Em Thu, 30 Mar 2017 12:38:42 +0300 Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> escreveu: > Hi Mauro, > > On Wednesday 29 Mar 2017 22:06:33 Mauro Carvalho Chehab wrote: > > Em Thu, 30 Mar 2017 01:15:27 +0300 Laurent Pinchart escreveu: > > > On Wednesday 29 Mar 2017 15:54:21 Mauro Carvalho Chehab wrote: > > > > Several host controllers, commonly found on ARM, like dwc2, > > > > require buffers that are CPU-word aligned for they to work. > > > > > > > > Failing to do that will cause random troubles at the caller > > > > drivers, causing them to fail. > > > > > > > > Document it. > > > > > > > > Signed-off-by: Mauro Carvalho Chehab <mchehab@xxxxxxxxxxxxxxxx> > > > > --- > > > > > > > > Documentation/driver-api/usb/URB.rst | 18 ++++++++++++++++++ > > > > drivers/usb/core/message.c | 15 +++++++++++++++ > > > > include/linux/usb.h | 18 ++++++++++++++++++ > > > > 3 files changed, 51 insertions(+) > > > > > > > > diff --git a/Documentation/driver-api/usb/URB.rst > > > > b/Documentation/driver-api/usb/URB.rst index d9ea6a3996e7..b83b557e9891 > > > > 100644 > > > > --- a/Documentation/driver-api/usb/URB.rst > > > > +++ b/Documentation/driver-api/usb/URB.rst > > > > @@ -274,6 +274,24 @@ If you specify your own start frame, make sure it's > > > > several frames in advance of the current frame. You might want this > > > > model > > > > if you're synchronizing ISO data with some other event stream. > > > > > > > > +.. note:: > > > > + > > > > + Several host drivers require that the ``transfer_buffer`` to be > > > > aligned > > > > + with the CPU word size (e. g. DWORD for 32 bits, QDWORD for 64 > > > > bits). > > > > > > Is it the CPU word size or the DMA transfer size ? I assume the latter, > > > and I wouldn't be surprised if the alignment requirement was 32-bit on at > > > least some of the 64-bit platforms. > > > > Yeah, it is actually the DMA transfer size. Yet, worse case scenario is that > > the DMA transfer size to be 64 bits on 64 bits CPU. > > > > > > + It is up to USB drivers should ensure that they'll only pass buffers > > > > + with such alignments. > > > > + > > > > + Please also notice that, due to such restriction, the host driver > > > > > > s/notice/note/ (and below as well) ? > > > > OK. > > > > > > + may also override PAD bytes at the end of the ``transfer_buffer``, > > > > up to the > > > > + size of the CPU word. > > > > > > "May" is quite weak here. If some host controller drivers require buffers > > > to be aligned, then it's an API requirement, and all buffers must be > > > aligned. I'm not even sure I would mention that some host drivers require > > > it, I think we should just state that the API requires buffers to be > > > aligned. > > > > What I'm trying to say here is that, on a 32-bits system, if the driver do > > a USB_DIR_IN transfer using some code similar to: > > > > size = 4; > > buffer = kmalloc(size, GFP_KERNEL); > > > > usb_control_msg(udev, pipe, req, type, val, idx, buffer + 2, 2, > timeout); > > usb_control_msg(udev, pipe, req, type, val, idx, buffer, size, > timeout); > > > > Drivers like dwc2 will mess with the buffer. > > > > The first transfer will actually work, due to a workaround inside the > > driver that will create a temporary DWORD-aligned buffer, avoiding it > > to go past the buffer. > > > > However, the second transfer will destroy the data received from the > > first usb_control_msg(), as it will write 4 bytes at the buffer. > > > > Not all drivers would do that, though. > > > > Please notice that, as kmalloc will always return a CPU-aligned buffer, > > if the client do something like: > > > > size = 2; > > buffer = kmalloc(size, GFP_KERNEL); > > > > usb_control_msg(udev, pipe, req, type, val, idx, buffer, 2, timeout); > > > > What happens there is that the DMA engine will still write 4 bytes at > > the buffer, but the 2 bytes that go past the end of buffer will be > > written on a memory that will never be used. > > I understand that, but stating that host controller drivers "may" do this > won't help much. If they *may*, all USB device drivers *must* align buffers > correctly. That's the part that needs to be documented. Let's not confuse > developers by only stating that something may happened, let's be clear and > tell what they must do. Ok, rewrote the entire text. Please see if the new version works better. > > > > > + Please notice that ancillary