On Wed, Apr 25, 2018 at 03:45:28PM +0800, Chunfeng Yun wrote:
> Add a DT binding documentation of XS-PHY for MediaTek SoCs
> with USB3.1 GEN2 controller
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
> ---
> .../devicetree/bindings/phy/phy-mtk-xsphy.txt | 127 ++++++++++++++++++++
> 1 file changed, 127 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
> new file mode 100644
> index 0000000..23c51a0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
> @@ -0,0 +1,127 @@
> +MediaTek XS-PHY binding
> +--------------------------
> +
> +The XS-PHY controller supports physical layer functionality for USB3.1
> +GEN2 controller on MediaTek SoCs.
> +
> +Required properties (controller (parent) node):
> + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy",
> + soc-model is the name of SoC, such as mt2712 etc;
Please list all valid SoCs.
> + when using "mediatek,xsphy" compatible string, you need SoC specific
> + ones in addition.
> +
> +Required nodes : a sub-node is required for each port the controller
> + provides. Address range information including the usual
> + 'reg' property is used inside these nodes to describe
> + the controller's topology.
This should go afer the parent optional properties.
> +
> +Optional properties (controller (parent) node):
> + - reg : offset and length of register shared by multiple U3 ports,
> + exclude port's private register, if only U2 ports provided,
> + shouldn't use the property.
> + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate
> + calibrate
> + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on
> + SoC process
> +
> +Required properties (port (child) node):
> +- reg : address and length of the register set for the port.
> +- clocks : a list of phandle + clock-specifier pairs, one for each
> + entry in clock-names
> +- clock-names : must contain
> + "ref": 48M reference clock for HighSpeed analog phy; and 26M
> + reference clock for SuperSpeedPlus analog phy, sometimes is
> + 24M, 25M or 27M, depended on platform.
> +- #phy-cells : should be 1 (See second example)
> + cell after port phandle is phy type from:
> + - PHY_TYPE_USB2
> + - PHY_TYPE_USB3
Is the type a property of the connection to the host? If not, this
shouldn't be part of the phy cells. I would add compatible strings to
the child nodes to define this. I think that would simplify the driver
too as then you can parse DT properties in probe rather than phy_init.
> +
> +The following optional properties are only for debug or HQA test
> +Optional properties (PHY_TYPE_USB2 port (child) node):
> +- mediatek,eye-src : u32, the value of slew rate calibrate
> +- mediatek,eye-vrt : u32, the selection of VRT reference voltage
> +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
> +- mediatek,efuse-intr : u32, the selection of Internal Resistor
> +
> +Optional properties (PHY_TYPE_USB3 port (child) node):
> +- mediatek,efuse-intr : u32, the selection of Internal Resistor
> +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance
> +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance
> +
> +Example:
> +
> +u3phy: usb-phy@11c40000 {
> + compatible = "mediatek,mt36xx-xsphy", "mediatek,xsphy";
Is mt36xx a specific SoC? Don't use wildcards in compatible strings.
> + reg = <0 0x11c43000 0 0x0200>;
> + mediatek,src-ref-clk-mhz = <26>;
> + mediatek,src-coef = <17>;
> + #address-cells = <2>;
> + #size-cells = <2>;
Really need 64-bit sizes?
> + ranges;
Limiting the range to only the phy addresses is preferred.
> + status = "disabled";
Don't show status in examples.
> +
> + u2port0: usb-phy@11c40000 {
> + reg = <0 0x11c40000 0 0x0400>;
> + clocks = <&clk48m>;
> + clock-names = "ref";
> + mediatek,eye-src = <4>;
> + #phy-cells = <1>;
> + status = "okay";
> + };
> +
> + u3port0: usb-phy@11c43000 {
> + reg = <0 0x11c43400 0 0x0500>;
> + clocks = <&clk26m>;
> + clock-names = "ref";
> + mediatek,efuse-intr = <28>;
> + #phy-cells = <1>;
> + status = "okay";
> + };
> +};
> +
> +Specifying phy control of devices
> +---------------------------------
> +
> +Device nodes should specify the configuration required in their "phys"
> +property, containing a phandle to the phy port node and a device type;
> +phy-names for each port are optional.
> +
> +Example:
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +ssusb: usb@112a0000 {
> + ...
> + phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
> + phy-names = "usb2-0", "usb3-0";
> + ...
> +};
This section is not necessary. We've already explained how to use the
phy binding elsewhere.
> +
> +
> +Banks layout of xsphy
Put this before the example.
> +-------------------------------------------------------------
> +port offset bank
> +u2 port0 0x0000 MISC
> + 0x0100 FMREG
> + 0x0300 U2PHY_COM
> +u2 port1 0x1000 MISC
> + 0x1100 FMREG
> + 0x1300 U2PHY_COM
> +u2 port2 0x2000 MISC
> + ...
> +u31 common 0x3000 DIG_GLB
> + 0x3100 PHYA_GLB
> +u31 port0 0x3400 DIG_LN_TOP
> + 0x3500 DIG_LN_TX0
> + 0x3600 DIG_LN_RX0
> + 0x3700 DIG_LN_DAIF
> + 0x3800 PHYA_LN
> +u31 port1 0x3a00 DIG_LN_TOP
> + 0x3b00 DIG_LN_TX0
> + 0x3c00 DIG_LN_RX0
> + 0x3d00 DIG_LN_DAIF
> + 0x3e00 PHYA_LN
> + ...
> +
> +DIG_GLB & PHYA_GLB are shared by U31 ports.
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
