On 10/03/2017 17:45, Mason wrote:
> Time to clean up a million hacks to be able to discuss the finer points.
Here is my current boot log:
[ 1.133895] OF: PCI: host bridge /soc/pcie@50000000 ranges:
[ 1.139607] pci_add_resource_offset: res=[bus 00-0f] offset=0x0
[ 1.145659] OF: PCI: Parsing ranges property...
[ 1.150316] OF: PCI: MEM 0x54000000..0x5fffffff -> 0x04000000
[ 1.156364] pci_add_resource_offset: res=[mem 0x54000000-0x5fffffff] offset=0x50000000
[ 1.164628] pci_tango 50000000.pcie: ECAM at [mem 0x50000000-0x50ffffff] for [bus 00-0f]
[ 1.173033] pci_tango 50000000.pcie: PCI host bridge to bus 0000:00
[ 1.179440] pci_bus 0000:00: root bus resource [bus 00-0f]
[ 1.185056] pci_bus 0000:00: root bus resource [mem 0x54000000-0x5fffffff] (bus address [0x04000000-0x0fffffff])
[ 1.195386] pci_bus 0000:00: scanning bus
[ 1.199539] pci 0000:00:00.0: [1105:0024] type 01 class 0x048000
[ 1.205691] pci 0000:00:00.0: calling tango_pcie_fixup_class+0x0/0x10
[ 1.212277] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x3fffffff 64bit]
[ 1.219220] pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 1.225570] pci 0000:00:00.0: supports D1 D2
[ 1.229957] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
[ 1.236092] pci 0000:00:00.0: PME# disabled
[ 1.240576] pci_bus 0000:00: fixups for bus
[ 1.244886] PCI: bus0: Fast back to back transfers disabled
[ 1.250587] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.257420] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.265567] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.272517] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-0f] (conflicts with (null) [bus 00-0f])
[ 1.283462] pci_bus 0000:01: scanning bus
[ 1.287623] pci 0000:01:00.0: [1912:0014] type 00 class 0x0c0330
[ 1.293799] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 1.300799] pci 0000:01:00.0: calling pci_fixup_ide_bases+0x0/0x40
[ 1.307223] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.313446] pci 0000:01:00.0: PME# disabled
[ 1.318053] pci_bus 0000:01: fixups for bus
[ 1.322362] PCI: bus1: Fast back to back transfers disabled
[ 1.328060] pci_bus 0000:01: bus scan returning with max=01
[ 1.333759] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.340506] pci_bus 0000:00: bus scan returning with max=01
[ 1.346205] pci 0000:00:00.0: fixup irq: got 0
[ 1.350765] pci 0000:00:00.0: assigning IRQ 00
[ 1.355332] pci 0000:01:00.0: fixup irq: got 0
[ 1.359892] pci 0000:01:00.0: assigning IRQ 00
[ 1.364479] pci 0000:00:00.0: BAR 0: no space for [mem size 0x40000000 64bit]
[ 1.371748] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x40000000 64bit]
[ 1.379369] pci 0000:00:00.0: BAR 8: assigned [mem 0x54000000-0x540fffff]
[ 1.386291] pci 0000:01:00.0: BAR 0: assigned [mem 0x54000000-0x54001fff 64bit]
[ 1.393747] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.398833] pci 0000:00:00.0: bridge window [mem 0x54000000-0x540fffff]
[ 1.405767] pci 0000:00:00.0: calling tango_pcie_bar_quirk+0x0/0x40
[ 1.412160] tango_pcie_bar_quirk: bus=0 devfn=0
[ 1.416843] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[ 1.423074] pcieport 0000:00:00.0: enabling bus mastering
[ 1.428652] altera_irq_domain_alloc: ENTER
[ 1.432876] FOO-msi 2e080.msi: msi#0 address_hi 0x0 address_lo 0x9002e07c
[ 1.440007] FOO-msi 2e080.msi: msi#0 address_hi 0x0 address_lo 0x9002e07c
[ 1.446972] aer 0000:00:00.0:pcie002: service driver aer loaded
[ 1.453157] pci 0000:01:00.0: calling quirk_usb_early_handoff+0x0/0x7e0
[ 1.459913] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 1.465709] quirk_usb_handoff_xhci: ioremap(0x54000000, 8192)
[ 1.471589] xhci_find_next_ext_cap: offset=0x500
[ 1.476325] val = 0x1000401
...
