QMP V3 USB3 PHY is a DisplayPort (DP) and USB combo PHY
with dual RX/TX lanes to support type-c. There is a
separate block DP_COM for configuration related to type-c
or DP. Add support for dp_com region and secondary rx/tx
lanes initialization.
Signed-off-by: Manu Gautam <mgautam@xxxxxxxxxxxxxx>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 223 +++++++++++++++++++++++++++++++++++-
1 file changed, 220 insertions(+), 3 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 2a1117b..55b8397 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -47,6 +47,21 @@
/* QPHY_COM_PCS_READY_STATUS bit */
#define PCS_READY BIT(0)
+/* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
+/* DP PHY soft reset */
+#define SW_DPPHY_RESET BIT(0)
+/* mux to select DP PHY reset control, 0:HW control, 1: software reset */
+#define SW_DPPHY_RESET_MUX BIT(1)
+/* USB3 PHY soft reset */
+#define SW_USB3PHY_RESET BIT(2)
+/* mux to select USB3 PHY reset control, 0:HW control, 1: software reset */
+#define SW_USB3PHY_RESET_MUX BIT(3)
+
+/* QPHY_V3_DP_COM_PHY_MODE_CTRL register bits */
+#define USB3_MODE BIT(0) /* enables USB3 mode */
+#define DP_MODE BIT(1) /* enables DP mode */
+
+
#define PHY_INIT_COMPLETE_TIMEOUT 1000
#define POWER_DOWN_DELAY_US_MIN 10
#define POWER_DOWN_DELAY_US_MAX 11
@@ -122,6 +137,12 @@ enum qphy_reg_layout {
[QPHY_PCS_READY_STATUS] = 0x17c,
};
+static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x174,
+};
+
static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
@@ -350,6 +371,112 @@ enum qphy_reg_layout {
QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
};
+static const struct qmp_phy_init_tbl qmp_v3_usb3_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_pcs_tbl[] = {
+ /* FLL settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+ /* Lock Det settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+};
+
/* struct qmp_phy_cfg - per-PHY initialization config */
struct qmp_phy_cfg {
/* phy-type - PCIE/UFS/USB */
@@ -394,6 +521,12 @@ struct qmp_phy_cfg {
/* power_down delay in usec */
int pwrdn_delay_min;
int pwrdn_delay_max;
+
+ /* true, if PHY has a separate DP_COM control block */
+ bool has_phy_dp_com_ctrl;
+ /* Register offset of secondary tx/rx lanes for USB DP combo PHY */
+ unsigned int tx_b_lane_offset;
+ unsigned int rx_b_lane_offset;
};
/**
@@ -424,6 +557,7 @@ struct qmp_phy {
*
* @dev: device
* @serdes: iomapped memory space for phy's serdes
+ * @dp_com: iomapped memory space for phy's dp_com control block
*
* @clks: array of clocks required by phy
* @resets: array of resets required by phy
@@ -437,6 +571,7 @@ struct qmp_phy {
struct qcom_qmp {
struct device *dev;
void __iomem *serdes;
+ void __iomem *dp_com;
struct clk_bulk_data *clks;
struct reset_control **resets;
@@ -478,6 +613,10 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
"aux", "cfg_ahb", "ref",
};
+static const char * const qmp_v3_phy_clk_l[] = {
+ "aux", "cfg_ahb", "ref", "com_aux",
+};
+
/* list of resets */
static const char * const msm8996_pciephy_reset_l[] = {
"phy", "common", "cfg",
@@ -584,6 +723,38 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.pwrdn_delay_max = 1005, /* us */
};
+static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = qmp_v3_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
+ .tx_tbl = qmp_v3_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
+ .rx_tbl = qmp_v3_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
+ .pcs_tbl = qmp_v3_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
+ .clk_list = qmp_v3_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = qmp_v3_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PHYSTATUS,
+
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .tx_b_lane_offset = 0x400,
+ .rx_b_lane_offset = 0x400,
+};
+
static void qcom_qmp_phy_configure(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
@@ -620,6 +791,7 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
{
const struct qmp_phy_cfg *cfg = qmp->cfg;
void __iomem *serdes = qmp->serdes;
+ void __iomem *dp_com = qmp->dp_com;
int ret, i;
mutex_lock(&qmp->phy_mutex);
@@ -663,6 +835,23 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
SW_PWRDN);
+ if (cfg->has_phy_dp_com_ctrl) {
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
+ SW_PWRDN);
+ /* override hardware control for reset of qmp phy */
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+ SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+ SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
+ USB3_MODE | DP_MODE);
+
+ /* bring both QMP USB and QMP DP PHYs PCS block out of reset */
+ qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+ SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+ SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+ }
+
/* Serdes configuration */
qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
cfg->serdes_tbl_num);
@@ -746,6 +935,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
void __iomem *tx = qphy->tx;
void __iomem *rx = qphy->rx;
void __iomem *pcs = qphy->pcs;
+ void __iomem *dp_com = qmp->dp_com;
void __iomem *status;
unsigned int mask, val;
int ret;
@@ -767,7 +957,16 @@ static int qcom_qmp_phy_init(struct phy *phy)
/* Tx, Rx, and PCS configurations */
qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+ /* Configuration for other LANE for USB-DP combo PHY */
+ if (cfg->has_phy_dp_com_ctrl)
+ qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
+ cfg->tx_tbl, cfg->tx_tbl_num);
+
qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+ if (cfg->has_phy_dp_com_ctrl)
+ qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
+ cfg->rx_tbl, cfg->rx_tbl_num);
+
qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
/*
@@ -781,6 +980,8 @@ static int qcom_qmp_phy_init(struct phy *phy)
/* Pull PHY out of reset state */
qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+ if (cfg->has_phy_dp_com_ctrl)
+ qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
/* start SerDes and Phy-Coding-Sublayer */
qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
@@ -1031,6 +1232,9 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
}, {
.compatible = "qcom,ipq8074-qmp-pcie-phy",
.data = &ipq8074_pciephy_cfg,
+ }, {
+ .compatible = "qcom,qmp-v3-usb3-phy",
+ .data = &qmp_v3_usb3phy_cfg,
},
{ },
};
@@ -1054,6 +1258,11 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
qmp->dev = dev;
dev_set_drvdata(dev, qmp);
+ /* Get the specific init parameters of QMP phy */
+ qmp->cfg = of_device_get_match_data(dev);
+ if (!qmp->cfg)
+ return -EINVAL;
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(dev, res);
if (IS_ERR(base))
@@ -1062,10 +1271,18 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
/* per PHY serdes; usually located at base address */
qmp->serdes = base;
- mutex_init(&qmp->phy_mutex);
+ /* per PHY dp_com; if PHY has dp_com control block */
+ if (qmp->cfg->has_phy_dp_com_ctrl) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "dp_com");
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
- /* Get the specific init parameters of QMP phy */
- qmp->cfg = of_device_get_match_data(dev);
+ qmp->dp_com = base;
+ }
+
+ mutex_init(&qmp->phy_mutex);
ret = qcom_qmp_phy_clk_init(dev);
if (ret)
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
