Felipe Balbi <felipe.balbi@xxxxxxxxxxxxxxx> writes:
> Hi Thinh,
>
> Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> writes:
>>> drivers/usb/dwc3/gadget.c | 5 +++++
>>> 1 file changed, 5 insertions(+)
>>>
>>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>>> index 6faf484e5dfc..0a664d8eba3f 100644
>>> --- a/drivers/usb/dwc3/gadget.c
>>> +++ b/drivers/usb/dwc3/gadget.c
>>> @@ -1379,6 +1379,9 @@ int __dwc3_gadget_ep_set_halt(struct dwc3_ep
>>> *dep, int value, int protocol)
>>> unsigned transfer_in_flight;
>>> unsigned started;
>>>
>>> + if (dep->flags & DWC3_EP_STALL)
>>> + return 0;
>>> +
>>> if (dep->number > 1)
>>> trb = dwc3_ep_prev_trb(dep, dep->trb_enqueue);
>>> else
>>> @@ -1400,6 +1403,8 @@ int __dwc3_gadget_ep_set_halt(struct dwc3_ep
>>> *dep, int value, int protocol)
>>> else
>>> dep->flags |= DWC3_EP_STALL;
>>> } else {
>>> + if (!(dep->flags & DWC3_EP_STALL))
>>> + return 0;
>>>
>>> ret = dwc3_send_clear_stall_ep_cmd(dep);
>>> if (ret)
>>> --
>>> 2.11.0.295.gd7dffce1ce
>>>
>>> --
>>
>> I encounter an issue when I test mainline with USB 3 CV MSC test and
>> bisected to this patch.
>>
>> Tester: USB 3 CV test (v2.1.3.0).
>> Function Driver: f_mass_storage
>> Reproducibility: always
>>
>> The failure occurs under MSC Error Recovery Test (TD 1.4).
>>
>> Failure from the test sequence as follow (MSC compliance test spec) :
>> 1. Place the device in the desired starting state.
>> 2. Issue a Case 9 CBW (see Table 2) but with invalid signature of 0xDEADBEEF.
>> 3. Issue several In requests to the Bulk-Only Data Interface Bulk In endpoint. Verify a
>> STALL handshake is returned. If STALL handshake is not returned, skip to step 11.
>> 4. Issue a Get_Status(endpoint) request targeting the Bulk-Only Data Interface bulk In
>> endpoint. Verify that it completes normally, reports endpoint halt status.
>>
>> ***After this point the device idles for 10 seconds and resets. ***
>>
>> Test fails.
>
> I've been looking at this and based on sniffer and dwc3 tracepoints, it
> seems like dwc3 is behaving properly. The real issue seems to be that
> g_mass_storage isn't queueing a new request to IN endpoint.
>
> I'll continue debugging this and try to find a solution that doesn't
> involve reverting $subject.
oh no, wait. ep2out misses XferInProgress:
file-storage-1592 [000] d..1 152.809922: dwc3_ep_queue: ep2out: req ffff88003cd6ee40 length 0/512 zsI ==> -115
file-storage-1592 [000] d..1 152.809931: dwc3_prepare_trb: ep2out: 3/8 trb ffff88003a196050 buf 000000002d5e4000 size 512 ctrl 00000819 (HlcS:sC:normal)
file-storage-1592 [000] d..1 152.809942: dwc3_gadget_ep_cmd: ep2out: cmd 'Update Transfer' [262151] params 00000000 00000000 00000000 --> status: Successful
file-storage-1592 [000] .... 152.809951: usb_ep_queue: ep2out: length 0/512 sgs 0/0 stream 0 zsI status -115 --> 0
irq/34-dwc3-1593 [001] d..1 152.810212: dwc3_event: event (0000c040): ep0out: Transfer Complete [Setup Phase]
irq/34-dwc3-1593 [001] d..1 152.810218: dwc3_ctrl_req: bRequestType 02 bRequest 01 wValue 0000 wIndex 0002 wLength 0
irq/34-dwc3-1593 [001] d..1 152.810228: __dwc3_gadget_ep_set_halt: ep2out: NOT stalled
Sniffer shows me this completing, but I don't see IRQ for this.
--
balbi
Attachment:
signature.asc
Description: PGP signature
