On Fri, 16 Feb 2018 13:13:11 -0500 (EST)
Alan Stern <stern@xxxxxxxxxxxxxxxxxxx> wrote:
> On Fri, 16 Feb 2018, Andreas Kemnade wrote:
>
> > This powers down the phy and on a gta04 it reduces
> > suspend current by 13 mA.
> > For unknown reasons usb does not power on properly.
> > Also calling usb_phy_shutdown() here feels wrong
> > apparently the reset line has to be activated.
> > usb_phy_set_suspend is not enough here. The power
> > consumption still stays approximately the same as
> > without any patch.
> >
> > With a device connected the device does not enumerate
> > after resume. A rmmod ehci-omap ; modprobe ehci-omap
> > does not make it reenumerade.
> > So there is still something wrong here.
> >
> > Signed-off-by: Andreas Kemnade <andreas@xxxxxxxxxxxx>
> > ---
> > drivers/usb/host/ehci-omap.c | 59 ++++++++++++++++++++++++++++++++++++++++++--
> > 1 file changed, 57 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
> > index 8d8bafc70c1f..0be2ccf8182a 100644
> > --- a/drivers/usb/host/ehci-omap.c
> > +++ b/drivers/usb/host/ehci-omap.c
> > @@ -266,6 +266,58 @@ static int ehci_hcd_omap_remove(struct platform_device *pdev)
> > return 0;
> > }
> >
> > +
> > +static int __maybe_unused ehci_omap_suspend(struct device *dev)
> > +{
> > + struct usb_hcd *hcd = dev_get_drvdata(dev);
> > + struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
> > + int ret;
> > + int i;
> > +
> > + ret = ehci_suspend(hcd, false);
> > + if (ret) {
> > + dev_err(dev, "ehci suspend failed: %d\n", ret);
> > + return ret;
> > + }
> > + for (i = 0; i < omap->nports; i++) {
> > + if (omap->phy[i])
> > + usb_phy_shutdown(omap->phy[i]);
> > + }
> > + pm_runtime_put_sync(dev);
>
> Why do you include a runtime PM call here, given that the driver
> doesn't support runtime suspend or resume?
>
Well, the parent (drivers/mfd/omap-usb-host.c) has, and there are runtime PM
calls here in the _probe/_remove functions, so it seems to be sane to do it
here, too.
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused ehci_omap_resume(struct device *dev)
> > +{
> > + struct usb_hcd *hcd = dev_get_drvdata(dev);
> > + struct omap_hcd *omap = (struct omap_hcd *)hcd_to_ehci(hcd)->priv;
> > + int i;
> > +
> > + pm_runtime_get_sync(dev);
> > + /*
> > + * An undocumented "feature" in the OMAP3 EHCI controller,
> > + * causes suspended ports to be taken out of suspend when
> > + * the USBCMD.Run/Stop bit is cleared (for example when
> > + * we do ehci_bus_suspend).
> > + * This breaks suspend-resume if the root-hub is allowed
> > + * to suspend. Writing 1 to this undocumented register bit
> > + * disables this feature and restores normal behavior.
> > + */
> > + ehci_write(hcd->regs, EHCI_INSNREG04,
> > + EHCI_INSNREG04_DISABLE_UNSUSPEND);
>
> Doesn't this code belong in ehci_hcd_omap_probe()? I assume you only
> need to set this undocumented bit once, not every time the controller
> is suspended. And in any case, according to the comment, you would
> need to take care of this before the root hub is suspended -- by the
> time the controller is suspended, it is already too late.
>
I am not really sure about this one. It is set in ehci_hcd_omap_probe()
so it is set before suspend. I set it here to ensure it is re-set when
the controller is powered down too much to keep register contents. I
do not know if that is the case. But I thought it would not harm.
Regards,
Andreas
Attachment:
pgpwSWDWJW0gw.pgp
Description: OpenPGP digital signature