[ 1.624093] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.630675] ehci-pci: EHCI PCI platform driver
[ 1.635338] xhci_hcd 0000:01:00.0: enabling bus mastering
[ 1.640789] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.646071] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 1.659065] xhci_find_next_ext_cap: offset=0x500
[ 1.663714] val = 0x1000401
[ 1.666526] xhci_find_next_ext_cap: offset=0x510
[ 1.671171] val = 0x3000502
[ 1.673984] xhci_find_next_ext_cap: offset=0x510
[ 1.678632] val = 0x3000502
[ 1.681433] xhci_find_next_ext_cap: offset=0x524
[ 1.686079] val = 0x2000702
[ 1.688888] xhci_find_next_ext_cap: offset=0x524
[ 1.693533] val = 0x2000702
[ 1.696343] xhci_find_next_ext_cap: offset=0x540
[ 1.700987] val = 0x4c0
[ 1.703446] xhci_find_next_ext_cap: offset=0x550
[ 1.708091] val = 0xa
[ 1.710382] xhci_find_next_ext_cap: offset=0x510
[ 1.715028] val = 0x3000502
[ 1.717837] xhci_find_next_ext_cap: offset=0x524
[ 1.722482] val = 0x2000702
[ 1.725304] xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x00000010
[ 1.733801] xhci_hcd 0000:01:00.0: enabling Mem-Wr-Inval
[ 1.739222] altera_irq_domain_alloc: ENTER
[ 1.743393] altera_irq_domain_alloc: ENTER
[ 1.747543] altera_irq_domain_alloc: ENTER
[ 1.751674] FOO-msi 2e080.msi: msi#1 address_hi 0x0 address_lo 0x9002e07c
[ 1.758514] FOO-msi 2e080.msi: msi#2 address_hi 0x0 address_lo 0x9002e07c
[ 1.765347] FOO-msi 2e080.msi: msi#3 address_hi 0x0 address_lo 0x9002e07c
[ 1.772229] FOO-msi 2e080.msi: msi#1 address_hi 0x0 address_lo 0x9002e07c
[ 1.779098] FOO-msi 2e080.msi: msi#2 address_hi 0x0 address_lo 0x9002e07c
[ 1.785957] FOO-msi 2e080.msi: msi#3 address_hi 0x0 address_lo 0x9002e07c
[ 1.792979] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.799817] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.807085] usb usb1: Product: xHCI Host Controller
[ 1.811994] usb usb1: Manufacturer: Linux 4.9.7-1-rc2 xhci-hcd
[ 1.817863] usb usb1: SerialNumber: 0000:01:00.0
[ 1.823072] hub 1-0:1.0: USB hub found
[ 1.826890] hub 1-0:1.0: 4 ports detected
[ 1.831199] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 1.836473] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 1.843925] cmd=c8852020 status=c8852024
[ 1.847946] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.856168] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.863004] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.870275] usb usb2: Product: xHCI Host Controller
[ 1.875185] usb usb2: Manufacturer: Linux 4.9.7-1-rc2 xhci-hcd
[ 1.881055] usb usb2: SerialNumber: 0000:01:00.0
[ 1.886151] hub 2-0:1.0: USB hub found
[ 1.889964] hub 2-0:1.0: 4 ports detected
[ 1.894660] usbcore: registered new interface driver usb-storage
And when I insert/remove my Flash drive:
[ 216.216744] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 216.250189] usb 2-1: New USB device found, idVendor=0951, idProduct=1666
[ 216.256945] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 216.264130] usb 2-1: Product: DataTraveler 3.0
[ 216.268607] usb 2-1: Manufacturer: Kingston
[ 216.272821] usb 2-1: SerialNumber: 002618887865F0C0F8646BFA
[ 216.283005] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 216.289492] scsi host0: usb-storage 2-1:1.0
[ 217.299474] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 217.309981] sd 0:0:0:0: [sda] 15109516 512-byte logical blocks: (7.74 GB/7.20 GiB)
[ 217.320354] sd 0:0:0:0: [sda] Write Protect is off
[ 217.325722] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[ 217.331333] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 217.343691] sda: sda1
[ 217.347819] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 217.371940] random: fast init done
[ 217.547108] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 244.509391] pcieport 0000:00:00.0: AER: Uncorrected (Non-Fatal) error received: id=0000
[ 244.517478] pcieport 0000:00:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=0000(Requester ID)
[ 244.529525] pcieport 0000:00:00.0: device [1105:0024] error status/mask=00004000/00000000
[ 244.538033] pcieport 0000:00:00.0: [14] Completion Timeout (First)
[ 244.544940] pcieport 0000:00:00.0: broadcast error_detected message
[ 244.551301] pcieport 0000:00:00.0: AER: Device recovery failed
[ 244.828674] xhci_hcd 0000:01:00.0: Cannot set link state.
[ 244.834177] usb usb2-port1: cannot disable (err = -32)
[ 244.839359] usb 2-1: USB disconnect, device number 2
Hmmm, that sounds fishy.
