Renesas uPD720202 kernel 4.16.13

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

with kernel 4.16.13, at my Lenovo X220, the Renesas uPD720202 card
only works, when inserted at boot time. Taken out and inserted again,
does not work anymore.
smartctl does not work.

Best,
Christian

Part of dmesg:
grep -i xhci 4.16.13-1-ARCH_2018-06-03-08h32m43s
[   19.059181] xhci_hcd 0000:05:00.0: Resetting
[   20.475590] xhci_hcd 0000:05:00.0: xHCI Host Controller
[   20.475605] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 3
[   20.480970] xhci_hcd 0000:05:00.0: hcc params 0x014051cf hci
version 0x100 quirks 0x00000090
[   20.483480] usb usb3: Product: xHCI Host Controller
[   20.483482] usb usb3: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[   20.486997] xhci_hcd 0000:05:00.0: xHCI Host Controller
[   20.487001] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 4
[   20.487006] xhci_hcd 0000:05:00.0: Host supports USB 3.0  SuperSpeed
[   20.487232] usb usb4: Product: xHCI Host Controller
[   20.487234] usb usb4: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[   21.570993] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[   22.467767] usb 4-2: new SuperSpeed USB device number 3 using xhci_hcd
[   38.587716] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[   38.590251] xhci_hcd 0000:05:00.0: @00000004177fe720 00000000
00000000 1b000000 03038001
[  128.532605] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[  128.535123] xhci_hcd 0000:05:00.0: @00000004177fe800 00000000
00000000 1b000000 03038001
[  128.545588] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[  128.546985] xhci_hcd 0000:05:00.0: @00000004177fe910 00000000
00000000 1b000000 03038001
[  128.560955] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[  128.562895] xhci_hcd 0000:05:00.0: @00000004177fe980 00000000
00000000 1b000000 03038001
[  128.573315] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[  128.574273] xhci_hcd 0000:05:00.0: @00000004177fea40 00000000
00000000 1b000000 03038001
[  128.580080] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[  128.581973] xhci_hcd 0000:05:00.0: @00000004177fead0 00000000
00000000 1b000000 03038001
[  824.596691] xhci_hcd 0000:05:00.0: remove, state 1
[  830.314822] xhci_hcd 0000:05:00.0: xHCI host controller not
responding, assume dead
[  830.317056] xhci_hcd 0000:05:00.0: Timeout while waiting for
configure endpoint command
[  830.343621] xhci_hcd 0000:05:00.0: WARN Can't disable streams for
endpoint 0x81, streams are being disabled already
[  830.345391] xhci_hcd 0000:05:00.0: USB bus 4 deregistered
[  830.347624] xhci_hcd 0000:05:00.0: remove, state 4
[  830.352268] xhci_hcd 0000:05:00.0: Host halt failed, -19
[  830.353815] xhci_hcd 0000:05:00.0: Host not accessible, reset failed.
[  830.356083] xhci_hcd 0000:05:00.0: USB bus 3 deregistered
[  830.445157] xhci_hcd 0000:05:00.0: Resetting
[  831.861255] xhci_hcd 0000:05:00.0: xHCI Host Controller
[  831.861908] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 3
[  831.867877] xhci_hcd 0000:05:00.0: hcc params 0x014051cf hci
version 0x100 quirks 0x00000090
[  831.870273] usb usb3: Product: xHCI Host Controller
[  831.870924] usb usb3: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[  831.873946] xhci_hcd 0000:05:00.0: xHCI Host Controller
[  831.874952] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 4
[  831.875972] xhci_hcd 0000:05:00.0: Host supports USB 3.0  SuperSpeed
[  831.879017] usb usb4: Product: xHCI Host Controller
[  831.879730] usb usb4: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[  832.203153] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[  832.746493] xhci_hcd 0000:05:00.0: xHCI host controller not
responding, assume dead
[  832.749124] xhci_hcd 0000:05:00.0: HC died; cleaning up
...
[   38.161387] usbcore: registered new interface driver uvcvideo
[   38.161387] USB Video Class driver (1.1.1)
[   38.172666] usb-storage 4-1:1.0: USB Mass Storage device detected
[   38.173704] scsi host4: usb-storage 4-1:1.0
[   38.265279] usbcore: registered new interface driver usb-storage
[   38.282837] scsi host5: uas
[   38.284088] usbcore: registered new interface driver uas
[   38.284437] scsi 5:0:0:0: Direct-Access     Seagate  M3 Portable
  9300 PQ: 0 ANSI: 6
[   38.288212] sd 5:0:0:0: Attached scsi generic sg2 type 0
[   38.288496] sd 5:0:0:0: [sdc] 7814037167 512-byte logical blocks:
(4.00 TB/3.64 TiB)
[   38.577746] sd 5:0:0:0: [sdc] Write Protect is off
[   38.580833] sd 5:0:0:0: [sdc] Mode Sense: 4f 00 00 00
