On Tue, Mar 13, 2018 at 04:06:00PM +0530, Manu Gautam wrote: > Existing documentation has lot of incorrect information as it > was originally added for a driver that no longer exists. > > Signed-off-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx> > --- > .../devicetree/bindings/usb/qcom,dwc3.txt | 87 +++++++++++++++------- > 1 file changed, 59 insertions(+), 28 deletions(-) > > diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt > index bc8a2fa..df312f7 100644 > --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt > +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt > @@ -1,54 +1,85 @@ > Qualcomm SuperSpeed DWC3 USB SoC controller > > Required properties: > -- compatible: should contain "qcom,dwc3" > -- clocks: A list of phandle + clock-specifier pairs for the > - clocks listed in clock-names > -- clock-names: Should contain the following: > - "core" Master/Core clock, have to be >= 125 MHz for SS > - operation and >= 60MHz for HS operation > - > -Optional clocks: > - "iface" System bus AXI clock. Not present on all platforms > - "sleep" Sleep clock, used when USB3 core goes into low > - power mode (U3). > +- compatible: should contain "qcom,dwc3" > +- reg: offset and length of register set for QSCRATCH wrapper > +- reg-names: should be "qscratch" reg-names is pointless for a single range. > +- power-domains: specifies a phandle to PM domain provider node > +- clocks: list of phandle + clock-specifier pairs How many clocks and what are they? > +- assigned-clocks: should be: > + MOCK_UTMI_CLK > + MASTER_CLK > +- assigned-clock-rates: should be: > + 19.2Mhz (192000000) for MOCK_UTMI_CLK > + >=125Mhz (125000000) for MASTER_CLK in SS mode > + >=60Mhz (60000000) for MASTER_CLK in HS mode > + > +Optional properties: > +- resets: list of phandle and reset specifier pairs > +- interrupts: specifies interrupts from controller wrapper used > + to wakeup from low power/susepnd state. Must contain > + one or more entry for interrupt-names property > +- interrupt-names: Must include the following entries: > + - "hs_phy_irq": The interrupt that is asserted when a > + wakeup event is received on USB2 bus > + - "ss_phy_irq": The interrupt that is asserted when a > + wakeup event is received on USB3 bus > + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate > + interrupts for any wakeup event on DM and DP lines > +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. > + Used when dwc3 operates without SSPHY and only > + HS/FS/LS modes are supported. > > Required child node: > A child node must exist to represent the core DWC3 IP block. The name of > the node is not important. The content of the node is defined in dwc3.txt. > > Phy documentation is provided in the following places: > -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt > +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY > +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