# cat /proc/interrupts
CPU0 CPU1
19: 1958 2212 GIC-0 29 Edge twd
20: 107 0 irq0 1 Level serial
25: 1 0 PCIe MSI 0 Edge aerdrv
27: 471 0 PCIe MSI 524288 Edge xhci_hcd
28: 0 0 PCIe MSI 524289 Edge xhci_hcd
29: 0 0 PCIe MSI 524290 Edge xhci_hcd
IPI0: 0 0 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 1094 2376 Rescheduling interrupts
IPI3: 0 132 Function call interrupts
IPI4: 0 0 CPU stop interrupts
IPI5: 1 0 IRQ work interrupts
IPI6: 0 0 completion interrupts
Err: 0
The MSI indices look fishy.
524288 = 0x80000
Not sure where that come from.
# /usr/sbin/lspci -v
00:00.0 PCI bridge: Sigma Designs, Inc. Device 0024 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Memory at <ignored> (64-bit, non-prefetchable)
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 04000000-040fffff
Prefetchable memory behind bridge: 00000000-000fffff
Capabilities: [50] MSI: Enable+ Count=1/4 Maskable- 64bit+
Capabilities: [78] Power Management version 3
Capabilities: [80] Express Root Port (Slot-), MSI 03
Capabilities: [100] Virtual Channel
Capabilities: [800] Advanced Error Reporting
Kernel driver in use: pcieport
01:00.0 USB controller: Renesas Technology Corp. uPD720201 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI])
Flags: bus master, fast devsel, latency 0
Memory at 54000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Latency Tolerance Reporting
Kernel driver in use: xhci_hcd
Still some weirdness here.
I might be using too old a version: lspci version 3.2.1
And my current code, to work-around the silicon bugs:
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/of_pci.h>
#include <linux/of.h>
#include <linux/pci-ecam.h>
#include <linux/platform_device.h>
//#define DEBUG_CONFIG
static int tango_config_read(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 *val)
{
int ret;
void __iomem *pci_conf = (void *)0xf002e048;
#ifdef DEBUG_CONFIG
if (where == PCI_BASE_ADDRESS_0)
dump_stack();
#endif
writel(1, pci_conf);
if (devfn != 0) {
*val = ~0;
return PCIBIOS_DEVICE_NOT_FOUND;
}
ret = pci_generic_config_read(bus, devfn, where, size, val);
writel(0, pci_conf);
#ifdef DEBUG_CONFIG
printk("%s: bus=%d where=%d size=%d val=0x%x\n",
__func__, bus->number, where, size, *val);
#endif
return ret;
}
static int tango_config_write(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 val)
{
int ret;
void __iomem *pci_conf = (void *)0xf002e048;
#ifdef DEBUG_CONFIG
if (where == PCI_BASE_ADDRESS_0)
dump_stack();
#endif
#ifdef DEBUG_CONFIG
printk("%s: bus=%d where=%d size=%d val=0x%x\n",
__func__, bus->number, where, size, val);
#endif
writel(1, pci_conf);
ret = pci_generic_config_write(bus, devfn, where, size, val);
writel(0, pci_conf);
return ret;
}
static struct pci_ecam_ops tango_pci_ops = {
.bus_shift = 20,
.pci_ops = {
.map_bus = pci_ecam_map_bus,
.read = tango_config_read,
.write = tango_config_write,
}
};
static const struct of_device_id tango_pci_ids[] = {
{ .compatible = "sigma,smp8759-pcie" },
{ /* sentinel */ },
};
static int tango_pci_probe(struct platform_device *pdev)
{
return pci_host_common_probe(pdev, &tango_pci_ops);
}
static struct platform_driver tango_pci_driver = {
.probe = tango_pci_probe,
.driver = {
.name = KBUILD_MODNAME,
.of_match_table = tango_pci_ids,
},
};
builtin_platform_driver(tango_pci_driver);
#define RIESLING_B 0x24
/* Root complex reports incorrect device class */
static void tango_pcie_fixup_class(struct pci_dev *dev)
{
dev->class = PCI_CLASS_BRIDGE_PCI << 8;
}
DECLARE_PCI_FIXUP_EARLY(0x1105, RIESLING_B, tango_pcie_fixup_class);
static void tango_pcie_bar_quirk(struct pci_dev *dev)
{
struct pci_bus *bus = dev->bus;
printk("%s: bus=%d devfn=%d\n", __func__, bus->number, dev->devfn);
pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, 0x80000004);
}
DECLARE_PCI_FIXUP_FINAL(0x1105, PCI_ANY_ID, tango_pcie_bar_quirk);
Regards.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