[   38.584124] sd 5:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[   38.587716] xhci_hcd 0000:05:00.0: ERROR Transfer event for unknown
stream ring slot 3 ep 2
[   38.590251] xhci_hcd 0000:05:00.0: @00000004177fe720 00000000
00000000 1b000000 03038001
[   39.202274] scsi 4:0:0:0: Direct-Access     SanDisk  Ultra Fit
  1.00 PQ: 0 ANSI: 6
[   39.206396] sd 4:0:0:0: Attached scsi generic sg3 type 0
[   39.206563] sd 4:0:0:0: [sdd] 60062500 512-byte logical blocks:
(30.8 GB/28.6 GiB)
[   39.214291] sd 4:0:0:0: [sdd] Write Protect is off
[   39.215672] sd 4:0:0:0: [sdd] Mode Sense: 43 00 00 00
[   39.217941] sd 4:0:0:0: [sdd] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[   39.226274]  sdd: sdd1 sdd2
[   39.229512] sd 4:0:0:0: [sdd] Attached SCSI removable disk
[   39.387065]  sdc: sdc1 sdc2 sdc3
[   39.391307] sd 5:0:0:0: [sdc] Attached SCSI disk
...
[  824.596691] xhci_hcd 0000:05:00.0: remove, state 1
[  824.598852] usb usb4: USB disconnect, device number 1
[  824.601049] usb 4-1: USB disconnect, device number 2
[  824.640171] usb 4-2: USB disconnect, device number 3
[  824.641808] sd 5:0:0:0: [sdc] Synchronizing SCSI cache
[  824.843176] sd 5:0:0:0: [sdc] Synchronize Cache(10) failed: Result:
hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  830.314822] xhci_hcd 0000:05:00.0: xHCI host controller not
responding, assume dead
[  830.317056] xhci_hcd 0000:05:00.0: Timeout while waiting for
configure endpoint command
[  830.317731] systemd-journald[330]: Sent WATCHDOG=1 notification.
[  830.343621] xhci_hcd 0000:05:00.0: WARN Can't disable streams for
endpoint 0x81, streams are being disabled already
[  830.345391] xhci_hcd 0000:05:00.0: USB bus 4 deregistered
[  830.347624] xhci_hcd 0000:05:00.0: remove, state 4
[  830.349612] usb usb3: USB disconnect, device number 1
[  830.352268] xhci_hcd 0000:05:00.0: Host halt failed, -19
[  830.353815] xhci_hcd 0000:05:00.0: Host not accessible, reset failed.
[  830.356083] xhci_hcd 0000:05:00.0: USB bus 3 deregistered
[  830.423760] pci 0000:05:00.0: [1912:0015] type 00 class 0x0c0330
[  830.427547] pci 0000:05:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[  830.429554] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[  830.440012] pci 0000:05:00.0: BAR 0: assigned [mem
0xf1c00000-0xf1c01fff 64bit]
[  830.442460] pci 0000:05:00.0: enabling device (0000 -> 0002)
[  830.445157] xhci_hcd 0000:05:00.0: Resetting
[  831.861255] xhci_hcd 0000:05:00.0: xHCI Host Controller
[  831.861908] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 3
[  831.867877] xhci_hcd 0000:05:00.0: hcc params 0x014051cf hci
version 0x100 quirks 0x00000090
[  831.868964] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[  831.869618] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[  831.870273] usb usb3: Product: xHCI Host Controller
[  831.870924] usb usb3: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[  831.871583] usb usb3: SerialNumber: 0000:05:00.0
[  831.872354] hub 3-0:1.0: USB hub found
[  831.873099] hub 3-0:1.0: 2 ports detected
[  831.873946] xhci_hcd 0000:05:00.0: xHCI Host Controller
[  831.874952] xhci_hcd 0000:05:00.0: new USB bus registered, assigned
bus number 4
[  831.875972] xhci_hcd 0000:05:00.0: Host supports USB 3.0  SuperSpeed
[  831.876889] usb usb4: We don't know the algorithms for LPM for this
host, disabling LPM.
[  831.877604] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[  831.878309] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[  831.879017] usb usb4: Product: xHCI Host Controller
[  831.879730] usb usb4: Manufacturer: Linux 4.16.13-1-ARCH xhci-hcd
[  831.880454] usb usb4: SerialNumber: 0000:05:00.0
[  831.881470] hub 4-0:1.0: USB hub found
[  831.882429] hub 4-0:1.0: 2 ports detected
[  832.203153] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[  832.352142] usb 3-1: New USB device found, idVendor=0781, idProduct=5583
[  832.354748] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  832.357392] usb 3-1: Product: Ultra Fit
[  832.358682] usb 3-1: Manufacturer: SanDisk
[  832.359771] usb 3-1: SerialNumber: 4C531001460907121050
[  832.362990] usb-storage 3-1:1.0: USB Mass Storage device detected
[  832.364336] scsi host4: usb-storage 3-1:1.0
[  832.746493] xhci_hcd 0000:05:00.0: xHCI host controller not
responding, assume dead
[  832.749124] xhci_hcd 0000:05:00.0: HC died; cleaning up
[  833.097573] usb usb4-port2: couldn't allocate usb_device
[  833.097599] usb usb3-port2: couldn't allocate usb_device
[  833.099101] usb 3-1: USB disconnect, device number 2
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux