Hi Vivek, On Di, 2016-10-04 at 17:32 +0530, Vivek Gautam wrote: > Hi Michael, > > > On Tue, Oct 4, 2016 at 4:28 PM, Michael Niewöhner <linux@xxxxxxxxxxxxxx> wrote: > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > [1.] One line summary of the problem: > > > > > > > DWC3 USB 3.0 not working on Odroid-XU4 with Exynos 5422 > > > > > > > > > > > > > > [2.] Full description of the problem/report: > > > > > > > No usb 3.0 devices are being detected when attached while USB 2.0 > > > > > > > devices work on the same port. > > > > > > > USB 3.0 works after applying patches [9.1] and [9.2], but seems > > > > > > > to be > > > > > > > buggy. The usb hub is redetected every time an usb device is > > > > > > > attached. > > [snip] > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > [9.] Other notes, patches, fixes, workarounds: > > > > > > > > [9.1] https://lkml.org/lkml/2014/4/28/234 > > > > > > > > [9.2] https://lkml.org/lkml/2015/2/2/259 > > > > > > These patches are required to get USB super-speed working on Exynos5420/5800. > > > But they did not make to upstream. There was resistance on adding new > > > phy_calibrate() > > > callback. > > > > > > Without these patches the Exynos5420/5800 will enumerate all > > > super-speed capable devices > > > as high-speed devices. > > > Last time we checked with exynos542x smdk boards and peach-* boards, > > > we could get the > > > Super - speed devices working. I have not tested odroid anytime so > > > don't have much idea about the > > > its intricacies. > > > I guess Anand was able to use these patches to get his kernel working in past. > > > > > > The patches don't work anymore with 4.8-rc* / 4.8. They worked - but very > > unstable - with 4.7. > > > > One more problem appeared since one of the 4.8-RCs: reboot hangs when the dwc3 > > module is loaded. If I unload it before reboot / shutdown everything is fine. > > > > > > > > > > > > > When you have a downstream on-board usb hub, ideally it should be able > > > to detect the devices > > > and not reset everytime you connect a new device (like you mentioned earlier). > > > There can be two possible reasons why the hub keeps getting reset ever > > > after applying the above > > > mentioned patches: > > > 1) the clock rates are not proper. > > > 2) the regulator load setting is not enough to drive the hub. > > > > > > Anand, can you please point Michael to an older kernel with which you > > > could test usb on odroid successfully ? > > > You can compare the clocks with an older version and see if there'a > > > any difference. > > > > > > Any possibility of any other framework (such as, bus-freq) trimming > > > down the clock - rates ? > > > > > > ################################ > > # v4.7.5 > > ################################ > > > > $ cat /sys/kernel/debug/clk/clk_summary | grep usb > > sclk_usbh20_scan_clk 0 0 480000000 0 > > sclk_usbh20 0 0 48000 > > 000 0 > > mout_usbd300 1 1 24000000 0 > > dout_usbd300 0 0 24000000 0 > > sclk_usbd300 > > 0 0 24000000 0 > > dout_usbphy300 1 1 24000000 0 > > sclk_usbphy300 4 4 24000 > > 000 0 > > mout_usbd301 1 1 24000000 0 > > dout_usbd301 0 0 24000000 0 > > sclk_usbd301 > > 0 0 24000000 0 > > dout_usbphy301 1 1 24000000 0 > > sclk_usbphy301 3 3 24000 > > 000 0 > > usbd301 1 1 100000000 > > usbd300 1 1 100000000 > > > > usbh20 3 3 100000000 0 > > > > > > > ################################ > > # v4.8.0 > > ################################ > > > > $ cat /sys/kernel/debug/clk/clk_summary | grep usb > > sclk_usbh20_scan_clk 0 0 480000000 0 > > sclk_usbh20 0 0 48000000 > > 0 > > mout_usbd300 1 1 24000000 0 > > dout_usbd300 0 0 24000000 0 > > sclk_usbd300 > > 0 0 24000000 0 > > dout_usbphy300 1 1 24000000 0 > > sclk_usbphy300 4 4 24000000 > > 0 > > mout_usbd301 1 1 24000000 0 > > dout_usbd301 0 0 24000000 0 > > sclk_usbd301 > > 0 0 24000000 0 > > dout_usbphy301 1 1 24000000 0 > > sclk_usbphy301 3 3 24000000 > > 0 > > usbd301 1 1 100000000 > > This clock should have been 200MHz. > > > > > usbd300 1 1 100000000 > > usbh2 > > 0 3 3 100000000 0 > > > > $ cat /sys/kernel/debug/usb/devices > > <<system hangs>> > > > > The clocks are same across working/non-working. > Is it possible to bisect the commit that's causing hang for 4.8x ? [c499ff71ff2a281366c6ec7a904c547d806cbcd1] usb: dwc3: core: re-factor init and exit paths This patch causes both the hang on reboot and the lsusb hang. > > Adding few of the folks from Samsung who can test dwc3 usb on smdk/peach boards. > +Alim, Pankaj > > Hi Alim, Pankaj, > can you please give a try with 4.8 kernel on peach/smdk542x board and > see if dwc3 usb works or not. > You may need to the patches mentioned in [9.1] and [9.2] mentioned above. > > > [snip] > > > Thanks > Vivek > Best regards Michael��.n��������+%������w��{.n�����{���)�� jg��� �����ݢj����G���� ���j:+v���w�m������w�������h�����٥
