + }
> > +
> > + phy_set_drvdata(pxa_usb_phy->phy, pxa_usb_phy);
> > + provider = devm_of_phy_provider_register(dev,
> > of_phy_simple_xlate);
> > + if (IS_ERR(provider)) {
> > + dev_err(dev, "failed to register PHY provider\n");
> > + return PTR_ERR(provider);
> > + }
> > +
> > + if (!dev->of_node) {
> > + phy_create_lookup(pxa_usb_phy->phy, "usb", "mv-udc");
> > + phy_create_lookup(pxa_usb_phy->phy, "usb", "pxa-
> > u2oehci");
> > + phy_create_lookup(pxa_usb_phy->phy, "usb", "mv-otg");
> > + }
> > +
> > + dev_info(dev, "Marvell PXA USB PHY");
> > + return 0;
> > +}
> > +
> > +static struct platform_driver pxa_usb_phy_driver = {
> > + .probe = pxa_usb_phy_probe,
> > + .driver = {
> > + .name = "pxa-usb-phy",
> > + .of_match_table = pxa_usb_phy_of_match,
> > + },
> > +};
> > +module_platform_driver(pxa_usb_phy_driver);
> > +
> > +MODULE_AUTHOR("Lubomir Rintel <lkundrak@xxxxx>");
> > +MODULE_DESCRIPTION("Marvell PXA USB PHY Driver");
> > +MODULE_LICENSE("GPL v2");
> >
