add a new compatible string for "mt2712", and move reference clock
into each port node;
Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
.../devicetree/bindings/phy/phy-mt65xx-usb.txt | 93 +++++++++++++++++---
1 file changed, 80 insertions(+), 13 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
index 33a2b1e..0acc5a9 100644
--- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
+++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
@@ -6,12 +6,11 @@ This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
Required properties (controller (parent) node):
- compatible : should be one of
"mediatek,mt2701-u3phy"
+ "mediatek,mt2712-u3phy"
"mediatek,mt8173-u3phy"
- - reg : offset and length of register for phy, exclude port's
- register.
- - clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
- - clock-names : must contain
+ - clocks : (deprecated, use port's clocks instead) a list of phandle +
+ clock-specifier pairs, one for each entry in clock-names
+ - clock-names : (deprecated, use port's one instead) must contain
"u3phya_ref": for reference clock of usb3.0 analog phy.
Required nodes : a sub-node is required for each port the controller
@@ -19,8 +18,19 @@ Required nodes : a sub-node is required for each port the controller
'reg' property is used inside these nodes to describe
the controller's topology.
+Optional properties (controller (parent) node):
+ - reg : offset and length of register shared by multiple ports,
+ exclude port's private register. It is needed on mt2701
+ and mt8173, but not on mt2712.
+
Required properties (port (child) node):
- reg : address and length of the register set for the port.
+- clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+- clock-names : must contain
+ "ref": 48M reference clock for HighSpeed analog phy; and 26M
+ reference clock for SuperSpeed analog phy, sometimes is
+ 24M, 25M or 27M, depended on platform.
- #phy-cells : should be 1 (See second example)
cell after port phandle is phy type from:
- PHY_TYPE_USB2
@@ -31,21 +41,31 @@ Example:
u3phy: usb-phy@11290000 {
compatible = "mediatek,mt8173-u3phy";
reg = <0 0x11290000 0 0x800>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "u3phya_ref";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "okay";
- phy_port0: port@11290800 {
- reg = <0 0x11290800 0 0x800>;
+ u2port0: usb-phy@11290800 {
+ reg = <0 0x11290800 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
- phy_port1: port@11291000 {
- reg = <0 0x11291000 0 0x800>;
+ u3port0: usb-phy@11290900 {
+ reg = <0 0x11290800 0 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u2port1: usb-phy@11291000 {
+ reg = <0 0x11291000 0 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
+ clock-names = "ref";
#phy-cells = <1>;
status = "okay";
};
@@ -64,7 +84,54 @@ Example:
usb30: usb@11270000 {
...
- phys = <&phy_port0 PHY_TYPE_USB3>;
- phy-names = "usb3-0";
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+ phy-names = "usb2-0", "usb3-0";
...
};
+
+
+Layout differences of banks between mt8173/mt2701 and mt2712
+-------------------------------------------------------------
+mt8173 and mt2701:
+port offset bank
+shared 0x0000 SPLLC
+ 0x0100 FMREG
+u2 port0 0x0800 U2PHY_COM
+u3 port0 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 U2PHY_COM
+u3 port1 0x1100 U3PHYD
+ 0x1200 U3PHYD_BANK2
+ 0x1300 U3PHYA
+ 0x1400 U3PHYA_DA
+u2 port2 0x1800 U2PHY_COM
+ ...
+
+mt2712:
+port offset bank
+u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+u3 port0 0x0700 SPLLC
+ 0x0800 CHIP
+ 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+u3 port1 0x1700 SPLLC
+ 0x1800 CHIP
+ 0x1900 U3PHYD
+ 0x1a00 U3PHYD_BANK2
+ 0x1b00 U3PHYA
+ 0x1c00 U3PHYA_DA
+u2 port2 0x2000 MISC
+ ...
+
+ SPLLC shared by u3 ports and FMREG shared by u2 ports on
+mt8173/mt2701 are put back into each port; a new bank MISC for
+u2 ports and CHIP for u3 ports are added on mt2712.
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
