This patch adds support for the extended range of baud rates supported by CP2102 and CP2103 devices described in SiLabs AN205.
An additional function cp2101_quantise_baudrate rounds the baud rate as per AN205 Table 1.
A modification to the baud rate calculation removes a rounding error, allowing the full range of baud rates to be used.
Signed-off-by: Craig Shelley <craig@xxxxxxxxxxxxxxxx>
---
drivers/usb/serial/cp2101.c | 92 ++++++++++++++++++++++++-------------------
1 files changed, 52 insertions(+), 40 deletions(-)
diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c
index 027f4b7..647967e 100644
--- a/drivers/usb/serial/cp2101.c
+++ b/drivers/usb/serial/cp2101.c
@@ -31,7 +31,7 @@
/*
* Version Information
*/
-#define DRIVER_VERSION "v0.07"
+#define DRIVER_VERSION "v0.08"
#define DRIVER_DESC "Silicon Labs CP2101/CP2102 RS232 serial adaptor driver"
/*
@@ -300,6 +300,47 @@ static inline int cp2101_set_config_single(struct usb_serial_port *port,
return cp2101_set_config(port, request, &data, 2);
}
+/*
+ * cp2101_quantise_baudrate
+ * Quantises the baud rate as per AN205 Table 1
+ */
+static unsigned int cp2101_quantise_baudrate(unsigned int baud) {
+ if (baud <= 56) baud = 0;
+ else if (baud <= 300) baud = 300;
+ else if (baud <= 600) baud = 600;
+ else if (baud <= 1200) baud = 1200;
+ else if (baud <= 1800) baud = 1800;
+ else if (baud <= 2400) baud = 2400;
+ else if (baud <= 4000) baud = 4000;
+ else if (baud <= 4803) baud = 4800;
+ else if (baud <= 7207) baud = 7200;
+ else if (baud <= 9612) baud = 9600;
+ else if (baud <= 14428) baud = 14400;
+ else if (baud <= 16062) baud = 16000;
+ else if (baud <= 19250) baud = 19200;
+ else if (baud <= 28912) baud = 28800;
+ else if (baud <= 38601) baud = 38400;
+ else if (baud <= 51558) baud = 51200;
+ else if (baud <= 56280) baud = 56000;
+ else if (baud <= 58053) baud = 57600;
+ else if (baud <= 64111) baud = 64000;
+ else if (baud <= 77608) baud = 76800;
+ else if (baud <= 117028) baud = 115200;
+ else if (baud <= 129347) baud = 128000;
+ else if (baud <= 156868) baud = 153600;
+ else if (baud <= 237832) baud = 230400;
+ else if (baud <= 254234) baud = 250000;
+ else if (baud <= 273066) baud = 256000;
+ else if (baud <= 491520) baud = 460800;
+ else if (baud <= 567138) baud = 500000;
+ else if (baud <= 670254) baud = 576000;
+ else if (baud <= 1053257) baud = 921600;
+ else if (baud <= 1474560) baud = 1228800;
+ else if (baud <= 2457600) baud = 1843200;
+ else baud = 3686400;
+ return baud;
+}
+
static int cp2101_open(struct tty_struct *tty, struct usb_serial_port *port,
struct file *filp)
{
@@ -387,7 +428,7 @@ static void cp2101_get_termios (struct tty_struct *tty)
cp2101_get_config(port, CP2101_BAUDRATE, &baud, 2);
/* Convert to baudrate */
if (baud)
- baud = BAUD_RATE_GEN_FREQ / baud;
+ baud = cp2101_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
dbg("%s - baud rate = %d", __func__, baud);
@@ -516,46 +557,17 @@ static void cp2101_set_termios(struct tty_struct *tty,
tty->termios->c_cflag &= ~CMSPAR;
cflag = tty->termios->c_cflag;
old_cflag = old_termios->c_cflag;
- baud = tty_get_baud_rate(tty);
+ baud = cp2101_quantise_baudrate(tty_get_baud_rate(tty));
/* If the baud rate is to be updated*/
- if (baud != tty_termios_baud_rate(old_termios)) {
- switch (baud) {
- case 0:
- case 600:
- case 1200:
- case 1800:
- case 2400:
- case 4800:
- case 7200:
- case 9600:
- case 14400:
- case 19200:
- case 28800:
- case 38400:
- case 55854:
- case 57600:
- case 115200:
- case 127117:
- case 230400:
- case 460800:
- case 921600:
- case 3686400:
- break;
- default:
- baud = 9600;
- break;
- }
-
- if (baud) {
- dbg("%s - Setting baud rate to %d baud", __func__,
- baud);
- if (cp2101_set_config_single(port, CP2101_BAUDRATE,
- (BAUD_RATE_GEN_FREQ / baud))) {
- dev_err(&port->dev, "Baud rate requested not "
- "supported by device\n");
- baud = tty_termios_baud_rate(old_termios);
- }
+ if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
+ dbg("%s - Setting baud rate to %d baud", __func__,
+ baud);
+ if (cp2101_set_config_single(port, CP2101_BAUDRATE,
+ ((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
+ dev_err(&port->dev, "Baud rate requested not "
+ "supported by device\n");
+ baud = tty_termios_baud_rate(old_termios);
}
}
/* Report back the resulting baud rate */
--
1.4.4.4
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