routines that transfer URBs, like > > > > + usb_control_msg() also have such restriction. > > > > + > > > > + Such word alignment condition is normally ensured if the buffer is > > > > + allocated with kmalloc(), but this may not be the case if the driver > > > > + allocates a bigger buffer and point to a random place inside it. > > > > + > > > > > > > > How to start interrupt (INT) transfers? > > > > ======================================= > > > > > > > > diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c > > > > index 4c38ea41ae96..1662a4446475 100644 > > > > --- a/drivers/usb/core/message.c > > > > +++ b/drivers/usb/core/message.c > > > > @@ -128,6 +128,21 @@ static int usb_internal_control_msg(struct > > > > usb_device > > > > *usb_dev, * make sure your disconnect() method can wait for it to > > > > complete. > > > > Since you * don't have a handle on the URB used, you can't cancel the > > > > request. * > > > > + * .. note:: > > > > + * > > > > + * Several host drivers require that the @data buffer to be aligned > > > > + * with the CPU word size (e. g. DWORD for 32 bits, QDWORD for 64 > > > > bits). > > > > + * It is up to USB drivers should ensure that they'll only pass > > > > buffers > > > > + * with such alignments. > > > > + * > > > > + * Please also notice that, due to such restriction, the host driver > > > > + * may also override PAD bytes at the end of the @data buffer, up to > > > > the > > > > + * size of the CPU word. > > > > + * > > > > + * Such word alignment condition is normally ensured if the buffer is > > > > + * allocated with kmalloc(), but this may not be the case if the > > > > driver > > > > + * allocates a bigger buffer and point to a random place inside it. > > > > + * > > > > > > > > * Return: If successful, the number of bytes transferred. Otherwise, a > > > > > > > > negative * error number. > > > > > > > > */ > > > > > > > > diff --git a/include/linux/usb.h b/include/linux/usb.h > > > > index 7e68259360de..8b5ad6624708 100644 > > > > --- a/include/linux/usb.h > > > > +++ b/include/linux/usb.h > > > > @@ -1373,6 +1373,24 @@ typedef void (*usb_complete_t)(struct urb *); > > > > > > > > * capable, assign NULL to it, so that usbmon knows not to use the > > > > value. > > > > * The setup_packet must always be set, so it cannot be located in > > > > highmem. > > > > > > > > * > > > > + * .. note:: > > > > + * > > > > + * Several host drivers require that the @transfer_buffer to be > > > > aligned > > > > + * with the CPU word size (e. g. DWORD for 32 bits, QDWORD for 64 > > > > bits). > > > > + * It is up to USB drivers should ensure that they'll only pass > > > > buffers > > > > + * with such alignments. > > > > + * > > > > + * Please also notice that, due to such restriction, the host driver > > > > + * may also override PAD bytes at the end of the @transfer_buffer, up > > > > to > > > > the + * size of the CPU word. > > > > + * > > > > + * Please notice that ancillary routines that start URB transfers, > > > > like > > > > + * usb_control_msg() also have such restriction. > > > > + * > > > > + * Such word alignment condition is normally ensured if the buffer is > > > > + * allocated with kmalloc(), but this may not be the case if the > > > > driver > > > > + * allocates a bigger buffer and point to a random place inside it. > > > > + * > > > > > > Couldn't we avoid three copies of the same text ? The chance they will get > > > out-of-sync is quite high. > > > > IMHO, it is better to document it at those 3 parts, as this issue > > cause buffer overflows, which is pretty serious, as it corrupts data. > > > > The URB.rst file contains a quick overview of the URB data transfers, > > and it is likely where a kernel newbie would read first. Experienced > > programmers will look at urb.h. > > > > usb_control_msg() is a different function, that one might not be > > expecting to have the same issues. > > If you add the complete explanation to URB.rst, you can then reference it from > the functions' kerneldoc instead of copying it. True, but URB.txt has a note saying that the document may not be fully updated, implying that urb.h header is the main reference. So, I stand that the best here is to have this warning duplicated, as this is a pretty serious issue and will require people to review all USB drivers. Thanks, Mauro -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
