The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@xxxxxxxxx>
---
drivers/tty/serial/atmel_serial.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 7551cab438ff..783af6648be0 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -171,6 +171,7 @@ struct atmel_uart_port {
bool has_hw_timer;
struct timer_list uart_timer;
+ bool tx_stopped;
bool suspended;
unsigned int pending;
unsigned int pending_status;
@@ -380,6 +381,10 @@ static int atmel_config_rs485(struct uart_port *port,
*/
static u_int atmel_tx_empty(struct uart_port *port)
{
+ struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+ if (atmel_port->tx_stopped)
+ return TIOCSER_TEMT;
return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
TIOCSER_TEMT :
0;
@@ -485,6 +490,7 @@ static void atmel_stop_tx(struct uart_port *port)
* is fully transmitted.
*/
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
+ atmel_port->tx_stopped = true;
/* Disable interrupts */
atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
@@ -492,6 +498,7 @@ static void atmel_stop_tx(struct uart_port *port)
if ((port->rs485.flags & SER_RS485_ENABLED) &&
!(port->rs485.flags & SER_RS485_RX_DURING_TX))
atmel_start_rx(port);
+
}
/*
@@ -521,6 +528,7 @@ static void atmel_start_tx(struct uart_port *port)
/* re-enable the transmitter */
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+ atmel_port->tx_stopped = false;
}
/*
@@ -1866,6 +1874,7 @@ static int atmel_startup(struct uart_port *port)
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
/* enable xmit & rcvr */
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+ atmel_port->tx_stopped = false;
setup_timer(&atmel_port->uart_timer,
atmel_uart_timer_callback,
@@ -2122,6 +2131,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
/* disable receiver and transmitter */
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
+ atmel_port->tx_stopped = true;
/* mode */
if (port->rs485.flags & SER_RS485_ENABLED) {
@@ -2207,6 +2217,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
atmel_uart_writel(port, ATMEL_US_BRGR, quot);
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+ atmel_port->tx_stopped = false;
/* restore interrupts */
atmel_uart_writel(port, ATMEL_US_IER, imr);
@@ -2450,6 +2461,7 @@ static void atmel_console_write(struct console *co, const char *s, u_int count)
/* Make sure that tx path is actually able to send characters */
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
+ atmel_port->tx_stopped = false;
uart_console_write(port, s, count, atmel_console_putchar);
@@ -2511,6 +2523,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
{
int ret;
struct uart_port *port = &atmel_ports[co->index].uart;
+ struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
int baud = 115200;
int bits = 8;
int parity = 'n';
@@ -2528,6 +2541,7 @@ static int __init atmel_console_setup(struct console *co, char *options)
atmel_uart_writel(port, ATMEL_US_IDR, -1);
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
+ atmel_port->tx_stopped = false;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
