On Wed, May 02, 2018 at 03:13:44PM +0200, Mats Karrman wrote: > Hi Heikki, > > On 2018-05-02 10:25, Heikki Krogerus wrote: > > > On Wed, May 02, 2018 at 11:23:35AM +0300, Heikki Krogerus wrote: > > > Hi Mats, > > > > > > On Wed, May 02, 2018 at 12:21:07AM +0200, Mats Karrman wrote: > > > > The current naming used for tcpc_mux_mode constants makes > > > > too much assumptioms about the usage of the signals. > > > > This patch replaces the names with generic names more closely > > > > tied to the Type-C specifications and also adds some new ones. > > > > At the same time TCPC_MUX_* defines are removed as they do not > > > > fit the new concept and currently have no in-tree users. > > > I'm afraid trying to generalize the modal connector states even like > > > this is not going to work. We can't make any assumptions about how the > > > alternate modes configure the pins, or the connector in general. > > > > > > The only way this will work is that every alternate mode has its own > > > configurations defined separately, and I'm talking about the actual > > > pin configurations that the specifications for each alternate mode > > > defines, so something like TYPEC_MUX_DP and TYPEC_MUX_DOCK will not > > > work for sure. > > > > > > The connector states that are defined in USB Type-C specification (so > > > basically USB Operation and USB Safe State) can be generalized, but > > > those states just should not be defined in tcpm.h. We need to use > > > them in other drivers as well. > > > > > > I'm in the middle of preparing more complete support for alternate > > > modes. If you check the RFC [1] I send previously, in the first patch > > > of the series I'm adding documentation that should explain the > > > plan. > > Sorry, I forgot the link: > > > > [1] https://www.spinics.net/lists/linux-usb/msg166520.html > > Oh, sorry I forgot about that post in the first place... I reread it now. > > Since the modal TYPEC_STATE_ are overlapping for each AM, this means that > the mux driver "set" must know which AM is active, right? > > And each mux driver also need to support all possible alt modes? There are two options for the mux drivers to link with the alternate modes. They can use the typec API where a single mux is linked to a single port. Alternatively they can use the notifiers from the alternate modes themselves, which allows a single mux to be liked to multiple alternate modes. Both methods will be available. Is this what you were asking? > I was thinking that it must be a finite number of possible routes > between the local connections of a mux and the four available SS lanes of > the cable but of course there is no theoretical limit to the number of > local connections... > > Do we want to set a limitation of one mux device per port? I guess we > could and then let people write "composite" mux drivers if it should ever > be necessary. I think I answered to this one above. > Still it's difficult to write a mux device driver that support everything, > but I'm thinking that it might be possible to write a "mode agnostic" mux > driver that uses properties to match the "AM:STATE" pairs the board needs > to support to the hardware mux device specific muxing modes available? > > It would be very interesting to see a devicetree example on how you > picture things being connected to each other. > > Btw. You're using "mode" and "state" interchangeably which is a bit > confusing. Could you settle for one? OK, I'll try to be more consistent and pick one. Thanks, -- heikki -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
