On Tue, Nov 22, 2016 at 2:51 PM, Christian Lamparter
<chunkeey@xxxxxxxxxxxxxx> wrote:
> On Monday, November 21, 2016 7:32:30 PM CET John Youn wrote:
>> On 11/21/2016 1:10 PM, Christian Lamparter wrote:
>> > On Monday, November 21, 2016 12:16:31 PM CET John Youn wrote:
>> >> On 11/18/2016 12:18 PM, Christian Lamparter wrote:
>> >>> On Friday, November 18, 2016 8:16:08 AM CET Rob Herring wrote:
>> >>>> Also, perhaps you should allow that the compatible string can define the
>> >>>> default.
>> >>>>
>> >>> I hoped you would say that :).
>> >>>
>> >>> I've attached a patch (on top of John Youn changes) [...]
>> >>> ---
>> >>> Subject: [PATCH] usb: dwc2: add a default ahb-burst setting for amcc,dwc-otg
>> >>> [...]
>> >>> @@ -1097,6 +1097,22 @@ static const char *const ahb_bursts[] = {
>> >>> +/* [...] */
>> >>> +static const struct of_device_id dwc2_compat_ahb_bursts[] = {
>> >>> + {
>> >>> + .compatible = "amcc,dwc-otg",
>> >>> + .data = (void *) GAHBCFG_HBSTLEN_INCR16,
>> >>> + },
>> >>> +};
>> [...]
>> > >>> @@ -1107,6 +1123,12 @@ static int dwc2_get_property_ahb_burst(struct dwc2_hsotg *hsotg)
>> >>> ret = device_property_read_string(hsotg->dev, "snps,ahb-burst", &str);
>> >>> if (ret < 0) {
>> >>> + const struct of_device_id *match;
>> >>> +
>> >>> + match = of_match_node(dwc2_compat_ahb_bursts, node);
>> >>> + if (match)
>> >>> + ret = (int)match->data;
>> >>> +
>> [...]
>> >> I'd prefer if you use the binding which requires no extra code in
>> >> dwc2.
>> > I'm fine with either option. However it think that this would require
>> > that either Mark or Rob would allow an exception to the "keep existing
>> > dts the way they are) and ack the following change to the canyonlands.dts.
>>
>> I don't know about that. Under what circumstance can the dts change?
> As far as I know, the justification for not changing the DTS is that a
> compiled DTB might be stored in an read-only ROM on a board. So it would
> be impossible to update it. Hence, the driver have work with the existing
> (and sometimes buggy or incomplete) information to stay compatible.
>
> (Note: Thankfully, the canyonlands dtb is stored in flash, it's possible
> to update it. But it is an extra step that's not done automatically
> with make install).
>
>> The canyonlands dts was binding to an external vendor driver. So it
>> wasn't documented nor expected to work with dwc2 until your recent
>> patch adding the compatible string.
>
> Oh, no that's not what happend. Let me explain why there was no "external
> vendor driver": AMCC/APM were planing to upstream their hole platform. And
> in fact, the devs tried very hard to include their driver back in 2011 [0].
> But this driver was denied inclusion back then due to:
>
> "[...]
> I would also like to point out that the same Synopsys USB controller
> is used in a number of other SoCs (especially ARM chips), and
> supported by other drivers, some of these even in mainline.
>
> See http://thread.gmane.org/gmane.linux.usb.general/61714/focus=62139
> for a related thread.
>
> Instead of trying to add a completely new driver to mainline (and one
> which has been repeatedly been rejected), I vote for focusing on the
> existing driver code that is already in mainline, and testing and
> improving this so we can use a single implementation of this driver
> code for all SoCs that use the same IP block." [1]
>
> Of course: The listed link goes the "USB Host driver for i.MX28" driver.
> And this is an ehci-hcd like driver... Which is as you are well aware not
> that similar to the dwc2 OTG. And as far as I can tell: AMCC abandoned
> the patch series right there.
>
> Note: AMCC did however succeed in pushing your employer's Synopsys
> DesignWare SATA and DMA drivers to the kernel back then. And I'm happy
> to report that both drivers are still around and working fine for the 460EX
> (sata_dwc_460ex.c[2] and the DW AHB DMA [3]). (The drivers also work for
> different platforms than the original PPC. I know that because I helped
> Andy Shevchenko with testing and pushing some fixes to it when he was
> adding support for the Intel Quark SoC, which uses the DWC SATA and DMA).
>
> So Please?
>> Systems that use the vendor driver will still work with the dts. If
>> you remove the vendor driver and configure it to use dwc2, it won't
>> work due to a quirk of the canyonlands hardware, for which you need to
>> add a dts property.
> Sadly, there is no up to date vendor driver. The canyonlands.dts binding
> is still in place and the hardware works fine. I'm interested in this
> platform since it is a cheap BigEndian system which is useful for usb
> driver development (carl9170 and rtl8192su)... and I would like to
> have out-of-the-box support.
>
>> I think this is reasonable. Rob or Mark, any feedback?
> I recall that Rob has already voiced his opinion about the ahb-burst setting:
> "Also, perhaps you should allow that the compatible string can define the default."
>
> And based on that, I made the "add a default ahb-burst setting for amcc,dwc-otg"
> patch above. Of course, it would be nice to have any feedback too. But unless I
> hear otherwise, I'll continue with posting patches to the dwc2 driver :).
And this is the correct thing to do. Requiring a dtb update is not.
Rob
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
