On 10/17/2017 12:41 PM, Minas Harutyunyan wrote:
> On 10/17/2017 1:34 AM, John Stultz wrote:
>> On Mon, Oct 16, 2017 at 1:36 AM, Minas Harutyunyan
>> <Minas.Harutyunyan@xxxxxxxxxxxx> wrote:
>>> On b-plug disconnect should asserted GOTGINT.SesEndDet interrupt.
>>> According previously sent by you register dump (GHWCFG2 = 0x23affc70)
>>> your core OTG_MODE=0.
>>> Bellow fragment from programming guide on Device disconnect:
>>>
>>> "7.3Device Disconnection
>>> The device session ends when the USB cable is disconnected or if the
>>> VBUS is switched off by the Host. The
>>> device disconnect flow varies depending on the value of the OTG_MODE
>>> configuration parameter.
>>>
>>> When OTG_MODE = 0,1, or 3
>>> When OTG_MODE is set to 0,1, or 3, the device disconnect flow is as follows:
>>> 1. When the USB cable is unplugged or when the VBUS is switched off by
>>> the Host, the Device core
>>> trigger GINTSTS.OTGInt [bit 2] interrupt bit.
>>> 2. When the device application detects GINTSTS.OTGInt interrupt, it
>>> checks that the
>>> GOTGINT.SesEndDet (Session End Detected) bit is set to 1’b1."
>>>
>>> So, you should receive and handle "Session End Detected". In function
>>> dwc2_handle_otg_intr() on this interrupt (in device mode) calling
>>> dwc2_hsotg_disconnect() function. By adding your patch "[PATCH 3/3] usb:
>>> dwc2: Fix UDC state tracking" state changed to not attached as required.
>>
>>
>> So, on the HiKey board (using 4.14-rc5 + Vardan's patch), I'm not
>> seeing the GOTGINT_SES_END_DET in dwc2_handle_otg_intr() when I remove
>> the USB OTG cable.
>>
>> In fact, I'm not seeing any calls to dwc2_handle_otg_intr()... which
>> seems... odd maybe? Any clues as to what might be going wrong then?
>>
>> thanks
>> -john
>>
> Hi John Stultz,
> So, on Hikey board on unplug B connector GOTGINT.SesEndDet interrupt not
> asserted, instead asserted GINTSTS_CONIDSTSCHNG. Please, confirm.
>
> In this case without your patch "[PATCH 1/3] usb: dwc2: Improve gadget
> state disconnection handling" but by applying your patch "[PATCH 3/3]
> usb: dwc2: Fix UDC state tracking":
> 1. On B plug connect UDC state will be set to "configured"
> 2. On B plug disconnect - "not attached".
> Is it Ok for you?
>
> Meantime, I'll check with HW team why GOTGINT.SesEndDet interrupt not
> asserted on unplug B connector.
>
> Thanks,
> Minas
>
Hi John Stultz,
Could you please apply this patch. Please not apply your patch series
"[PATCH 0/3] dwc2 fixes for edge cases on hikey" to check only below patch.
If you confirm that this patch fix your issue with "Transaction Error"
and " ChHltd set, but reason is unknown" I'll submit to LKML as final patch.
Then can be applied your patch series, without patch 1/3 (changing in
connector id status change) to correctly set UDC states.
diff --git a/drivers/usb/dwc2/hcd.c b/drivers/usb/dwc2/hcd.c index
f4ef159b538e..7da22152df68 100644
--- a/drivers/usb/dwc2/hcd.c
+++ b/drivers/usb/dwc2/hcd.c
@@ -331,6 +331,9 @@ static void dwc2_gusbcfg_init(struct dwc2_hsotg *hsotg)
usbcfg = dwc2_readl(hsotg->regs + GUSBCFG);
usbcfg &= ~(GUSBCFG_HNPCAP | GUSBCFG_SRPCAP);
+ /* Set HS/FS Timeout Calibration */
+ usbcfg |= GUSBCFG_TOUTCAL(7);
+
switch (hsotg->hw_params.op_mode) {
case GHWCFG2_OP_MODE_HNP_SRP_CAPABLE:
if (hsotg->params.otg_cap ==
Thanks,
Minas
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
