On Sat, Nov 12, 2016 at 12:11:04AM +0200, Laurent Pinchart wrote:
> Hello,
>
> On Friday 11 Nov 2016 08:53:22 Tony Lindgren wrote:
> > * Bin Liu <b-liu@xxxxxx> [161111 08:25]:
> > > On Fri, Nov 11, 2016 at 01:39:28AM +0200, Laurent Pinchart wrote:
> > >> Hello,
> > >>
> > >> On Friday 11 Nov 2016 00:27:52 Laurent Pinchart wrote:
> > >>> On Thursday 10 Nov 2016 13:42:34 Tony Lindgren wrote:
> > >>>> * Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> [161110 13:29]:
> > >>>>> I had to disable CONFIG_USB_GADGET is compiling it as a module
> > >>>>> prevents selecting CONFIG_NOP_USB_XCEIV=y, which is a dependency for
> > >>>>> CONFIG_USB_EHCI_HCD_OMAP=m.
> > >>>>>
> > >>>>> The new configuration resulted in a few changes, among which the
> > >>>>> most notable is
> > >>>>>
> > >>>>> -# CONFIG_USB_MUSB_HOST is not set
> > >>>>> -# CONFIG_USB_MUSB_GADGET is not set
> > >>>>> -CONFIG_USB_MUSB_DUAL_ROLE=y
> > >>>>> +CONFIG_USB_MUSB_HOST=y
> > >>>>>
> > >>>>> I then get the same error as originally reported.
> > >>>>
> > >>>> Yeah OK, that's the problem.. We still have musb hardware
> > >>>> trying to do things on it's own and phy trying to detect
> > >>>> the state.
> > >>>>
> > >>>> Any ideas why we have a dependency like that in Kconfig?
> > >>>
> > >>> Well, with CONFIG_USB_GADGET disabled, I don't expect
> > >>> CONFIG_USB_MUSB_GADGET to be enabled. MUSB can only operate in host
> > >>> mode in that case, so musb-> xceiv->otg->state = OTG_STATE_A_IDLE
> > >>> makes sense.
> > >>
> > >> I've tried to investigate this but I'm not familiar enough with the MUSB
> > >> driver to reach any conclusion. Felipe, if you have time could you give
> > >> me a hand ?
> > >>
> > >> To summarize the issue, on a pandaboard-es where the MUSB is wired to an
> > >> OTG connector with mode rightfully set to MUSB_PORT_MODE_DUAL_ROLE in
> > >> DT, a kernel configured with CONFIG_USB_MUSB_HOST=y (for instance
> > >> because CONFIG_USB_GADGET is disabled) will print an endless stream of
> > >> the following meessage.
> > >>
> > >> [ 2.766174] musb_bus_suspend 2586: trying to suspend as a_idle while
> > >> active
> > >
> > > I don't have a omap3/4 platform to test on this, but I don't see this
> > > problem on am335x board.
>
> Which board is that ? For the problem to occur the board has to have an OTG
> connector.
It is the TI am335x GP EVM, which usb0 port has an otg receptacle, and a
power switch controlled by usb0 drvvbus pin.
>
> > >> musb_init_controller() performs the following actions
> > >>
> > >> case MUSB_PORT_MODE_DUAL_ROLE:
> > >> status = musb_host_setup(musb, plat->power);
> > >> if (status < 0)
> > >> goto fail3;
> > >> status = musb_gadget_setup(musb);
> > >> if (status) {
> > >> musb_host_cleanup(musb);
> > >> goto fail3;
> > >> }
> > >> status = musb_platform_set_mode(musb, MUSB_OTG);
> > >> break;
> > >>
> > >> and as gadget support is disabled musb_gadget_setup() compiles to a
> > >> no-op inline function. The system is thus configured in host mode by
> > >> musb_host_setup() with musb->xceiv->otg->state = OTG_STATE_A_IDLE. A
> > >> later call to musb_start() verifies the condition
> > >>
> > >> if (musb->port_mode != MUSB_PORT_MODE_HOST &&
> > >> musb->xceiv->otg->state != OTG_STATE_A_WAIT_BCON &&
> > >> (devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) {
> > >
> > > To get there, devctl[MUSB_DEVCTL_VBUS] bits have to be set, where does the
> > > vbus voltage come from? Session is not on yet.
>
> MUSB_DEVCTL is first set to 0 by musb_generic_disable() called from
> musb_init_controller(). The register is then left untouched (as far as I can
> tell, I've intercepted all musb_writeb() and musb_readb() calls) until
> musb_start() to reads the register. The read value has BDEVICE and VBUS=3 set.
The DEVCTL_VBUS bits are set by the controller, when it sense VBUS
voltage > VBUS_VALID.
>
> > >> and sets musb->is_active to 1. Later, musb_bus_suspend() complains
> > >> because is_active is not 0.
> > >>
> > >> What is wrong in that sequence ?
> >
> > I think the issue is pandaboard connected to a PC with mini-B
> > cable while musb is being forced to host mode?
>
> The issue also occurs when the cable isn't connected.
If the otg port is not connected to a host but you still get VBUS=3, the
vbus voltage must be provided from the board itself. We have to check
the schematics to see how it is possible. This is pandaboard es, right?
Assume I will be able to find its schematics on internet...
>
> --
> Regards,
>
> Laurent Pinchart
>
Regards,
-Bin.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
